Search Documents

By Rachel E. Gooding, George C. Emmett, David R. Bradley

The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T) is using a probabilistic risk assessment (PRA) approach to evaluate the risks from terrorist use of explosive materials against the Homeland. A similar approach is currently being used to evaluate the risk from terrorist use of chemical, biological, radiological and nuclear materials.

Jan 1, 2017

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By Iván Aguirre Palacios, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, mining operations seek to be competitive in the market. To achieve this, one of the relevant factors is to maintain and improve the productivity of the extractive processes, mainly the loading from the point of opening of the mineral bodies. To do this, many techniques suggest reducing production costs, with the first opening of your free-face up raises. However, there are different ways to carry out these open-face raises up opening processes, where the balance of costs and construction time must be well planned to meet production plans. Operationally, there are different techniques for its construction, the most common being Blind-Hole up Raises and those with drilling with current production equipment that operates mining operations. This study shows a methodology and the results of the implementation of access stack drilling with production drilling rigs for a maximum height of 15 m with electronic detonators in production blasting. Within the methodology used, Qa/Qc processes were considered in cargoes with explosives, instrumentation for monitoring (vibrations), VOD registration, among others. As a result, of a total of 12 raises up blasts, construction time was reduced by 45% and the cost of drilling and blasting (P&V) was reduced by 50%, for up raises with a maximum height of 15 meters. Regarding the efficiency of the heights, this was 97% compared to the planned drilling design.

Jan 26, 2026

By Frank Barker

Mining operations present a very different environment to the suppliers of explosives, initiating systems and services, both on surface and underground. Typical hazards include underground movement, air quality, ground stability, moving equipment, and the use of explosives. As contractors to the mining industry we do not have management control over the environment in which our people operate. The hazards and consequent level of risk that our people are exposed to in some mining operations are significantly higher by orders of magnitude than in a normal factory environment. Orica Explosives (and other Explosives suppliers) are continually and increasingly identifying opportunities to partner with customers by adding value through the provision of services leading to a reduction in total mining costs. These services include the provision of a bulk underground loading services, delivery of product into underground magazines, magazine management, value added blasting, conversions, rock-on-ground contracts, and blast management programs.

Jan 1, 2000

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

By Amos Bryant, Jesse Davis

This paper compares the predictions of the latest Institute of Makers of Explosives Safety Analysis for Risk (IMESAFR) model versus physical test data recovered from ISO-1 and ISO-2 tests in Woomera, SA. ISO-1 testing included placing 1054 kg (2324 lbs) of ANFO (ammonium nitrate-fuel oil) inside an ISO container on a flat bed truck. ISO-2 testing was identical except the NEW was 4000 kg (8818 lbs). The IMESAFR predictions are based on model runs using the best match available to the actual donor type involved in the test. This type of debris analysis is not the standard output of IMESAFR, as the program is designed to assess the probability of human fatality. However, all of the IMESAFR predictions presented were obtained from the use of the actual model equations and algorithms without adjustment. Test results from ISO-1 and ISO-2 will be presented as well as findings from the comparison between model results and actual explosive results from the ISO testing efforts.

Jan 1, 2010

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Zheng Shuangying

The vibration effect of the buried oil pipeline caused by tunneling blasting affects the pipeline safe transportation, tunnel construction schedule and its construction cost. The dynamic response characteristic of the buried pipeline under blast loads is the foundation of designing blasting scheme as well as the prerequisite to pipeline safety. Taking the blasting engineering of Xiannvyan tunnel passing through a buried oil pipeline of the high-speed railway from Xi’an to Chengdu as the background, according to the space relation between tunnel and pipeline as well as the charge structure of V-cut blasthole, the 3D non-linear dynamic finite element model of tunnel-pipeline was established in the light of the equivalent explosive. The vibration response of the ground surface over pipeline resulting from V-cut blasting was simulated by LS-DYNA finite element program. Comparing with the measured vibration velocity waveforms in site, the accuracy and reliability of the numerical model are well verified. On the base of the simulation method, the coupling dynamic response characteristic between buried oil pipelines and soil was further studied and the Von-Mises stress distribution of pipeline wall was obtained. The safety of buried oil pipeline was quantitatively analyzed through the inside stress data of pipeline given by the simulation calculation above. The analytic results show that the maximum vertical vibration velocity of pipeline on the interface between pipeline and soil is 1.62~5.07 times as large as that of soil. When the buried pipeline is located over the tunnel and 13 m (42.6 ft) away from tunnel, the maximum vertical vibration velocity of ground surface caused by V-cut blasting with charge weight 17 kg (28.6 lb) is 3.17cm/s (1.25 in/s) and the vertical peak vibration velocity of pipeline top is about four times as the ground location directly above the pipeline. Meanwhile, the peak dynamic stress of the buried pipeline caused by blasting vibration is only 2.35% of the allowable stress of steel pipeline. The maximum superimposed stress of the blasting dynamic stress and the hoop stress produced by the pipeline internal pressure is 242.56 MPa (35 180.36), which implies that the buried oil pipeline is completely safe under the conditions of the given tunnel blasting scheme.

