Search Documents

By E. S. Moore

"The Michipicoten-Goudreau area, bordering on the northeast corner of lake Suferior, has had a tectonic history related to that of the geosyncline occupied by this lake. This basin has been a major structural feature in the Canadian Shield since at least late-Precambrian time. It has been extensively faulted and was the centre of great igneous activity in the Keweenawan feriod . Many of the faults, folds, dykes, and sills in the surrounding regions tend to head directly or indirectly into this basin. Some of the faults in the Michipicoten-Goudreau area appear to run under the eastern part of lake Superior just as the large Keweenaw fault in Michigan extends into the lake on the south side. Some of these faults may even be extensions of or counterparts of the faults on the south side of the lake. Another set of faults in the Michipicoten-Goudreau area runs nearly transverse to some of these major faults, and it is evident that in some places movement has recurred at a later time on faults formed in an early period.STRATIGRAPHYThe rocks of this area, with the exception of Pleistocene and Recent formations, are all Precambrian:"

Jan 1, 1954

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By V. G. Minenko, A. L. Samusev

For efficient leaching of gold from sulfide ores and the oxidation of sulfides into sulfates, it is necessary to introduce a substantial amount of oxidant - atomic oxygen, hydrogen peroxide, ozone, potassium or sodium hypochlorite. In this paper, hypochlorite electrochemical treatment is proposed as an effective method of intensification of refractory ore leaching. The objective of the study is to increase the gold recovery from refractory ores with the application of chlorinated solutions that are modified by chemical or electrochemical treatment. The advantages of the use of the modified chlorinated solutions instead of cyanide for gold-sulfide leaching are considered to be the following: a high concentration of the oxidizing agent (hypochlorite ions) in solution helps to achieve a high speed of gold dissolution in the form of chloride complexes; the possibility to produce hydrochloric acid solutions that may be used for the recovering gold by electrolysis; the possibility of the processing of carbonaceous, arsenic-bearing and others kinds of refractory gold ores. The mechanism of the interaction of the modified chlorine solutions with gold-bearing sulfides (pyrite and arsenopyrite) was investigated. The efficiency of the application of chemical and electrochemical leaching method was proved. The main factor that limits the rate of gold dissolution is a high concentration of sulfate ions (SO4 2-) formed in the solution by the oxidation of sulfide minerals. The optimal parameters of chemical and electrochemical leaching method and effective ways to remove sulfate ions were determined. The method helps to increase the level of the gold recovery up to 87% from refractory ores. The intensification of leaching by chemical and electrochemical treatment opens up opportunities for the creation of modern efficient and environmentally-friendly technologies that may be applied for gold extraction from refractory gold ores.

Jan 1, 2016

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By P. C. Sui

Numerical investigation and parametric simulations of the coupled electrical conduction and mass diffusion in the GDL of a PEMFC are reported. The coupled transport is solved using a 2D, "under-the-rib" computational domain for the cathode GDL. The current density on the GDL/catalyst layer interface, which constitutes one of the boundary conditions for the GDL domain and reflects the activation overpotential in the catalyst layer and the ohmic loss in the membrane, is solved iteratively using a novel numerical algorithm. A parametric study is performed to investigate the effects on current density distribution of various operating conditions such as oxygen concentration and membrane resistance, and of design factors such as GDL geometry, anisotropic transport properties, and deformation under the land area. The results show that the current density distribution under the land area can be dominated by either electron transport or mass transport, depending on the operating regime.

Jan 1, 2005

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By D. Saramak, T. Gawenda, Z. Naziemiec, A. Saramak

