Search Documents

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By E. P. Youngman

The mining law of British North Borneo is entitled " The Mining Ordinance , 1927. 113 The only mining regulation or rule available is " Rules 313 , 114 passed in accordance with article 26 of the ordinance of 1927. Before the passage of this legislation , the country had no specific law governing the granting of mineral rights , although the land law contained provisions relating to mining lands . The land ordinance of 19135 still controls in a few details . All references in this paper , unless otherwise specifically designated , are to the mining ordinance .

Mar 1, 1933

By Paul M. Ambrose

THE ABRASIVES INDUSTRY throughout the world enjoyed a profitable year. With the exception of tripoli, the quantity of each kind of abrasive produced in the United States was greater than for any of the past 5 years and value of each was greater than for many years. Production of silicon carbide both in the United States and in Canada was the largest since 1960. Abrasive machining, which offers great potential for the increased Use of aluminum oxide, contributed to increased industrial productivity. Diamonds from the sea off the coast of South-West Africa attracted wide interest. Much of the production from this source has been gem diamond, and there is little likelihood of significant quantities of industrial diamond from that source. Manufactured diamond from all free-world sources was sold in the United States in 1964.

Jan 1, 1965

By E. G. Meiter, S. H. Katz

"Railroad locomotives produce heat, gas, and smoke, which cause considerable discomfort to engine men and firemen while passing through tunnels. In order to try and improve these conditions, the Bureau of Mines has investigated the composition of atmospheres in cabs of freight locomotives while in tunnels; and some of the higher temperatures in the cabs were noted; physiological effects upon men were determined and gas masks and respirators were devised to eliminate the effects of irritating and poisonous gases and smoke. Those investigations were conducted in tunnels of the Baltimore & Ohio, Pennsylvania, and Union Pacific railroads; while that described in this paper was carried out in tunnels of the Chesapeake & Ohio, Railroad, situated in the Blue Ridge and Allegheny Mountains in Virginia and West Virginia, Freight locomotives used by this railroad are of the Mallet type, which have two separate cylinders: and two separate sets of driving wheels on each side. In locomotive language they are of the 2-6-6-2 type. All of the cylinders act as simple engines when starting or in slow, heavy hauling; but at faster speeds the pair of cylinders on each side operate compound, Mallet locomotives are the largest and most powerful now operated.The tendency in train operation has always been to increase the burden upon locomotives, Present traffic needs frequently load even the Mallet engine to capacity, and yet the weight of trains tends to increase. It has been suggested as a means of securing greater power units that Mallets be constructed to operate only as simple engines. This would increase the amount of steam given off as the amount of coal burned and the resulting volume of flue gas emitted."

Jul 1, 1924

By Alton B. Cook, G. B. Shea

"INTRODUCTION In February 1945, Captain (now Commodore) W. G. Greeman, U. S. N., Director, Naval Petroleum and Oil 3hale Reserves, requested the Bureau of Mines to assist the Navy in its wartime development of Naval Petroleum Reserve No. 1, Elk Hills field, Calif., to assure adequate supplies of petroleum products in the Pacific theatre. Unit Operation 4/,engineers desired pressure volume-temperature and viscosity data on the reservoir oil in the shallow oil zone to augment data previously obtained for the purpose of calculating reservoir performance and oil reserves. Accordingly, arrangements were approved by the Operating Committee far, the Bureau of Mines to proceed with a program of field sampling and laboratory determinations designed to obtain the desired information.To carry out the assignment, the Bureau transferred the necessary person¬nel, subsurface pressure, temperature, and sampling instruments, and laboratory equipment for analyzing subsurface oil samples from the Petroleum Experiment Station, Bartlesville, Okla., and the San Francisco, Calif., office and set up a temporary field headquarters in the Elk Hills. The program of work as out-lined by Unit Operation required the 6 months period March-August 1945 to complete during which time individual reports comprising data on pressure-volume-temperature relationships and reservoir oil viscosities as determined on subsurface oil samples and recombined oil and gas samples for 5 selected wells were submitted to Unit Operation.This report is a summary compilation of the data contained in the original reports supplemented by correlations of some of the physical properties of the reservoir oil with the A.P.I. gravities of the produced oil. The report also includes material-balance calculations relative to one of the oil horizons in the shallow zone. The Bureau of Mines believes that publication of the results of these analyses is a worthwhile contribution to the petroleum literature and of particular interest to the California industry."