Jan 1, 2015

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Dominic C, Gregory B. Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction

Feb 1, 2020

By Theirry Bernard

The era of non-electric systems as an initiating system has revolutionised the blasting world by introducing a very safe initiating system that is reliable, with initiation sequence possibilities that are superior to those of purely pyrotechnical or electric systems. Electronic initiation has brought with it accuracy, programming and controls that were lacking in the non-electric systems. However, it has also led to a certain degree of complexity, which works against user-friendliness, sometimes introducing a few constraints that are balancing out the intrinsic performance of electronic detonators. The introduction of a hybrid initiation system, Electronic and Non Electric, offers accuracy, and flexibility that were lacking in non-electric systems, whilst removing the inherent complexity of electronic systems. This paper endeavours to summarise the advantages and disadvantages of non-electric and electronic initiation systems that have been recorded after years of experience on site. The paper will then describe how a hybrid system only keeps the advantages whilst eradicating the disadvantages, via a case study.

Jan 1, 2007

By Catherine T. Aimone-Martin, Brent Meins

Blast vibration monitoring for buried pipelines is typically conducted at the ground surface with a shallowly buried geophone. In many jurisdictions across the U.S., blast-related vibration limits set for pipelines are dictated by surface measurements and do not consider the significant reduction of PPV amplitudes acting on the pipe at depth. This study involved a vertical array of geophones deployed in drilled holes at two blasting sites of the Loop 202 South Mountain Freeway construction project in Phoenix, Arizona. City of Phoenix pipeline engineers were concerned that blasting would damage an aged 48-inch (122 cm) prestressed concrete cylinder pipe (PCCP) that serviced water for South Phoenix

Jan 1, 2019

By E Novikov, D Johansson, U Nyberg, A Beyglou, N Petropoulos

Fragmentation is an important factor for improving downstream processes in mine operations. Six trials have been conducted at the Aitik copper mine to investigate the effect of ultra-short inter-hole delay times, i.e. smaller than 1 ms/m of burden, on fragmentation. Swelling, MWD data, and crusher efficiency were also evaluated for trials. According to the results, the effect of examined short inter-hole delay times, i.e. 0.14 to 0.86 ms/m of burden, on fragmentation was found to be marginal. Delay time of 0.43 ms/m of burden resulted in slightly finer fragmentation and larger swell; however, the effect of short delays was overshadowed by the effect of small variations in specific charge.

Jan 1, 2014

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By Alvin D. Christmas

The missing link is a connector between the congested downtown area of Knoxville, Tennessee adjacent to the former World's Fair site, the I_40 I_75, and Western Avenue traffic arteries. This connecter was designed to accommodate the 37,470 motorists who presently travel through these highly congested narrow paths to be replaced by the 21.8 million dollar Henely Street Connecter. All construction and blasting was to take place while existing traffic was re_routed so as to allow access between the downtown area and the vital interstate corridor. To avoid major traffic problems, the project was to be accomplished in three phases: (1) the Western Avenue viaduct demolition; (2) two new viaducts to be constructed; (3) the open box cut at Henely Street next to the L & N Depot. Due to the past attempts by the Fort Sanders Community Home Owners group and the Historical Society to stop the Henely Street Connector, this project involved a very comprehensive blasting damage control program with special provisions of .5 inches per second measured at the foundation of the closest structure.

Jan 1, 1995

By Erik Nygaard, Klaus Voges

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small borehole diameters increasing amounts of toxic fumes (CO, NO and NOz) can be formed. In underground blasting, problems can also occur with reduced visibility caused by unreacted ammonium nitrate and overall composition of the detonation fumes. ANFO is made by mixing Ammonium Nitrate Porous Prills (AN-PP) and fuel oil. We have measured velocity of detonation (VOD), toxic fumes and visibility after blasting of ANFO in 54x2 mm steel tubes, and the differences are remarkable: By using an AN-PP grade developed for underground blasting and small diameters, the following can be obtained:

Jan 1, 2001

By Robert C. Friend

On-the-job and "hands-on" training programs which attempt to train newcomers to blasting with instructors whose only qualification is their experience can easily miss the boat. Organized training programs which utilize competent instructors and a well developed format are necessary if we wish to provide a meaningful program of instruction, But, let's not go overboard and attempt to provide a level of training which goes far beyond the scope of the worker's duties and responsibilities, and "need to know",

Jan 1, 1980