Search Documents

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By T. Macpherson

Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco's carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

By P. Espinoza, I. Yutronic, J. Olivares

"Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved.Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals.On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs.Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others."

Jan 1, 2012

By M. Mahdi Aboutalebi, Roderick I. L. Guthrie, Mihaiela Isac

"A preliminary computational fluid flow model has been developed to simulate the flow field of liquid steel in the mold region of billet mold casting. This study reports the effect of different Submerged Entry Nozzles (SEN) on the fluid flow in round and square billet, curved mold, casters. In this study, ANSYS Fluent 14.5 software was used to model the 3-D turbulent flow of liquid steel. The standard k-0 model was used to simulate turbulence in the mold region. Similarly, the species transport equations were discretized to simulate the dye injection test into the mold cavity. The behavior of flow in the mold region was validated against previous experimental work. Predicted results showed that different nozzle types plus the slight curvatures in the molds can significantly influence the flow patterns generated within the mold region, and thereby affect the finished quality of the billet products.INTRODUCTIONConventional Continuous Casting (C.C) processes are presently used to solidify more than 95% of the 1.5 billion tons of steel now produced in the world annually (World Steel in Figure, 2014). This overwhelming contribution of C.C processes for steel production is the prime motivation for this study, in order to understand and optimize the casting processes and thereby reduce internal defects and minimize energy consumption. The primary objective of all C.C processes is to maintain liquid metal purity during the casting process and to create a uniform flow within the caster so as to avoid internal and external defects. In this regard, studying fluid flows in the mold region of continuous caster has attracted many research groups, in both academia and industry, in recent years. The mold region is one of the most critical parts of the C.C. process, in which the transport phenomena associated with this region can significantly affect the quality of the final products. Thus, proper control of fluid flows within this region can be expected to greatly decrease both internal and surface defects such as Oscillation Marks (OM), inclusion entrapment, and Mold Powder Entrapment (MPE). In the casting process, the fluid flow in the mold region can be affected by a number of variables, such as; the flow control system (stopper rod or slide gate), nozzle geometry, SEN (Submerged Entry Nozzle) depth, casting speed, mold dimensions, gas injection, and the application of electromagnetic fields. One of the most influential and easily-changed fluid flows are the jets of steel issuing from the SEN. Nozzle geometries are variable, consisting of a number of exit ports, different port angles, and/or port sizes, the bottom shape of the nozzle, and the SEN immersion depth (Thomas, 2001). The SEN characteristics can markedly affect meniscus surface velocities, surface level profiles, and turbulence levels that can vary in terms of the frequency and the magnitude of their fluctuations."

Jan 1, 2016

By J. Peace, J. R. Fletcher

"British Steel has increased its usage of stainless steel for bunker, silo and chute linings to reduce maintenance costs and improve productivity.A generation of low cost 12% Cr steels has been specifically developed to satisfy the needs of hardness, flow promotion and through life costing which are demanded by bulk solids handling industries.The range of stainless steels include:• a very hard martensitic grade which is particularly suitable for high stress applications where impact and abrasion are predominant;• a titanium stabilized duplex steel for structural applications, as well as low friction , medium abrasion resistant wear liner plate; and• a ferritic stainless steel with rubber backing for low stress application where flow promotion of product is the predominant requirement.Industrial applications and experiences along with methods of fixin g the stainless steels will be discussed in conjunction with the relative through-life costs of the products.IntroductionBritish Steel has become one of the most efficient steel manufacturers in the world, with improvements seen in productivity, quality, delivery, performance and response to the needs of the worldwide market place.Part of this success stems from reductions in engineering downtime in the key areas of its operations, by the introduction of better engineering design and the use of enhanced materials where significant cost benefits have been identified.The nature of producing iron and steel requires the use and handling of a number of raw materials with wide ranging properties, each calling for a different approach to solving the difficulties encountered in storing and transporting these materials to their respective point of use. Figure 1 shows steel production for 1988-89 where over 30 million tonnes of raw materials were handled in making 14 million tonnes of liquid steel at British Steel's five integrated works.Typically solid raw materials include, iron ore, coal, limestone, ferro alloys and scrap. Intermediate products such as coke and sinter create their own specific handling and wear problems.Coals and ores are shipped into the United Kingdom from several sources, and have a great variety of properties. Some coals can be extremely wet and sticky, whereas others are dry and dusty . The ores handled can vary from wet concentrate and fines to heavy angular rubble and pellets. These raw materials are off-loaded, stored and conveyed through British Steel's own port facilities at Port Talbot, Immingham, Redcar and Hunterston. British Steel also produces the majority of its own coke and all its own sinter. Coke and sinter are frequently handled at elevated temperatures which cause other handling problems."

