Search Documents

By Robert L. Lagace

The objective of this task was to perform theoretical analyses related to identifying and increasing the understanding of wireless propagation mechanisms in mines, and for predicting the performance ranges and limitations of proposed systems. This was to be achieved by building on and extending previous ADL work* and utilizing experimental data as they became available in the radio frequency bands of interest. B. TASKS Theoretical radio wave propagation investigations undertaken on this task centered on three areas. The first area dealt with extending previous UHF wireless propagation results*: to estimate the losses caused by the presence of haulage vehicles such as trains in coal mine tunnels; to estimate the propagation losses and wireless communication ranges expected along a longwall coal face tunnel; and to assess the applicability of previous analytical approximations to tunnels having reduced crossectional dimensions, such as those found in low coal and in the presence of haulage vehicles. The second area dealt with the development of a suitable propagation model to adequately explain the unexpected, highly favorable LF to MF band wireless radio wave propagation behavior experimentally observed in Consolidation Coal Co.'s Ireland mine. The third area dealt with the formulation of a model for evaluating the overall system transfer function and transmitter requirements for a hoist shaft LF communications system, taking into account the hoist rope/shaft transmission line characteristics, the cage and sheave wheel line terminations, the signal inductive couplers, and hoist shaft signal and noise data.

Jan 1, 1975

To provide an engineering solution to wood crib design and deployment strategies that will ensure safety for underground coal mine workers. This is accomplished by preserving necessary ground control requirements while minimizing support costs or by developing new support strategies to enhance ground support in difficult conditions. A secondary objective is to be able to quantify wood crib support performance to define support requirements for alternative support systems. These objectives have been achieved through a simple-to-use computer program called the wood crib performance model (wcpm).

Jan 1, 1997

An active list of permissible explosives was published in December 1936 as part of Bureau of Mines Report of Investigations 3324, under the title "Active List of Permissible Explosives and Blasting Devices Approved Prior to July 31, 1936." This list included 170 brand names. Changes in the list that have been authorized to June 30, 1937 placed 35 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Ten permissible explosives were transferred from the active to the inactive list. The present list contains 196 brand names, one explosive having been placed on the list subsequent to June 30, 1937. The brand names of the permissible explosives placed on the active list are as follows:

Jan 1, 1937

By Gordon E. Green

This report addresses remote monitoring of coal waste impoundments for stability. Existing automated geotechnical monitoring systems are described and reviewed along with details of instruments suitable for such systems. An impoundment in West Virginia which was in the construction stage was instrumented and monitored between July 1979 and may 1981. Sensors which measure surface and subsurface parameters including settlement, horizontal deflection, surface tilt, pore water pressure, seepage, pond level, and meteorological parameters were installed. Data from the 37 sensors were collected by on-site logger and transmitted by telephone to a central processing station in Seattle for recording and interpretation. Difficulties were encountered with telephone and powerline outages and malfunction of electronic units. Detailed descriptions of the design and performance of the system are provided along with evaluation and comparison with other systems. Recommendations for improving and expanding the capabilities of the monitoring system are given.

Jan 1, 1982

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of lead and zinc from 104 domestic mines and deposits. Fourteen primary lead and fifty-three primary zinc operations with in situ demonstrated resources containing 27.3 million metric tons (t) of lead and 53 million t of zinc were subsequently evaluated. Potentially 17.5 million t of lead and 2.4 million t of byproduct zinc could be recovered from 14 primary lead operations. Economic evaluations performed in constant January 1982 dollars determined a long-run total cost per pound of recoverable commodity. Including a 15-pct discounted-cash-flow rate of return (DCFROR), 59 pct of primary lead was potentially available at or below $0.32 per pound of lead. Potentially 40 million t of zinc and 5.6 million t of byproduct lead could be recovered from 53 primary zinc operations. Ninety percent of the recoverable zinc is potentially available from currently nonproducing mines and deposits, and a weighted average of their long-run total costs was determined at $0.98 per pound of zinc. At a breakeven (0-pct) DCFROR, these non producing operations had a weighted average long-run total cost of $0.58 per pound of zinc. Sensitivity analyses illustrated that operations that recover byproducts were most sensitive to fluctuating metal prices, producing operations were more sensitive to increased smelter treatment charges, and nonproducing operations were impacted most by the DCFROR.

Jan 1, 1983

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is in-tended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By G. L. Oldright

As a rule, the usual zinc retort smelter fired with natural gas made its own burners, of which there might be 300 per block, out of standard pipe fit-tings. The gas was discharged through a feeder pipe at various distances into a cylindrical horizontal "blow hole" through a pillar block and thence into the furnace; the best location of this gas-feeder pipe was at the horizontal central axis of the blow hole; the side entry into the blow hole usually was used. The air entered the same blow hole behind the gas, through a short nipple, in the inner end of which was a constructing orifice in a clay plug; in this ,work cone-shaped funnels of various lengths also were used. Even with the air and gas correctly proportioned to each burner, small differences in their dimensions were found to influence greatly the temperatures reached, their uniformity, and consequently the percentage of zinc extracted. This fourth paper of a series on cooperative work in the zinc retort plants of the Eagle-Picher Mining & Smelting Company discloses the methods and principles followed in approximating closely the optimum dimensions for various burners, with examples from experimental and commercial furnaces showing the interrelation of such dimensions with combustion and temperatures in the furnace.

Jan 1, 1948

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Launa Mallett, Charles Vaught, Michael J. Brnich

Purpose: This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings. Intended Use: This material has been developed for use in short safety-training sessions such as start-of-shift safety or Atoolbox@ talks. The information can be presented in approximately fifteen minutes and is appropriate for workers at all experience levels. While the examples and illustrations are taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. Materials Needed: The instructor will need to prepare the figures provided in a form that can be seen by the entire class. Suggested methods include the use of: (1) overhead transparencies, (2) laminated pages that can be held up for small groups, and/or (3) handouts with copies of the figures for each trainee. As a supplement, stickers featuring the communication triangle can be placed on hard hats, telephones or other communication devices to remind workers about the key to effective emergency communication. The Talk: The accompanying script is a guide for presenting this safety talk. Training is enhanced if these materials are covered but not simply read by the trainer. Examples given in this guide are from real experiences. To make training more interesting and effective, the instructor can substitute examples from his/her workplace. Additional Resources: The following references will provide further information about communications during emergencies. Auf Der Heide, E. (1989). Disaster Response: Principles of Preparation and Coordination. The C.V. Mosby Company, St. Louis. Mallett, Launa, Charles Vaught, and Michael J. Brnich Jr. (1993). A Sociotechnical Communication in an Underground Mine Fire: A Study of Warning Messages During an Emergency Evacuation@, Safety Science, 16, pp. 709-728. Nigg, J.M. (1987). A Communication and Behavior: Organizational and Individual Response to Warnings@ in Sociology of Disasters: Contributions of Sociology to Disaster Research, R.R. Dynes, B. De Marchi, and C. Pelanda (eds.), Franco Angeli, Milan, Italy, pp. 103-116.

Jan 10, 1999

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977