Search Documents

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923

By J. L. Bowlby

OWING to the pressure of routine analyses at the laboratory during the past year, work of an investigational nature on water problems has been greatly curtailed. Favourable reports by the boiler inspectors indicate that the operators are giving satisfactory attention to feed-water treatment at the several . power plants. Some of the operators prefer lime and soda, others the phosphate and soda treatment. Springhill is still on the same commercial treatment as they were using last year, and satisfactory results are being obtained. This individual preference for a particular treatment, although it may be different for feed waters of similar nature, indicates that so long as proper conditions of alkalinity and concentration are maintained within the boiler, it is immaterial what chemicals are used in the treatment. This statement refers, of course, to the low-pressure boilers. In high-pressure boilers, a treatment such as lime and soda cannot be satisfactorily employed, on account of the precipitated calcium carbonate unduly increasing the amount of suspended matter. Only one case of impending trouble was reported during the year. That was at Seaboard, shortly after the new unit was placed in operation. Dissolved oxygen, considerably in excess of the permissible 0.030 cubic centimeters per liter, was detected at various points on the feed line. It was suspected that a de-aerating heater was being operated at too low a temperature, and chemical tests, made before and after the necessary adjustments, proved that this was the source of the trouble. While it has been impossible to give mine waters the attention they require, progress can be reported in the work carried out by the Mechanical Department. Past investigation of the action of mine water on various acid-resisting alloys is now bearing fruit, and it can safely be said that repair work on mine pumps has been reduced by nearly one-half.

Jan 1, 1938

By Inga Tuzovskaya1i

Three types of gold species were observed for gold-zeolites, prepared by reduction of ionexchanged Au species in a series of zeolites: (i) Au3+cations, (ii) neutral Au0 n or charged Aus+ n clusters suggested to be inside the zeolite channels, (iii) Au nanoparticles with diameter varied from 2 through 20 nm located on the external surface of zeolite microcrystals. Contribution of the gold species formed in zeolite after the ion exchange was found to depend on zeolite type, acidity of zeolite, temperature of reduction and time of storage of the exchanged and reduced Au-containing zeolites. Au3+ ionic species and clusters Aun were formed after the ion-exchange procedure (in contrast with the familiar production of Agn in same zeolites). Gold nanoparticles were observed only as the result of reduction of the Au-exchanged forms at elevated temperatures due to reduction of Au3+ species and aggregation of clusters.

Oct 1, 2003

By Mauro Chiesa

A. New Dictionary, Since 2007/8 Traditional concept of ?cycle? is dead A dearth of projects AND good metal prices suggests otherwise In a depletion-business, good times for any greenfields in 2-3 yrs! ?Balance? sheet means quality assets = quality capital So, de-risk the assets, and ration the capital ?Replacement costs > historical costs ?Discounted assets depleting; replacement costs need self-financing (FCF) ?Public-sector slows permits, avoids assets and wants more of FCF ?Capital ?markets? are now ?market fragments? ..and? ??Shareholder? has changed from ?growth? to ?income + performance? ?Higher search costs, higher capital costs and higher cost of capital

May 1, 2013

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

NANA Accepts Mining ­ 1974 - Leadership presented mining option to people ­ Community meetings; recognized need for cash economy ­ 1979 - Poll shows consensus in favor of mine development ­ 1980 - Shareholders approve mining; Congress approved land selections

May 1, 2002

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007

By Roger V. Pierce

"WITHOUT mineral wealth, modern man would not exist. True, man could survive on a stone-age basis with an average life expectancy of, say, 25 to 30 years -once he got past infancy.However, no metal would tip his arrow in a hunt for protein; no steel plough would break the soil for the organized planting of seed; and no coal, nor oil, nor natural gas nor uranium fuels would pro-vide him with light or beat or safety from either beasts, or other men, or an unkind nature that threatened him and his family.Modern agriculture, fishing and forestry represent the other three wealth-producing industries. With-out metals, non-metallics and energy minerals, however, it would be impossible to fit any of these to man's modern needs."

Jan 1, 1967

By G. R. Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM's goal is to improve the mining industry's performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move external verification of their performance in 2007. The initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector will be examined.

