Search Documents

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By Steven E. Mischler, Jon C. Volkwein

A diesel particulate matter analyzer capable of direct, real-time measurement of engine exhaust particulate is necessary to effectively institute source control technology currently being used on diesel equipment and to ensure that the control measures are working. To investigate the potential of a differential pressure monitor to measure diesel particulate matter in undiluted exhaust, samples were collected from three different diesel engines-Kubota, Isuzu, and Deutz-running under 12 different RPM and load scenarios. These measurements were compared to elemental carbon concentrations in the sampled exhaust as determined by using the NIOSH 5040 analytical method. Elemental carbon is used as a surrogate measurement for diesel particulate matter. The results of the two data sets were then compared using a linear regression analysis. The coefficient of determination (or R2) was calculated to be 0.98, 0.94, and 0.74 for the Kubota, Deutz, and Isuzu engines, respectively. R2 values of this magnitude indicate that this method can be successful in estimating elemental carbon emissions in the engines tested. In addition, for replicate samples, the coefficient of variation ranged from 7.1% to 10.2% with an average of 8.5%. These data indicate that this method could prove useful to mechanics as they work to maintain engines and DPM control technologies.

By S. M. Moore

Technological advances in underground coal mining have reduced fatalities but may not have reduced worker exposure to cumulative injury risk factors. The objective of this study was to evaluate the prevalence of cumulative injuries before and after the implementation of technological advances in underground coal mining and to make a general cost estimate for these injuries. A previously published algorithm was utilized to identify cumulative injuries within the Mine Safety Health Administration (MSHA) database for two data sets: 1983-1984 and 2003-2004. For both, the following were determined: the number and percentage of cumulative injuries, the average days lost, the average age at the time of injury, the average years of experience and the general cost estimate by body part. The percentage of cumulative injuries remained largely unchanged (37 percent in the 1983-1984 period and 33 percent in the 2003-2004 period). The average number of lost days due to cumulative injuries increased (36±55 days and 62±82 days, respectively), which may have been due to the increased worker age (seven years older in the 2003-2004 period), increased length of employment (seven years longer in the 2003-2004 period) or other factors such as changes in medical practices. Cumulative injuries to the back decreased by 10 percent, while cumulative injuries to the knee increased by 8 percent. The reduction in back injuries may be due to the implementation of assist devices, while the increase in knee injuries may be related to kneeling/crawling in low-seam mines. Cumulative injuries were found to remain a major financial burden on the industry. Recently, National Institute for Occupational Safety and Health (NIOSH) developed tools to assist mining companies with incorporating an ergonomics process into their existing health and safety programs. The participating companies have reported tremendous success. Therefore, it is recommended that ergonomics processes be implemented as a means to systematically identify and address the root causes to cumulative injuries and ultimately reduce costs.

Jan 1, 2008

To reduce the respirable dust generated by auger-type continuous coal mining machines. The Approach: Use water sprays close to the cutting bits on the auger so that coal fragments are thoroughly wetted as they are formed to prevent dust dispersal into the ventilating air. How It Works: The "wet auger" system of dust control uses water sprays distributed on both shafts of auger type continuous miners. This approach has been tested underground by personnel of the Bureau's Twin Cities (Minn.) Mining Research Center on a Wilcox Mark 20 continuous miner, in a cost sharing contract with Buchanan & Sons Coal Company, Inc. Personnel of the Interior Department's Mining Enforcement and Safety Administration collected dust samples and analyzed the data. A test machine was fitted with six sprays on each auger (see Fig. 1). Water flow rates from 8 to 12 gpm at pressures from 90 to 120 psi, or about 8 gallons per ton of coal mined, were required. At these rates of water usage, mining personnel experienced no problems with work-

Jan 1, 1974

Mine fires pose a serious hazard to the health and safety of mine workers. They occur regularly and their effects can be devastating. Objective Provide mine safety personnel, MSHA, and equipment manufacturers with a comprehensive, up-to-date, and well-documented database of metal and nonmetal mine fire incidents in the United States from 1950 to 1984 and perform a statistical analysis of these incidents. The data-base is designed for use by mine engineering and safety personnel to aid in determining especially hazardous practices or conditions.

