Search Documents

By C. T. Aimone-Martin, V. L. Rosenhaim

The response of two structures to blast-induced ground vibrations were evaluated and compared in order to quantify the impact of different blasting operations, hard rock and soft rock blasting, upon the structures movements. The first instrumented structure was a residential type, located in the operational area of a coal mine, were blasting is conducted in soft rocks, such as siltstone and coal, with compressive strength ranging from 20 to 50 MPa. Blasting is characterized by low benches, with hole lengths averaging 5.5 m (18 ft) and low powder factors, 140 to 210 g/m3 (0.236 to 0.354 lb/yd3), resulting in very little horizontal movement of the rock during the blast. The second structure was a commercial building, located in a basalt quarry (compressive strength between 109 and 180 MPa), where blasting is conducted in 12 m (39.4 ft) benches with powder factors ranging from 200 to 350 g/m3 (0.337 to 0.590 lb/yd3). Velocity sensors were placed on the structure walls to measure wall displacements and calculate blast-induced strains in the walls, and these results were compared with the driving ground excitations. The calculated strains were compared with the limits of rupture of the cement grout used as mortar between bricks and as wall coating, considered to be the weakest material in the structure composition. The blast-induced response of existing cracks in the structures were also measured using displacement gages and compared to the daily influence of weather fluctuations, such as changes in temperature and humidity, on crack movement. The results show that for the same levels of ground motions the structures present different movement, resulting in distinct levels of induced strains on the walls depending on the geology. The influence of long-term temperature and humidity variations on crack movements on both structures is very similar, during the same seasons of the year. Crack response to long-term weather changes is 2.5 to 3.5 times greater than blast influences.

Jan 1, 2015

By Jianping Li, Ernesto Villaescusa, Kelly Fleetwood

During blasting, stress waves propagate through a rock mass, inducing stress and strain changes. This applied deformation affects intact rock, existing discontinuities, mine excavations, and engineered structures in the proximity of the blast. Traditionally in blasting, stress waves are quantified in terms of peak particle velocity (PPV) or peak particle acceleration (PPA), based on the method of measurement and the specified allowable tolerances. During analysis, the peak particle motion is coupled with an explosive source through various scaling laws to develop rock-specific attenuation relationships. Some studies have expanded this practice to the development of damage threshold values based on measured or predicted peak particle velocities. PPV-related thresholds are generally based on empirical models, where observation of overbreak, cracking, or fall-off are used to quantify damage. This method is often paired with the application of elastic plane wave equations to calculate the blast induced strain or the PPV threshold for tensile rock failure. Other factors that must be viewed critically in such models are the methods used to collect and analyse blast vibration data and the application of inappropriate vibration attenuation relationships.

Jan 1, 2009

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By Alastair Torrance

The performance of commercial explosives is clearly influenced by the conditions under which they are used. Mining companies are supplied with Technical Data Sheets which provide details about explosive properties and its suitable application. These are generally produced using laboratory techniques which may not accurately reflect the quality and performance of the product in the field.

Jan 1, 2013

By Harry Verakis

Flyrock is the second leading cause of all blasting related injuries in surface coal, metal and nonmetal mining operations. It is also a primary cause of property damage, monetary losses and “near misses.” For the period 1978 to 2008 flyrock accounted for 11.6 percent of all blasting-related injuries in surface coal, metal, and nonmetal mines. A large amount of published material has been published on the safety hazard of flyrock, on ways to predict how far rock will travel from a blast, as well as ways to protect mine personnel and neighbors from flyrock. However, flyrock incidents continue to occur resulting in fatalities and “near misses” that could have caused fatalities. It was only good fortune in some instances that no one was in the mine's parking lot or other unprotected area when flyrock rained down or in harm’s way when a large rock punched a hole in the roof of a building or other structure.