"Crushing and grinding operations are burdensome to the environment due to generating large amounts of dust, noise and waste during course of comminution operations. An indirect negative contribution of industrial crushing processes is an increase of carbon dioxide emissions, which is a byproduct in energy production processes. On the other hand comminution processes in ore enrichment technology are essential due to liberation the useful minerals from the gangue, and producing the demanded particle size fractions of products. The article concerns investigation over negative influence of comminution devices on environment in terms of dust and noise emissions. Several various crushing devices were under investigations, both in laboratory and in industrial scale.The obtained results were analyzed in terms throughput and energy consumption achieved in various crushing devices. The test results allow to conclude that an intensity of dust generation for individual types of crushing devices is varied. An additional aim of this article is to link the aspect of mineral processing with its environmental impact and hence an influence of raw materials beneficiation industry on the quality of life of residents in immediate and close vicinity.INTRODUCTIONMineral raw materials beneficiation processes are an integral part of multi-stage processing of coal, iron ore and non-ferrous metals, production of aggregates, cement, or precious metals and stones. One of the common features of all beneficiation operations is their high energy consumption, which is mainly connected with various operations of feed particle size reduction. Comminution processes in ore enrichment technology are essential to expose and liberate the useful minerals from the gangue, while in aggregate production processes – to obtain the demanded particle size fractions of products. Crushing operations are characterized by a high degree of negative impact to the environment and humans, mainly due to:• High electricity consumption, which indirectly contributes to the increased emissions of carbon dioxide into the atmosphere, since CO2 is often one of the byproducts of energy production;• Relatively rapid wear of device working parts, what forces a production of spare parts and involvement of steel industry;• Intense dust pollution generated during crushing and grinding processes. This is one of the factors affecting the air quality and the consequent deterioration of the living conditions of inhabitants near mines and processing plants; and • Excessive noise emissions."

Jan 1, 2016

By P. E. Weidmark

"Energy, Mines and Resources Canada has published the first in a new series of reports that will examine selected mineral products that are imported.""Vanadium - An Imported Mineral Commodity"" looks at one of the 32 raw materials for which Canada currently is totally dependent on foreign sources of supply. Vanadium is used in Canada mainly as an alloying element in the manufacture of high-strength, low-alloy (HSLA) steels.The series will examine the supply systems for various selected imported non-fuel minerals, as an aid to developing policies that might lead to reduced dependence on external sources. Each report in the series will address a numberof questions:What countries do the mineral and its principal sub-products come from?How do they get to Canada?What are they used for?How vulnerable is the supply chain to disruption?Are there alternative sources?Are substitute materials available?In summary - how serious is Canada's supply problem for the mineral in question, and what should be done about it?Mineral Bulletin MR 188, ""Vanadium - An Imported Mineral Commodity"", is available for $3.00 ($3.60 outside Canada) from authorized government bookstore agents and many other bookstores, or by mail from the Canadian Government Publishing Centre, Hull, Quebec, KIA OS9."

Jan 1, 1981

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By A. MacKinnon, P. W. Kingston, W. F. Caley

"Wollastonite (CaSiO3]) is experiencing increased usage in a variety of applications, such as fillers in paints, plastics and resins, as an extender to replace both non-fibrous and fibrous materials (e.g. asbestos), and in the glass and ceramics industries. Significant new deposits of wollastonite have been discovered in Marmora Township, about 175 km northeast of Toronto. The geological setting of these large-tonnage. High grade deposits has recently been investigated to assess the possibility of their development. A preliminary study of the chemistry, as well as the mineralogy of six occurrences is presented. Based upon this information, it is suggested that several of the deposits have an excellent development potential.INTRODUCTIONWollastonite is an anhydrous calcium metasilicate (CaSiO3), with a theoretical composition of 48.3% CaO and 51.7% SiO2; the calcium may be partially replaced by iron, manganese, magnesium, and strontium. Commonly associated minerals include diopside, tremolite, idocrase, grossularite andradite, quartz, and calcite. Wollastonite forms as a contact metamorphic mineral within impure limestone near intrusive bodies of granite, or other acidic rocks, as the result of metasomatism of calcareous sedimentary rocks, or by the crystallization of certain magmas (e.g. carbonautes). Generally, the reaction of calcite with silica to produce wollastonite occurs when siliceous hydrothermal fluids from a granitic intrusion or primary silica in the limestone/marble react with calcite in limestone at temperatures between 450°C and 600°C."

Jan 1, 1989

By Y. Wong

The quality and quantity of secondary deposits, which include tailings streams and tailings dams, are increasing around the globe. The tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of CAPEX & OPEX. The most widely used process for the recovery of these valuable ultra-fine haematite iron particles is the Wet High Intensity Magnetic Separation technique, originally developed by Dr. Jones over 55 years ago. Many of the original machines are still working today. The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test works, design- and engineering works. Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a Tailings Storage Facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power- and water consumptions, capital requirements and projected operating expenses. The results show that the operating costs are significantly lower than the mining and processing operations which are required for an equivalent amount of iron ore. The recovery % of iron depends on various factors but is within the 30–50% range, at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process. The processing of secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the mine life and offer environmental benefits by reducing the tailings footprint and water usage.

