Search Documents

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By Virendra Singh

The load settlement behaviour of single pile or pile group may be obtained using computer based methods such as the finite or boundary element techniques. An alternative method of obtaining the vertical soil stresses adjacent to the Pile is presented Based on calculated stresses consolidation settlement for Piles foundation is obtained. This approach may be computationally more attractive than the more general finite or boundary element techniques.

Jan 1, 1996

By James R. Gingery, Byron Foster, Bret Lingwall

While microzonation and setbacks are the typical mitigation for structures exposed to surface fault rupture hazards, lifelines and lifeline facilities are not easily relocated to avoid faulting. In these cases, other remedial measures including ground improvement may be warranted. Deep soil mixing ground improvement was used in this case to mitigate surface fault rupture and liquefaction hazards for a pump station at a wastewater treatment plant with wet wells up to 36-feet (11-m) deep. Paleoseismic field investigations were performed to characterize the site, then deterministic and probabilistic fault rupture displacement estimates were made and used to develop design scenarios. The fault rupture mitigation design consisted of a solid block of DSM encompassing and protecting the pump station and its wet wells. Three dimensional soil-structure interaction numerical modeling of the fault rupture scenarios was performed as part of the design. The analyses showed the fault rupture displacements could be diverted by the DSM and that satisfactory structure performance could be achieved. The design required construction of a large 100 percent replacement ratio block of DSM with a compressive strength of 500 psi. Aspects of construction of this DSM block are discussed.

Sep 8, 2021

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By Hui Yongning

This paper presents a simulating test of constitutive relation of soil anchor in laboratory and puts forward a new plastoelastic mechanical model, on which a new calculating formula of elastic and plastic limit bearing capacity for soil anchor is suggested and two engineering projects verify that this method is adaptable.

Jan 1, 1991

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By James J. Neate

The augered cast-in-place pile system came into use in the late 1940's where various techniques were tried using pressure grouting methods. In the early development stages some piles were installed using the preplaced aggregate concrete system. As development continued it became more apparent that placement of coarse aggregate was more costly than making a pile out of a cement and sand mixture only. Various techniques were tried consisting of pumping structural grout into an open hole through a pipe left in the bottom of the hole, drilling or driving a pipe in close proximity to the tip elevation of the auger or in working a pipe down adjacent to the auger fluting. For these techniques the pipe was usually withdrawn after grout appeared at the surface. In 1951 a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The plug or lead bit was removed by grout pressure and this would be an expendable item for each pile placed. The patent was granted in 1956 and patent rights were assigned to Intrusion-Prepakt, Inc. Shortly thereafter other contractors were granted licenses to utilize the system. Patent coverage expired in 1973 and this method now is in the public domain. Today the method is in wide use throughout the world and is particularly well accepted in Japan and England.

Jan 1, 1988

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991