Search Documents

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Tyler Acorn, Tristan Worsey

A dozer operator at a surface gold mine accidentally drove a D10 off the side of a highwall. The blade of the dozer caught on the lip of a catch bench 60 ft. (18.3 m), down stopping its descent. The operator scrambled to safety in fear that the dozer would not hold.

Jan 1, 2014

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By Milos Bila

The second half of 2008 and the first half of 2009 brought up important anniversaries. My old passport from Czechoslovakia has a stamp with date 10-10-1968 at 10:00 AM, the exact time I crossed the border between the former Czechoslovak Republic and Austria. This date has an important meaning because I could not come back to my country for the next 21 years. The 40th anniversary of Soviet led invasion, which took place on the 21st of August 2008, revealed some unknown and long time kept secret news.

Jan 1, 2010

By Mario Dobrilovic, Zvonimir Ester, Vinko Skrlec, Vjecislav Bohanek

The first public garage in the city of Dubrovnik has been built in highly urbanized area, on location Ilina Glavica. The excavation of the building pit has been done partly by construction machinery, i.e. by hydraulic hammer for excavations and partly by drilling and blasting. In the vicinity of the building pit there are houses, buildings and two schools. Drilling operations and blasting have been performed during the working hours while regular school classes have been held and activities in other buildings took place. The nearest structures are some 5 to 10 meters (16.4 to 32.8 ft) away from the building pit, which makes it even more difficult to perform blasting operations in the urban environment. For the purpose of determining safe and permissible oscillation velocity limits, i.e. the proportion of seismic effects of blasting, a trial blasting has been conducted. The permissible mass of explosive charge has been determined by original method respecting the requirements of existing standards (ISO 4866, DIN 4150, US BM 8507), which determine the permissible oscillation velocities in relation to their frequencies. According to measuring results of the oscillation velocity during the test blasting the design parameters of blasting field have been corrected and zones have been established within the excavation area considering the possible effect of blasting to the building pit environment. Further blasting operations have been performed in stages, in smaller blasting fields with deck charge within a blast hole while respecting the requirements of the transport possibilities for the blasted rock mass within the building pit and performance of control measurements of oscillation velocity for each blasting. Through application of all the protection measures, design solutions and systematic control of performance of activities the complete excavation by blasting has been completed without any damage on neighboring structures/buildings. This article presents these solutions and methods for reduction of seismic impact of blasting to the environment.

Jan 1, 2009

By B Kniivila, A B. Andrews, T Lerick, Keith Jansen

Minntac Mine is a large, open pit taconite mine located at the center of the Mesabi Iron Range in northern Minnesota. The planned development of the Mine in the direction of nearby communities prompted a comprehensive study of off-site blast effects that resulted in numerous refinements in blasting practices.

Jan 1, 1984

By Don Larson, Gordon Coleman

The United States Department of Energy, through its contractor Lawrence Livermore National Laboratory, has entered into a contract with Alpha-IRECO, Inc. for the emplacement of approximately 2.9 million pounds of a 50% RX-MD emulsion 50% ANFO blend into an underground chamber for initiation to produce the 12 trillion caloric equivalent of 1,000 metric tons of TNT. The detonation will be closely monitored to determine the characteristics of a large chemical explosion for comparison with data collected from previous like-sized nuclear events in the same location. This data will be shared with former Soviet block countries to facilitate enforcement of the various non-proliferation treaties currently being negotiated between the countries.

Jan 1, 1994

By Manuel Calderón

Chile is responsible for 30% of the global copper production; the world ́s largest. However, significant challenges are faced in this industry; declining grades (1.13% in 2002 to 0.61% in 2015), high cost of energy, scarcity of water, and environmental concerns. Mining trends suggest the future of the industry will be focused in the underground space, specifically due to the depletion of economically viable surface mineral deposits. For example, the largest block cave mineat Codelco ́s Chuquicamata mine is expected to reduce energy costs by 50% and dust emissions by 97%compared to the open cut mine. To access these underground deposits, critical infrastructure is required; horizontal tunnel developments, extraction levels, vertical raises, and ore passes with the on-time delivery of the highest quality outcomes being a requisite for successful project delivery (Lift 1 of 3 at Chuquicamata Underground has over 1000drawbells).One aspect that makes this scenario even more challenging for deeper underground operations is the increased risk profile (people, equipment, and geotechnical) that forms part of the general environment. Furthermore geotechnical risks should be considered and they include rock burst and windblast. The safe interaction with this environment must be sustainable throughout the full life of the project. This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important draw bell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