Jan 1, 2016

"Technological innovation is an extremely complex activity. The author presents his interpretation of innovation and the innovative process. He reviews the strategy used by participants in coal mining innovation in the past and discusses changes required to meet the challenges of the future.Introduction if an industry is to be successful and viable in today's world, the companies active within the industry must remain close to the frontiers of knowledge. The coal mining industry is no exception. Technological problems facing the coal mining industry are basically economic and social. Economic problems are those concerned with the long-term growth and profitability and social problems, with the health and safety of the mine worker and the impact of the mining operation on the environment.Technological innovation can be a key factor in meeting these problems successfully. The general belief is that the information base for technological innovation exists within mining companies and governmental agencies but current industrial and governmental strategies and structures impede the transformation of this knowledge into the mining products and processes required for growth.The purpose of this paper is to determine where Canada is in terms of coal mining on the innovative ladder. The paper as presented: defines innovation and innovative process; gives an historical ""broad brush"" review o f innovation in the industry; and suggests the challenges to be faced in the future."

Jan 1, 1985

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By R. Gatzweiler

The Key Lake nickel-uranium deposits are situated within the Wollaston domain of the Churchill structural province. The host rocks of the two orebodies are of Aphebian and Helikian age. The orebodies occur mainly within a 5.2-km-Iong, northeast-trending zone which coincides with the intersection of the sub-Athabasca unconformity and a reverse fault striking east-northeast. The principal controls of mineralization are structural and lithostratigraphic (i.e., post-Athabasca faults, the sub-Athabasca unconformity and graphitic metapelites in the lower Aphebian, close to the Aphebian/Archean unconformity). Grades of up to 35% U3O8 and 20% Ni are recorded over intervals of up to 2 m. Some hypogene zonation exists and the nickel mineralization tends to underlie the high-grade uranium ore. The ore minerals include pitchblende, a-U307, coffinite, gersdorffite, millerite, niccolite, bravoite, zoisite, sericite, chlorite and kaolinite. The kaolinite is a post-ore, supergene alteration product. Chemical studies of the sub-Athabasca paleo weathering profile sho w that regolithization is characterized by depletion in Si02 and K20 and concomitant enrichment in Al203 and perhaps MgO. In the paleoweathering profile the ferromagnes ian minerals are chloritized, the Ksfeldspars sericitized and the plagioclase saussuritized. Preliminary geochronologic data from the ores reveal U/Pb ages of -1228 my, - 960 my and 89 my, and Rb /Sr data indicate basement ages of -1850 my and - 1372 my. Aphebian pelitic protoliths, carrying U and Ni, may have released some metals during post-Hudsonian weathering, and minor concentration in structural and geochemical traps may have taken place prior to the deposition of the Athabasca strata. However, it is felt that the bulk ofthe ore-grade mineralization wasgenerated after the deposition of the Athabasca formation and after faulting, probably during a major regional thermal/ intrusive episode of Grenvillian age. Several episodes of remobilization took place between 1228and 89 my ago.

Jan 1, 1979

By G. Pouskouleli, T. A. Wheat

"The role and benefits of using statistical methodology in the development and optimization of materials and processes is examined. It is shown that considerable benefits accrue from the use of an appropriate design in which a number of factors (process parameters) are varied simultaneously while the system response such as percent recovery, degree of separation, purity, etc. is monitored and ultimately optimized.Compared with the commonly encountered one-factor-at-a time approach, this schema exploits reduced experimentation (thereby requiring reduced resources [staff, time, dollars, etc.]) yet yields quantitative information on the significance of each factor and their combinations on the measured response."