Jan 1, 1991

By L. Nastac, Y. Xuan

"The metal-matrix-nano-composite (MMNCs) in this research work consists of an A356 alloy matrix reinforced with 1.0 wt. % SiC 50 nm diameter nanoparticles that can be dispersed within the molten alloy matrix via ultrasonic stirring technology (UST) and induction melting and stirring processing. The necessary ultrasonic parameters to achieve the essential cavitation for adequate degassing and refining of the A356 alloy as well as the optimum fluid flow characteristics for uniform dispersion of the nanoparticles into the A356 alloy matrix have been investigated in this study by using computational fluid dynamics (CFD) modeling with a magneto-hydro-dynamics (MHD) model and an UST cavitation model.The MHD model accounts for turbulent fluid flow, heat transfer and solidification, electromagnetic field as well as the complex interactions between the solidifying alloy and nanoparticles by using ANSYS Maxwell and ANSYS Fluent Dense Discrete Phase Model (DDPM) and a particle engulfment and pushing (PEP) model.INTRODUCTIONAluminum matrix nanocomposites can offer outstanding properties, including low density, high specific strength, high specific stiffness, excellent wear resistance and controllable expansion coefficient, which make them attractive for numerous applications in aerospace, automobile, and military industries field (Bozic, 2010, De Cicco, 2009, Elshalakany, 2014, Goh, 2006, Jia, 2013 and 2015, Liu, 2014, Reihani, 2006, and Su, 2010).As shown in literatures (Aki, 1999 and Mussert, 2002), it is highly advantageous to use nano-sized ceramic particles to produce metal matrix nano-composites (MMNCs) since similar ductility and higher strength with the metal matrix can be achieved. Currently, there are several fabrication methods of MMNCs, including mechanical alloying with high energy milling (Chen, 1997) , ball milling (Filho, 2003), nano-sintering (Groza, 1999), spray deposition, electrical plating, sol-gel synthesis, laser deposition, etc. The mixing of nano-sized ceramic particles is normally lengthy, expensive, and energy consuming.Ultrasonic Stirring Technology (UST) has been extensively used in purifying, degassing, and refinement of metallic melt (Jian, 2005, Khalifa, 2008, Eskin, 2002, Xu, 2004, and Meek, 2006) mainly because introducing the ultrasonic energy into a liquid will induce nonlinear effects such as cavitation and acoustic streaming. SiC nanoparticles are widely used as reinforcement particles due to their relatively good thermal and chemical stability. Ultrasonic vibration can improve the wettability between the reinforced nanoparticles and the metal matrix (Lan, 2004, Cao, 2008, and Yan, 2011), which will assist to distribute the nanoparticles more uniformly into the metal matrix. Ultrasonic cavitation in liquids causes high speed liquid jets of up to 1000 km/h. Such jets press liquid at high pressure between the particles and separate them from each other (Hielscher, 2005)."

Jan 1, 2016

By J. Shibata, K. Manabe, A. Fuji, N. Matsunaga, D. Murakami, Yamaguchi University, T. Suzuki

