Search Documents

Note: This is a progress report and therefore not necessarily conclusive. Further data may result in conclusions somewhat different from those reported here. Crop Growing Season The monthly average temperatures, total precipitation, and evaporation for the demonstration mine are shown in Table 1. [ ]

Jan 1, 1980

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By William F. Hahn

This project focused effort on three separate areas: demonstration of a low seam longwall illumination system, design of illumination systems for low coal auger miners, and an assessment of machine lighting systems for machinery used to mine low seam coal. Results indicated illumination systems can be purchased by the mine operators of low coal seams. These systems can be supplied with the equipment as a factory integrated system or can be retrofitted to the machine or longwall equipment.

Jan 1, 1982

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

By D. W. Dareing

Multiple branch wellbores and horizontal holes, when applied to deep lying ore bodies, have the potential of significantly reducing well costs by reducing total footage drilled per acre of well pattern. In addition, horizontal holes may increase sweep efficiency. Well completion is a major problem. They must be cased to contain leaching solutions within the underground portion of the production loop. Several drilling and completion concepts are given and evaluated in the report. Our evaluation shows that there is economic incentive to further develop these concepts for field application to ore bodies 1,500 feet. Multiple branch concepts are the most attractive. They can reduce well costs by as much as 30° when applied to 2,000 feet ore body depths (44%, at 5,000 feet) and can accommodate a lamer pump than conventional vertical wells. We recommend this concept be developed further to accommodate either dual or triple branches.

Jan 1, 1980

By Louis C. Brichta

"The O'Jack Mining Co.'s zinc and lead deposits in Jasper County, Missouri, have been worked intermittently since the early nineties; production from these deposits was greatest during World War I and II - 4,668 tons of zinc and lead concentrates. The deposits are in a sink-hole structure in which intense deformation has taken place and in areas of disturbance in the sheet-ground horizon.While high-grade ore was being mined, the operators sank seven churn-drill holes for the purpose of extending reserves. They then asked the Bureau of Mines to explore the deposit with the object of developing a reserve of lower-grade ore that could be mined by open-pit methods. Twenty-two holes were sunk. The methods of drilling and sampling and the logs of the holes, as of those drilled by the operators, are given later in this report.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mined has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts development by each exploratory project as soon as practicable after its conclusion. Preliminary examination, conduct of exploratory work, and preparation of final reports are functions of the Mining Branch, Lowell B. Moon, chief, under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By C. P. Mishra

The Bureau of Mines performed a study of the availability of cobalt from market economy countries. The study entailed the detailed analysis of 97 deposits which contain 3.9 billion lb of cobalt at the demonstrated level; in 94 of the deposits cobalt is recovered as a byproduct, and in 3 it is considered the primary product. Since 97 pet of all recoverable cobalt is derived as a byproduct from copper and nickel deposits, the report focused on these two sources. At an assumed market price of $0.89flb for copper, $3.45/lb for nickel, $475/tr 021 for platinum, and $7/lb for cobalt, 1,330 million lb of cobalt at the demonstrated level are potentially available. This total includes 1,105 million lb of cobalt from copper properties, 190 million lb from nickel, 29 million lb from platinum, and 6 million lb from primary cobalt. This analysis indicates that the production cost for 589 million lb of cobalt can be totally covered by the revenues obtained from the other metals produced. The impacts of increases in capital investment and energy costs are also discussed.

Jan 1, 1985

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By H. E. Harris

It has long been recognized that one of the principal ways of combating dust in coal mines is by means of water sprays. However, spray systems, currently in use, clog or plug frequently, thereby reducing the effectiveness of dust control aid, in turn, possibly increasing the health hazard to mining personnel. Moreover, the maintenance and replacement of spray system components, e.g., nozzles and filters, can be expensive in terms of direct costs of labor and material, and the consequent loss of production. Recognizing these problems, the Bureau of Mines sponsored a research project on the "Development of a Non-Clogging Water Spray System"; this project was carried out by Eastern Associated Coal Corp. The overall objective of this project was to develop a non-clogging water spray system suitable for use in underground coal mines. Since most of the dust formed is at or near the working coal face, emphasis was placed on face equipment such as a continuous mining machine. To accomplish this objective, a two-phase project was carried out. The first phase involved determining the causes of spray nozzle and spray system clogging, determining the availability of spray nozzles or systems that could be modified to be non-clogging, and developing a non-clogging water spray system. Phase two was concerned with the fabrication and the laboratory and field testing of a non-clogging system. In each phase, there were both laboratory and field investigations, and the results of these investigations are presented in this report.

Jan 1, 1975

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much infor- mation was collected on the salt resources and industry of the United States. The more important features of the information thus gath- ered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geologi- cal Survey, which will supplement this report, relating to salt- making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Wash- ington, D. C. In addition to the discussion of processes, this report gives a brief description of the more important sources of salt in the United States. This description has been abstracted from the much length- ier description contained in the report to be published by the Geo- logical Survey.

Jan 1, 1917