Jan 1, 2007

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By Brian Lewis

"IntroductionThe leaching method selected for the dissolving of uranium ore depends in part on the physical characteristics of the ore, as well as the uranium mineralization. There are two main methods of leaching employed in uranium circuits in North America, one being ""Carbonate Leaching"" on sandstone, and pitchblende type ores, and ""Acid Leaching"", on quartzite type ores.This chapter deals with the acid leaching of uranium ores found in the Elliot Lake area, using sulphuric acid, for the leaching reagent, and ""pachucas"" for the contactor.The basic leaching process involves the pregrinding of the ore and the mixing of the ore with hot sulphuric acid, the mixture is air agitated, the air being used to oxidize the ore as well as produce agitation. The chemical reaction is as follows: Uranium Oxide + Sulphuric Acid = Uranyl SulphateThe following equations show the actual dissolution of the ""Hexavalent Uranium"", which show that more than one ion or complex of uranium is possible.Uranium DissolutionsI. UO, + 2H-(UOJ + H,O2. (UO,) + SO, = -UO, SO, (Uranyl Sulphate)3. UO, + SO,-(UO, (SO,),)=4. (UO, (SO,),)= -(UO, (SO,),)'Test work carried out in the laboratory as well as in the plants has determined the most efficient methods of extracting the uranium from the ore. A very important factor that has to be determined during initial test work are the amount of acid consumers in the ore. Within the Elliot Lake orebodies are minerals such as chlorite schist, diabase, and basement material, all very high acid consumers, consuming up to 1000 lbs. of acid per ton of ore. Of these minerals only the chlorite schist contain any uranium at all.The following are the operating parameters that have to be controlled in the plant:I. sulphuric acid concentration2. temperature of the mixture3. agitation4. liquid solid ratio5. reaction time6. particle size of ground ore"

Jan 1, 1989

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003

By Enzo Angeles, Desmond Nanchengwa, Lee Julian, Julian Ruiseco

Since the early 1980s, surface hard-rock mining companies have searched for a blast movement model to enable grade control optimization efforts. Significant time and money were spent attempting to create blast simulations to aid post-blast grade control. Despite nearly 40 years of effort, practical blast movement models remained elusive until computing power reached levels that make real-time simulation possible. From the mid-1990s, mines have been creating in-situ grade control polygons and translating the polygon nodes horizontally to account for blast movement. In many cases, objects are placed in the blast volume and located post-blast to provide local vectors for these node translations. This method was always a compromise between practicality (2D) and reality (3D), but it was the only viable solution that matched the needs of operations. This study considers 21 blasts and evaluates the incremental value achieved by new processes unlocked through 3D modelling, while investigating challenges, limitations, and opportunities for each method.

Jan 1, 2023

By John S. Stevenson

"Although we have no uranium- producing mines as yet in British Columbia, uranium, associated with gold and cobalt, has been found in two deposits in amounts such that the combined value of the metals not only warrants the further exploration of these deposits, but also encourages the search elsewhere in the Province for other similar deposits.Where uranium-bearing veins have been found in British Columbia, the uranium mineral is the crystalline variety of uranium oxide, uraninite, rather than the massive, non-crystalline variety, pitchblende, such as found in the Great Bear Lake deposit and in other similar deposits along the southwestern margin of the Precambrian shield.The principal occurrences of uranium known so far in British Columbia are associated with bodies of granodiorite and quartz diorite along the eastern side of the Coast Range belt of batholiths. In this part of the Province, interesting amounts of uranium occur on the Gem property in the Bridge River area and on the Victoria property south of Hazelton; and smaller amounts occur on the Red Rose, Rocher Debouze, Delta, and Ohio properties, also south of Hazelton. At the Gem and the Victoria, the uranium mineral, identified as uraninite, occurs in deposits that also contain abundant cobalt-nickel sulpharsenides, and molybdenite.At these properties, the uraninite occurs as clusters of small black crystals of sub-metallic lustre that may be seen upon careful -searching of a highly radioactive specimen with a hand lens. Under the microscope, the uraninite is seen to be in the form of cubes or modifications of cubes that may occur as individual grains widely scattered throughout the gangue or may be gathered into clusters of several grains. The grain size of the uraninite is in general small. Although a few clusters of grains are up to about 10 mesh in diameter, the individual grains, whether in clusters or widely disseminated, are rarely more than 400 mesh in diameter."

Jan 1, 1950

By S. R. Izatt

The use of MRT, a highly selective separations technology, has long been demonstrated to be a cost effective, efficient, and environmentally sound process for extraction of a wide range of anions and cations that are commonly found in copper electro - refining and electro - winning circuits, as well as in environmental treatment operations. This paper provides an update of commercial MRT applications in the copper industry. Several recent installations and test programs are reviewed including recovery of bismuth from tank house electrolyte, and from chloride matrix selenium reduction solution which is generated in the anode slimes treatment process. Recovery and refining of platinum group metals originating in the anode slimes is also discussed. Various other base metal and other target separations of interest to the copper producer are also reviewed. The recovery products are high purity metal salts which can be marketed directly or readily reduced to metal.

Jan 1, 2007

By T. Hartmann

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal industry. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowining (EW) cell can cause 'cathode burn'. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. First and foremost, they ensure a reliable, continuous extraction process and, second, they recover valuable re-usable organics from the crud.

Jan 1, 2007

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004