"Spent hydrodesulphurization (HDS) catalyst contains rare metals such as cobalt, nickel (Ni), molybdenum (Mo), and vanadium (V). The overall objective of this project is to develop a hydrometallurgical process that provides a degree of high recovery and selectivity of these rare metals from spent HDS catalyst. As a part of this project, this study focused on (i) development of a solvent extraction-precipitation stripping process for separation of Mo and V from solutions and (ii) optimization of grinding conditions of alkaline leaching residue for selective Ni sulfuric acid leaching against aluminum (Al). Experimental results showed that effective separation between Mo and V can be achieved by the two-stage process; solvent extraction of Mo and V with TOA (tri-n-octylamine) and precipitation stripping of V with ammonium salt at pH above 8.0. Regarding grinding conditions of alkaline leaching residue for selective Ni leaching against Al, it was found that Ni leaching efficiencies increased by providing higher grinding intensity, while the Al leaching efficiency increased and then decreased with increasing grinding intensity.INTRODUCTIONHydrodesulphurisation (HDS) catalysts account for about one third of the total worldwide catalyst consumption and are extensively used for sulphur removal in petroleum refineries (Zeng & Cheng, 2009). Fresh HDS catalysts generally contain molybdenum (Mo) and nickel (Ni) on an alumina carrier, but various elements included in the crude oil such as sulphur, carbon, silica, arsenic, cobalt, and vanadium (V) deactivates HDS catalysts during HDS reactions. As a result, spent HDS catalysts contain high concentration of rare metals. For example, regarding to Mo and V, it has been reported in the literature that the concentrations of Mo and V in the general spend HDS catalysts are generally 10-30% and 1-12%, respectively (Zeng & Cheng, 2009), which makes it economically viable to recover these rare metals (Biswas et al., 1986).Among a number of processes proposed for the recycling of rare metals from spent HDS catalysts, alkaline leaching is often used for selective Mo and V leaching (Zeng & Cheng, 2009). However, the process which provides a high degree of separation between Mo and V from a leaching solution had not been developed. Therefore, the first objective of this study was set to develop a solvent extraction-precipitation stripping process for the separation of Mo and V from solutions. More specifically, using artificial aqueous solutions of Mo and V, a series of experiments was performed to optimize the extraction pH, stripping agent, and the stripping pH."

Jan 1, 2016

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By A. W. Jacobs

SHORTLY after Denny, Robson, and Irwin(l) published their first paper, in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery. It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter&apos;s source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in: (1) Shakers on machine columns, vibrated? by drills (2) Vials placed in drill holes to be blasted (3) Both homogeneous and heterogeneous. mixture with explosives ( 4) Packages with tamping (5) Compressed-air lines (6) Special compressed-air ejectors for use while drilling and after blasting (7) The discharge of ventilation fans (8) The filters of respirators It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium powder, and would interfere unduly with underground routine. Later, animal experiments by Denny, Robson, and Irwin(2) showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.

Jan 1, 1944

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units&apos; for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By M. M. Papic, G. M. Kimber

"Hat Creek coal was treated by the liquid solvent extraction process in a continuous plant at the U.K. National Coal Board Coal Research Establishment.Extraction levels of over 80 per cent dry-mineral-matter-free (dmmf) coal were achieved.Total light oil yield was around 47 per cent of the dmmf coal. The light oil was shown to be a good feedstock for secondary refining into gasoline, jet fuel and diesel fuel.In spite of the high mineral matter content of the coal the solid residue was successfully removed from the coal extract by filtration.IntroductionBritish Columbia Hydro (BCH) and the National Coal Board of Great Britain (NCB) undertook a joint project to test the Hat Creek coal from British Columbia in the NCB&apos;s coal liquefaction process designed to produce transport fuels and feedstocks for the chemical industry by the liquid solvent extraction of coal(1), In this process most of the coal is dissolved in an aromatic solvent and the residual solids consisting of mineral matter and undissolved coal are removed by filtration. The resultant coal extract solution is fed to a hydrocracker for conversion to light liquid products and a fraction suitable for recycling as solvent. The light liquid products can be converted to gasoline and diesel fuel in a secondary refining stage.The dissolution of the coal is effected by heat-treating a slurry at a temperature in the region of 400°C which causes some bonds in the coal to rupture with the formation of radicals(2,3). These radicals are stabilized by hydrogen transfer from the hydroaromatic groups in the solvent, resulting in a reduction in the molecular weight of the coal. In the absence of donor groups the radicals combine to form an insoluble high molecular weight product(4). From studies of the kinetics of these reactions it has been shown that the formation and stabilization of the radicals is rapid at temperatures around 400°C(2,3). The dissolution of the depolymerizing coal is, however, relatively slow and the need to ensure complete dissolution in order to achieve a high extraction restricts the selection of digestion time(5). Further, it is important that digests do not contain depolymerizing coal as it may re-form under the applied stress in the filter cake inhibiting flow through the bed and resulting in low filtration rates(6).Thus, in practice relatively long digestion times are generally required in order to ensure complete dissolution of the depolymerizing coal, while it is also important to avoid depletion of the hydrogen donor groups in the solvent which would lower the rate of hydrogen donation to the coal and thus reduce the extraction yield and adversely affect the filtration(7). Clearly it is desirable to optimize the digestion time and temperature with regard to the extraction yield and filtration properties.The precise control of the distribution of products from the hydro-cracker is important for the composition of the recycle process solvent. The principal functions of the solvent are to provide a source of donatable hydrogen and a vehicle for the dissolution of the depolymerizing coal. Hydrogen transfer from the solvent, achieved by the conversion of hydroaromatic to aromatic groups, stabilizes the radicals formed by thermal cleavage of some of the bonds in the coal resulting in a progressive reduction in the size of the coal molecules(8,9) and dissolution in the solvent. The combination of radicals would result in the formation of insoluble material and a reduced extraction yield of the coal(4). Thus to achieve a high extraction yield the solvent should contain sufficient hydrogen donor groups to prevent extensive radical combination. The composition of the solvent should also be controlled to allow dissolution of the depolymerizing coal and to prevent precipitation of this material during the subsequent processing of the coal digest and extract solution. The formation of a precipitate not only reduces the extraction yield of the coal and adve"

