Search Documents

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By Stephen R. Iverson

The U.S. Bureau of Mines made an economic appraisal of the Buttermilk study area, Inyo County, California in October 1980. Results of surveys indicate no potential for metallic, non-metallic, or energy resources in the area. However, glacial till covering most of the area prevented bedrock examinations by the appraisal teams or earlier prospectors. No mining claims are known to be in the area. INTRODUCTION Present Studies The U.S. Bureau of Mines, Western Field Operations Center, searched county mining claim records and other data available concerning mineral deposits, claims, leases, production, and mining activity in the area. The Bureau conducted field work in October 1980 searching for prospects and claim locations. Fourteen reconnaissance lode and placer samples taken from the area were analyzed for gold, silver, and tungsten; a spectrographic analysis also was run on selected samples.

Jan 1, 1981

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By W. T. Abel

The rate of the steam-carbon reaction, which is of fundamental importance to coal gasification, was determined by passing steam over graphite specimens suspended in an electrically heated tube. The measurements were made at 1,900° to 2,400° F. and at steam-feed rates of 0.1 to 2.0 moles of steam per mole of carbon per minute. At the maximum steam-feed rate, the reaction rate of carbon ranged from 0.4 percent per minute at 1,900° F. to 7 percent per minute at 2,400° F. Up to about 2,200° F., the steam-feed rate had only a slight effect; above this temperature, it limited the reaction velocity when the final mole fraction of steam in the reaction products was much less than 1.

Jan 1, 1962

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By F. D. Everett

This report summarizes the results of a nationwide investigation completed in 1964 to determine the nonferrous base metal ore reserves and potential sources of ore and to evaluate criteria for their ultimate exploitation. Engineers of the Bureau of Mines contacted mining company officials, reviewed reports and Government records, and where necessary made personal appraisals in arriving at the results. The estimates are presented by metals in ores in geographic regions and include some of the problems affecting the reserves and potential sources. The recoverable metal in the measured ore category and in the total ore reserves was estimated as follows: [ ] At the 1963 rate of domestic mine production these total reserves would be adequate to provide copper for 62 years, lead for 121 years, and zinc for 42 years. Data also are given for gold, silver, and other coproducts. Reserve estimates greatly exceed those of previous investigations; some prior estimates of copper reserves are included for comparison (table 23). Projections of requirements for base metals indicated the United States will need approximately 45 percent more copper in 1970 and 110 percent more by 1980 than was consumed in 1960; similar projections for lead indicate increases of 20 percent by 1970 and 45 percent by 1980; zinc projections are 40 percent more by 1970 and 90 percent by 1980. Much of the production of gold and silver is a coproduct of base metals recovery and the projected need for the precious metals exceeds all the United States can produce. Some problems of the industry are mentioned. A graphic evaluation of the economic availability of the reserve and potential sources is shown.

Jan 1, 1967

By R. L. Marek

The number of persons fatally injured in the California petroleum industry, in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry--reduced personnel, decreased active field development, and curtailed production--have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period.

Jan 1, 1933

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By R. E. Brewwe

"INTRODUCTION Anyone who has had frequent occasion to compare methods of analysis and testing as employed in European countries with those used in the United States has felt the need of a table or graph giving the relationship between the units of measurement of finely powdered materials. Most of the few published comparisons include only two series of sieves and often require tedious interpolations to adapt the data of one series to the series more familiar to the reader. To eliminate such deficiencies, the author hopes that the discussion and comparison of fine-series sieve sizes presented here will conserve the time of interested research workers.ACKNOWLEDGMENTSThe author is deeply indebted to Virginia B. Strathearn, scientific aide, for help in compiling the information from the literature and to W. A. Solvig, senior chemist, for valuable suggestions in preparing the manuscript.SQUARE-MESH-SIEVE SERIES OF DIFFERENT COUNTRIESSieving analyses of powdered materials have been placed on a comparable basis in different countries by the introduction and adoption of standard sieve-scale series. Series of wire-cloth square-mesh sieves in common I oratory and industrial use include: Institution of Mining and Metallurgy standard laboratory screens (I.M.M.); British Standards Institution standard for fine-mesh test sieves (B.S. or B.S.I.); Tyler standard sereer-scale sieves; United States standard sieve series; Deutsche Industrial-Nermen (DIN); and the standard control sieves of the Association Francaise de Normalisation (AFNOR). With the exception of the I.M.M. series in which the opening is equal to the diameter of the wire, the general proportions of the various series of sieves are similar. The size of British and American sieves is designated by the number of meshes or openings per linear inch or, more recently, by the number of microns per linear sieve opening. In a technical sense the word ""mesh"" is meaningless, unless the diameter of the wire is also given, so that the size of the opening can be determined. On the Continent sieves are designated either by the nunber of Mesh per linear centimeter or by the number of openings per square centimeter."

Jul 1, 1944