Jan 1, 2011

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By C. E. Johnson, R. L. Bauer, E. M. Johnson

In industry, the strength of a blasting cap is often equated to the type of explosive it can detonate. Comparable cap strength is becoming less important as nearly all caps manufactured today can initiate high explosives, such as primasheet, with ease. Previous studies were conducted to assess the quantity of energy released by various detonators into the directional propulsion of the detonator’s casing. However, the question of how much of this propulsion energy is needed to initiate an explosive remains unanswered. This study will assess the fragmentation size and velocity needed to initiate a high explosive when they are not in direct contact. For this study, primasheet was used as the main charge as it is relatively insensitive and can be situated in different positions relative to the detonator. Electric, non-electric and electronic detonators were used to evaluate initiation potential. The primasheet is observed in response to being in contact with a detonator, and not in contact with the detonator at various distances and angles. This allowed the quantity of energy transferred into the primasheet to be observed and for the initiation of the sheet to be recorded using high-speed video. This study will report the energy necessary to initiate the primasheet at various distances and angles from the charge from a number of widely used, commercial, hot wire blasting caps.

Feb 6, 2023

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014

By Auã Kiahla, Tomi Kouvonen, Vinicius Miranda

Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper

Feb 1, 2020

By Rachel L. Bauer, Catherine E. Johnson

Explosive demolition involves first, the use of cutting charges to sever a column and second, kicker charges to move it out of alignment. Dynamite is the traditional explosive used in kicker charges as it is inexpensive, easy to initiate, and has a consistent track record of use. Dynamite, however, has health concerns in handling, fragmentation concerns from direct contact on the beam, and availability concerns due to being manufactured at only one location in the continental United States. Recently, water-cased kicker charges have been used in industry, and research has shown that a reduced dynamite mass is possible due to the added confinement, for energetic performance, and the incompressible fluid, which aids in the transfer of explosive energy into beam movement. This research will compare two different explosives, an emulsion (DYNO AP), and binary (HELIX), to dynamite for use in kicker charges, both with and without water-casing. Emulsion is commonly used in rock blasting to create a large push or throw due to its high gas volume production which could translate to kicker charge movement. HELIX is a binary explosive commonly used by the military in breaching charges with water backing. Experimental tests placed kicker charges at the base of a hanging steel column, modifying the ballistic mortar test used to determine explosive power. The study shows that water-casing effectively reduces air overpressure and enhances explosive performance. Among the tested explosives, HELIX showed the most substantial improvements with a 1.8 dB reduction in air overpressure and a 3.2 m/s (10.5 ft/s) increase in column velocity when water-cased. Dynamite and emulsion also benefited from water casing, with decreases in air overpressure (1.1 and 0.7 dB respectively) and increases in column velocity (1.1 and 0.7 m/s (3.6 and 2.3 ft/s) respectively). This research also shows that emulsion is a viable replacement for dynamite in demolition projects, performing similarly in both traditional use and water-cased charges.

Jan 21, 2025

By Douglas Bartley

As the economy continues to slowly recover, our industry continues to finds ways to increase productivity while being forced to cut costs. The drilling and blasting process is the starting point of any aggregate or mining process. Many people refer to it as the “Primary Crusher” as it will always be more efficient to crush rock with explosives energy than it will be mechanical energy. It is the more efficient use of this energy that is addressed in this paper.

Jan 1, 2012

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By Randall M. Wheeler

Computer analyses of single hole signatures are often used to help blasting operators predict the type of ground vibration effects that may be produced from production blasts incorporating various delay intervals. Frequency analyses of single hole waveforms and subsequent multi-hole waveform simulations can allow an operator to determine the best type of delay intervals to use in order to minimize low frequency ground vibrations.

Jan 1, 1989

By N. Rouse

Underground raises and slots are a vital part of underground blasting operations. Raises and slots are vertical shafts or openings used for ventilation, ore passes, or creating voids in stopes. In the author’s experience, raise and slot designs can vary significantly from operation to operation or even within a single operation, sometimes for reasons unknown. The results of the various designs can differ depending on drilling accuracy, geology, and the explosives used in the design. The purpose of this paper is to summarize the recommendations found in published literature on raise and slot design in one document, while incorporating some of the author’s own experience with optimizing raise and slot designs in underground operations. Some inspiration is also included from burn round designs; small versions of raises drilled horizontally in development blasting rounds. This document includes discussion points on drillhole diameter and depth, pattern design and relief requirements, explosive types and loading recommendations, and timing. Ultimately, this document can be useful to those looking to design a raise or slot blast for the first time or for those looking to improve on the results from the raise and slot blasts used at their operations.

Jan 1, 2024

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023