Jan 1, 1988

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006

By John J. Sammarco

Miners depend most heavily on visual cues to recognize underground mining hazards; consequently, illumination plays a critical role in miners? safety. Some hazards are located in the miners? peripheral field-of-view (10 degrees to about 60 degrees off-axis) or on-axis (0 degrees). The objective of this research was to determine if there were visual performance improvements when using solid-state cap lamps with light-emitting diodes (LEDs) as compared to incandescent light bulbs commonly used in miner cap lamps. Recent research has indicated that an increased short-wavelength content of the spectral power distribution of LEDs relative to incandescent lamps improves peripheral visual performance for low-light (mesopic) conditions. The visual performances of nine subjects were quantified by measuring the subjects? speed and accuracy in detecting floor objects located on axis and at ±20 degrees off axis. The objects were located near field (1.83 meters) and far field (3.66 meters). Upon presentation of the objects, subjects would count and point to each object using a red-laser pointer. The object detection response time and number of missed objects were recorded. The results of the visual performance comparison for an LED, a prototype LED, and an incandescent cap lamp are presented. There we no missed objects when subjects used the LED-based cap lamps but, there were three missed object occurrences when subjects used the incandescent cap lamp. The mean detection time when using the incandescent cap lamp was 55.3% greater than the prototype LED cap lamp and 43.5% greater than the LED cap lamp. It can be inferred from this data that the spectral distribution of LED-based cap lamps could enable significant visual performance improvements as compared to incandescent cap lamps1.

Jan 1, 2007

Reduce the respirable dust exposure of the roof-bolter operator when downwind of the continuous miner, particularly in mines where respirable dust standards are more stringent because of silica in the respirable dust. Dust Sources If roof-bolter dust levels are excessive, the bolter dust collector should first be checked to ensure that it is operating properly. (Technology News No. 219 provides information on how to spot and repair bolter dust collector problems). If the roof-bolter dust collector is operating properly and dust levels are still excessive, then the source is most likely a continuous mining machine operating upwind. In many sections, the roof-bolter operator must work on the return side of the continuous miner during part of the production cycle. In three-entry longwall developments with single split ventilation, this may happen as much as one-third of the time. Factors which pro-mote high quartz dust exposure are:

Jan 1, 1985

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

To improve a miner's chances for survival in an emergency by providing an improved self-rescuer device that functions in a toxic or oxygen-deficient atmosphere. The Approach: Development of a compact, lightweight apparatus which produces oxygen by using the wearer's breath in a chemical reaction. How It Works: The device is designed to cause the user's breath, which contains water vapor and carbon dioxide, to react with potassium superoxide (K02) to produce oxygen in quantities sufficient to sustain the wearer for one hour. The system is a closed circuit and does not depend on "screening" of noxious gases. To use the device, the miner opens the top and

Jan 1, 1974

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By Gerald T. Homce, James C. Cawley

Problem: CFOI and SOII data show that 2,287 U.S. workers died and 32,807 workers sustained days away from work due to electrical shock or electrical burn injuries between 1992 and 1998. Method: The narrative, work activity, job title, source of injury, location, and industry for each fatal electrical accident were examined. A primary causal factor was identified for each fatality. Results: Electrical fatalities were categorized into five major groups. Overall, 44% of electrical fatalities occurred in the construction industry. Contact with overhead power lines caused 41 % of all electrical fatalities. Discussion: Electrical shock caused 99% of fatal and 62% of nonfatal electrical accidents. Comprising about 7% of the U.S. workforce, construction workers sustain 44% of electrical fatalities. Power line contact by mobile equipment occurs in many industries and should be the subject of focused research. Other problem areas are identified and opportunities for research are proposed. Impact on Industry: Improvements in electrical safety in one industry often have application in other industries.

By J. C. Dumbrille

The following account of wining practices of the Kirkland Late Gold twining Co., (Ltd.), at Kirkland Lake, Ontario, is one of 4 series of papers being prepared by the United States Bureau of Mines on mining practices, methods, sad costs in various districts. The author has prepared this paper with the help and permission of J. B. Tyrrell and W. M. Sixt, the managing director and the mine manager, respectively. This mine is operating at a daily rate of about 150 tons.

Jan 1, 1931

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1983 was $361.3 million, an increase of $61.9 million over that of 1982. The increase reversed a downward trend that started in 1980 and established a new record high for value of nonfuel minerals in the State. Output of most nonfuel minerals increased to some degree with unit value increases creating the record-high value year. Cement, clays, lime, sand and gravel, and crushed stone were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; fourth in ferroalloys, dimension marble, common clay, and fire clay; fifth in bentonite and kaolin; and sixth in masonry cement and lime.

Jan 1, 1985