Apr 1, 1947

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By Jr. Denton

This U.S. Bureau of Mines report presents the documentation for HEAPREC, a methodology for calculating reclamation performance bonds for cyanide heap leach operations. HEAPREC is a template developed for use with Lotus 1-2-33 release 2.01 or newer software. The report is presented in step-by-step "user's manual" format. Appendices contain detailed background and reference material on performance bonding, cyanide detoxification regulation, cyanide detoxification methods, general mine reclamation procedures, and an example bond calculation.

Jan 1, 1992

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations, Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral -art of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations. Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydrocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, .practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral part of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Develop a mobile manipulator that one person can use to lift and maneuver 50- to 600-pound loads. It can be used in maintenance shops and mines to reduce lifting accidents (Figure 1 and 2). Background Lifting heavy items is one of the leading causes of injury in the workplace. Mine Safety and Health Administration statistics showed that, in 2004, back injuries accounted for over 20% of all injuries (1,699 cases) and resulted in 110,000 lost days of work. Forty-one percent of those injuries resulted from materials-handling or maintenance activities.1 In addition to back injuries, lifting injuries include hernias, ruptures, sprains, and strains resulting from losing control of the item being lifted. Factors associated with accidents are weight of the item being lifted, awkward postures, inadequate handholds, and the working environment itself. High accident rates were noted when lifting items that ranged from 50 to 600 pounds, particularly in tight working quarters where maneuverability was critical. Research indicated that a mobile lifting arm would eliminate many lifting accidents in environments where other lifting devices (fork lifts, overhead cranes, mobile A-frames) would not be practical. NIOSH has built a first-generation mobile manipulator unit designed to be used on hard, level floors such as in a shop. The complexity of motion, number of moving parts, compact design, and design constraints of the manipulator required advanced computer-aided design work (Figure 3). As a result of the design work, thirty-eight claims are included in the patent applications. NIOSH will be conducting field trails and working with manufacturers to put the manipulator into industrial use.

Dec 1, 2006

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By C. P. Haller, S. J. Aresco, R. F. Abernethy

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash- softening temperature of ash, the free-swelling index, and the hardgrove grind- ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruc- tions issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the con- tractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal. The Government purchased approximately 5-1/4 million tons of coal in fiscal year 1953. In connection with these purchases, the Bureau analyzed 11,435 samples. These are published for the use of Government officials and the public. A series of publications has been completed on coal analyses by States, or, where production is small in any one State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications con- tain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals. Previous publications in this series are: Bulletin 516, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Years 1948 to 1950 Inclusive); Report of Investigations 4934, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1951); Report of In- vestigations 4972, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1952). Following are the Bureau of Mines technical papers published by States, with their numbers: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement 645); Pennsylvania Anthracite, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supplement 618); West Virginia, 405 and 626; and Wyoming, 484.

Jan 1, 1955

In 2006, a total of 7,178 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.2% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By Douglas W. Fuerstenau

This report presents the results of an investigation of comminution in tumbling mills. Five different topics involved with ball mill and rod mill grinding kinetics were studied and the results analyzed in terms of phenomenological size reduction and transport models. Continuous rod mill grinding was found to be characterized by high Peclet numbers which permit simulation to be carried out by several methods. The dry batch ball mill grinding of mineral mixtures showed that the breakage rates of the components were composition-dependent but time-independent and were normalizable with specific energy. Locked-cycle tests on mineral mixtures showed that a grinding circuit may take a long time to attain steady-state, during which time the composition of the mill holdings, and hence the breakage rates of the components, continuously changed. This study revealed that under plant conditions, grinding circuits can be in transience perpetually. The transport of mineral mixtures through drums was found to exhibit complex size and/or density-dependent segregation. However, the grinding media in a ball mill can eliminate such segregation, thereby simplifying the modeling of the continuous grinding of complex feeds. Wet batch rod mill grinding on single minerals divulged that the normalizability of breakage kinetics is valid for slurries of constant pulp density at different hold-ups but cannot be extended to slurries varying in pulp density.

Jan 1, 1983

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company's Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976