Jan 1, 1985

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e., fewer energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant. INTRODUCTION Solar energy can help make mining more sustainable (Moreno-Leiva et al., 2017). With falling battery costs, an autonomous solar supply is soon to become an economical alternative in many parts of the world, even in the presence of a larger power grid (Child et al., 2017). Although this, places with high solar radiation such as the Atacama Desert in Chile, nowadays show a large potential of incorporating solar energy as a supply of energy. Many of the Chilean copper mines are in this zone making it interesting to study their compatibility and potential of integrating this renewable source to their operation. The power demand in a copper mineral processing plant is determined by the main power loads in grinding and flotation, with grinding typically the largest power consumer, especially the semi-autogenous grinding (SAG) mills (Wei and Craig, 2009). In Chile, it corresponds on average the 50% of the electrical energy consumption (COCHILCO, 2013). Solar energy production is determined by the irradiance perceived into the solar photovoltaic (PV) panels (which varies through the geographic location) and several other climatic parameters such as the current season, humidity, temperature, altitude, and others (Molina et al., 2017). Also, solar energy is only generated during the sun hours, getting to a maximum generation at a certain peak hour during midday, and finally dropping to zero during the night. This shows a cyclic parabolic profile as shown in Figure 1. Due to the SAG mill operated continuously, the power supply always must be available. During the night, to continue supplying the energy, it is necessary to complement the solar power generation with a battery energy storage system (BESS), which will act as a power backup and a buffer. For the optimal sizing of this PV- BESS system, information of the demand profile is needed (Pamparana et al., 2017). In the case of the SAG mill operation, the resulting demand relates to the ore-hardness for a specific throughput and grind size (Morrell, 2004). Therefore, for a given throughput and target grind size, a harder ore would require more power, and variable hardness results in more variable demand and a subsequent need for larger energy storage (Bueno et al., 2015). Due to the ore-hardness variability and the operation of the mill, the power demand profile in inherently variable.

Jan 1, 2019

By W. G. McBride

The mining industry has already become highly technical in all its branches and this has brought about specialization in mining engineering. Increasing demand for mineral products, exhaustion of high-grade or easily worked deposits, and narrowing of the fields for exploration and development, are forcing mines to greater depth and to working material of lower grade and more complex composition. The Robinson Deep at its Turf shaft has reached a depth of 7,640 feet and expects to go to 8,500 feet; Miami Copper, under normal market conditions, profitably mines ore running only 16 pounds of copper to the ton; Alaska Juneau is making a profit on ore running about $1.15 per ton in gold; and many mines are handling ores of an extremely complex nature. In each case, the success of these operations has depended upon the application of sound scientific principles and good business methods to the problems involved. It may be safely assumed that mining at great depth and the exploitation of low-grade, or complex, ores will become more and more important as time goes on, and this means that greater and greater demands will be made upon the technical skill and business ability of the mining engineer. To meet this condition, the more or less haphazard methods of training the young engineer that have prevailed in the past will have to be replaced by a careful and well-ordered system of engineer-training. Upon the industry and the older mining engineer falls the duty of providing means to assist the deserving student to prepare himself properly to meet the increased demands that are falling upon his profession. Consideration of the training of the mining engineer involves a decision as to what constitutes his field of usefulness. Technical control of methods and processes obviously falls upon the engineer, but there are still many who doubt his usefulness in the executive field, particularly in positions involving close contact with the men and work. Many engineers have failed as shift-boss or foreman, but this has been generally due to fault in the management in using men who were temperamentally unfit to lead others or who lacked the necessary preliminary training.

Jan 1, 1932

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986