Jan 1, 1992

By Y. P. Wu

Steeply dipping seam refers to the coal seam with dipping angle in the range of 35?55°, which is well recognized to be very hard to mine by the mining industry all the world. In the last two decades, some fundamental researches were focused on the strata behavior of long-wall panel, complicated rock mass breaking process of the steeply dipping seam, overburden stress field developing and evolution, rock strata breaking and moving process, rock structure stability mechanism and control. Results show that it?s presenting macro stress arch-shell (MSAS) of the stress distribution of the overlying rock in steeply dipping seam. The MSAS is the spatial distribution of intensity envelope line under the strength criterion and has the geometry shape asymmetry as well as the stress distribution heterogeneity. The arch- shell base will forward as the working face mine forward and the shell roof will extend to higher overlying strata above the gob. In this paper, the stress arch-shell analysis model and coordinate system were established and analyzed the inclined masonry structure at different zone. Analysis results show that the rock damage at the key part of the arch-shell is the main factor which causes whole overlying rock structure failure. The rock structure instability modes have tension instability of the shell roof, compression-shear instability of the shell shoulder and composite instability of the shell base, meantime, instability coefficient is proposed to determine instability condition. The above research results enrich the complex coal seams mining theory and provide a theoretical basis for mining safely and efficiently in steeply dipping seam.

Aug 1, 2013

By Robert B. Parsons

"While it might seem like heresy to suggest that ""taxation"" can be a source of financing, never the less some generous tax rules can considerably enhance the tax savings pertaining to a particular expenditure or project. A basic tax knowledge, and careful tax planning, can optimize government participation in a project. INTRODUCTIONIn trying to identify sources of financing for a project, ""government"" as a source of funding is normally thought of in terms of government grants, loan guarantees, interest rate buy downs, property tax waivers, hydro subsidies, and so on. Generally, such concessions are somewhat difficult to obtain, especially in the current period of apparent fiscal restraint. One source of government funding which should not be overlooked is the income tax regime, and, at the provincial level, the various provincial mining tax regimes.While the taxpayer would not normally view a tax system as a potential source of government financing, nevertheless various federal and provincial rules applicable to the mining industry can offer attractive tax deductions - and tax savings - with respect to particular expenditures. In fact, it is not unusual for a civil servant to refer to a tax deduction as a tax ""subsidy"". For example, in the right circumstances, the cost of a smelter expansion in New Brunswick would cost the operator only 31 cents on the dollar, with the federal and provincial governments paying for the other 69 cents by foregoing tax revenues (Table I). In a sense, such tax savings could be compared to a government grant equal to 69% of project costs. Of course, not every project expenditure will generate that degree of government funding. The fact of the matter is that the percentages of tax savings attached to different expenditures cover a wide range, depending on a complex mix of factors. The point to understand is that the tax rules can offer some valuable savings, even after tax reform, and that a basic knowledge of the tax rules can yield some fruitful rewards."

Jan 1, 1989

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By Tim J. Carew, Dennis C. Martin

"One approach to stabilization of rock slopes is to place a buttress at the toe of the slope to provide additional resisting forces and increase the length and strength properties along the failure surface. This paper describes the rock mechanics and mine planning aspects of incorporating a buttress of intact rock in the lower part of the slope as part of the slope design for the south wall of the final pit at Cassiar Mine. Stability analysis techniques and results are described. Analyses results have indicated that, in order to maintain steep over-all slopes in the final pit, a buttress of intact rock shoud be incorporated into the lower section of the slope until late in mine life. The effect of the buttress is to flatten the slope and reduce the slope height thereby improving slope stability. The mining plans would be such that the buttress would be mined out during the last four months of mining when the consequences of instability would be least severe.IntroductionThe concept of using a buttress to stabilize slopes has been used in mining and civil engineering construction in may locations (Richards and Stimpson, 1977). Most buttresses involve placement of coarse rock fill timber cribs or other material as a load at the toe of an already unstable slope to provide forces which resist failure by counteracting driving forces and increasing the length and strength of the failure path.This paper describes the geotechnical and mine planning aspects of incorporating a buttress of intact rock in the design of the south wall of Cassiar Mine. The effect of an intact rock buttress is to flatten the slope and reduce the slope height, thereby improving slope stability. No actual construction is required other than normal excavation of the slope. The ""mine plans would be such that the buttress would be mined out at the end of mine life when the impact of instability would be less severe and additional ore might possibly be recovered from the slopes. Mining of the buttress could induce instability at the very end of mine life at a time when maximum ore extraction has been achieved."

Jan 1, 1986