By K. Best, D. Conn

The US Army Corps of Engineers KY Lock Project in western Kentucky presented the blasters and vibration consultants with a set of unique challenges. The blasters on this project were faced with difficult geology and joint set orientation and sequencing of blasts opposite from what the explosive engineer/blasting specialist had recommended. Combining these issues with strict vibration and air overpressure specifications, blasting as close as 7 feet (2.1 meters) from a new lock wall, site topography that influenced the air overpressure, limitations on seismograph geophone placement that led to anomalies in seismograph recordings; surprising lessons were learned by everyone involved in the project and it is the authors’ goal to share this valuable information with everyone in the blasting industry.

Jan 1, 2024

By Johan Hillman, D. Scott Scovira, Thomas Gustavsson, Alexander Bihlar

Hydrogen Peroxide Emulsion (HPE) explosives are an alternative to conventional commercial explosives. HPE does not contain nitrates or ammonia thus eliminating post-detonation NOx fumes and aqueous nitrate discharge. Production of HPE is less carbon intensive than industry standard ammonium nitrate-based emulsions (ANE) and employment aligns with end users seeking to meet Scope 3 ESG emission targets. Swedish tunneling contractor Implenia Sverige was awarded the Högdalen Depot Expansion Project by the City of Stockholm. Implenia Sverige partnered with Hypex Bio to be the first to pilot the application of a nitrate-free explosive system in a large-scale civil construction tunnel. The purpose of the joint project was to evaluate the operational suitability of replacing conventional nitrate-based bulk explosives with HPE in a large-scale tunnelling project. When the project commenced in September 2023 both standard nitrate-based emulsions and HPE emulsion were used in parallel (Tunnel Right and Tunnel Left) to enable operational, performance, and environmental comparison. Identical drill patterns and initiation techniques were applied to both tunnel headings. Performance data collected included round advance, usage, and perimeter quality. Implenia managed all drilling and charging operations and Hypex Bio provided technical support, including technicians and chemists. HPE is viscous and pumpable using conventional emulsion pumping delivery systems. Variable density functionality enabled loading different charge weights into cut, lifter, production, and perimeter holes. The primary rock type was hard sedimentary gneiss with approximately 150 MPa [21,755 psi] Uniaxial Compressive Strength (UCS). Fracture systems with infilling occurred in both tunnel directions. Rock quality factor was “Good to Very Good” on the RMRb (Rock Mass Rating) scale. Epiroc Boomer rigs were used to drill rounds averaging 4.9 m [16 ft] deep with high accuracy and precise reference positioning.

Jan 26, 2026

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Tom C. Palangio

Commercially available online particle size analyzers (OPSA) are in their third decade of development (Palangio, T.C., 1985), (Franklin, J. A., Maerz, N.H., 1987), (Maerz, N.H., Franklin, J.A., and Coursen, D.L., 1987). The installed base of operating analyzer numbers is in the hundreds. This paper takes a look at five critically important relationships that users have discovered through the use of OPSA systems. The two key attributes of these systems are: 1) consistency and, 2) historical context compared with traditional practices.

Jan 1, 2016

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Scott G. Giltner, Terry Millar, Ben Bringhurst

"Kennecott Utah Copper (KUC) Smelter scheduled a rebuild of their flash smelting furnace forSeptember, 2014. KUC’s goal in this project was to reduce the rebuild time from 65 to 55 days by using explosives to break the matte and brick layers of the uptake shaft and hearth sections of the furnace. Previous rebuilds had employed the slower technique of mechanical breakers to remove the matte and brick layers which took 22 days. KUC has many years of experience in removing slag from the uptake shaft, but they had never used explosives to remove the hearth. As far as KUC was aware, no other smelter operation had attempted a hearth removal in this way."

Jan 1, 2016

By Mick Fritz, Ryan Gilmore

The Center for Disease Control [CDC] is in the midst of a twenty year project, part of which includes demolishing existing buildings and erecting taller, more modern structures within the same foundation foot print. Controlled Blasting Inc, a large and experienced construction drilling and blasting company in Metro Atlanta, was contracted to provide the drilling and blasting for the new building foundations. Working on a construction site, in this type of environment, creates many challenges for the drilling and blasting crews.

Jan 1, 2008