Search Documents

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick's gold price hedging program.IntroductionThe company's balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders' equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company's conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick's hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

By G. S. Cole

By 2025, the U.S. automotive industry will have to average 54.5 mpg (4.3l/100km) Corporate Average Fuel Economy (CAFÉ). While new/improved powertrain technology (turbocharging, electrification, diesels, transmissions and stop/start) will be critical, it is estimated that 25-40% of the new CAFÉ standards will require significant mass reduction, and lightweight structural materials will be required. This presentation examines vehicle mass reduction based on new developments in manufacturing automotive structures and components using light metals (aluminum and magnesium), conventional heavy metals (iron and steel), polymers, and carbon-fiber reinforced polymer composites. Components that used to be sand cast or pressure die cast provided minimal fatigue strength and ductility. But greater mass reduction uses more light metals in structural applications. They require eliminating porosity and inclusions to improve ductility and fatigue strength. Improved casting processing, with vacuum die casting, counter pressure and squeeze casting, and new forging and extrusion applications are being developed for this purpose. New grades of ultra-high strength steels can be made thinner, and save over 1/3 the mass vs conventional mild steels. But more complex and expensive processing, such as hot stamping and in-mold quenching, is required. Most engine block structures have migrated from grey cast iron to aluminum over the past 40 years. But compacted graphite cast iron has higher strength at high combustion temperatures and pressures so that high powered engines can be smaller and even lighter than aluminum. Assembling a range of lightweight materials into vehicle structures requires specialized assembly techniques, including sophisticated structural adhesives that can mitigate vehicles’ unique corrosion environment. The presentation will conclude with discussing lightweighting strategies of Asian, American and, European marques and the materials, component designs and assembly techniques used to achieve 2025 CAFÉ.

Jan 1, 2016

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By S. Esmaeili

The yield strength model developed by Esmaeili, Lloyd and Poole [1] has been adapted to model isothermal aging in Cu-containing AA6xxx alloys, with (a) a moderate and (b) a very low Cu content in the solution-treated, as-quenched, condition, Isothermal calorimetry has been used to analyze the kinetics of precipitation in these alloys, While the kinetic parameters for the low Cu alloy has been derived from the present experiments, the previously determined kinetic parameters for the high Cu alloy AA6111 has been used to model the precipitation kinetics in the moderate Cu alloy. The age hardening responses of both alloys have been well predicted by the model.

Jan 1, 2005

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By R. D. Studer

"The Snow Lake massive sulphide deposits are hosted by Aphebian volcanic rocks of the Flin Flon - Snow Lake greenstone belt, which in this area were deformed and metamorphosed to the amphibolite facies during the Hudsonian orogeny. All the known deposits occur in felsic rocks a short distance below the contact with an overlying mafic rock unit.The Stall Lake copper deposit occurs close to the top of an explosive felsic volcanic sequence. Rocks stratigraphically underlying the deposit have been hydrothermally altered by the mineralizing fluids. The sulphides were probably deposited from submarine volcanic vent(s) on the flanks of a felsic dome. The ore has been tightly folded, flattened and elongated parallel to the northerly trending lineation of the surrounding rocks during the several periods of deformation. Strike lengths of the lenses range from 60 to 300 feet and plunge-to-strike ratios are as much as 15:1.Ore lenses I to 4 typically consist of massive coarse-grained pyrrhotite, chalcopyrite and pyrite. A stratigraphically higher lens differs in that it contains fine-grained pyrite and chalcopyrite, with an increase in sphalerite toward its hanging wall. The No.4 orebody has a distinct footwall alteration zone characterized by brecciation and abundant chlorite-staurolite- garnet schist, with minor kyanite, anthophyllite, cordierite and anhydrite, as well as sulphide minerals. Chemically, the alteration zone is distinguished from the unaltered felsic rocks by Na20 depletion and Mg-Fe enrichment"

Jan 1, 1982

By Gerhard Kircbner, Boen Tan

"IntroductionThe Key Lake uranium-nickel ore deposits are located in the Athabasca Basin of northern Saskatchewan, Canada (Fig. 1). Many papers have been published on Key Lake in the past (Dahlkarnp and Tan, 1977; Kirchner and Tan, 1977; Kirchner et al., 1980). Immediately after its incorporation in 1968, Uranerzbergbau GmbH, a German holding company, set up exploration subsidiaries in Australia, the United States and Canada. This account reviews those exciting years starting with the concept to explore the rim of the Athabasca Basin in Saskatchewan, and leading up to the discovery of the deposits in 1975 and 1976.A few summary statements can be made:• The discovery of Key Lake resulted from a very systematic exploration approach and the persistence of Uranerz, the operator. • Cluff Lake and Rabbit Lake had been discovered some seven years before, but it was the discovery of the Key Lake deposits which brought Saskatchewan to the forefront to become Canada's foremost uranium producing province.• The experiences gained at Key Lake, which were subsequently published, triggered the discovery of many other deposits of similar, or even larger, size than Key Lake. The spatial relationship of those deposits to graphitic conductors and hydrothermal alteration zones are presently the most effective indicators for locating new deposits - indicators which were first recognized at Key Lake.• Key Lake is, and will remain for some years to come, the largest producing high-grade uranium mine in the world."

Jan 1, 1994

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By F. Habashi

"Extractive metallurgy was divided into the three sectors pyro-, hydro-, and electrometallurgy in 1959 when Professor Joseph Newton at the Idaho School of Mines in Moscow mentioned this in his book Extractive Metallurgy. Pioneer hydrometallurgists who built this discipline can be traced to the alchemists in the ninth century. It is now a mature subject of great importance in which pressure plays a vital role. Short biographies of some hydrometallurgists and the processes they invented are briefly outlined.INTRODUCTIONHydrometallurgy is the use of aqueous solutions to recover metals from ores. It is a relatively new discipline when compared with pyrometallurgy the use of fire to melt ores and recover metals which was practiced in ancient times. Hydrometallurgy can be traced to the time of alchemists whose concern was the transmutation of base metals into gold. Although alchemists did not succeed in their venture yet they described many reagents that are useful today. For example, they prepared sulfuric acid by distillation of iron vitriol, muriatic acid by distillation of sulfuric acid with salt, and nitric acid by reaction of sulfuric acid by reaction of sulfuric acid with salpeter. Jabir Ibn Hayyan the Muslim alchemist who lived in the ninth century (Figure 1) described aqua regia a mixture of nitric and hydrochloric acid that can dissolve gold although either acid has no action on gold. THE MIDDLE AGESIn the Middle Ages, it was reported that copper was recovered at Rio Tinto in Spain by allowing copper-containing pyrite to be exposed in piles to the action of air and rain. Copper sulfate solution obtained was treated with pieces of iron to precipitate metallic copper—a process that was called cementation. Georgius Agricola (1494–1555) (Figure 2) a medical doctor in Saxony who used to visit mines and smelters to examine miners and metal workers, described in his book De Re Metallica the parting of gold, i.e., separating of silver from gold by acids."

Jan 1, 2016

By H. S. Bostock

"The study of the geology of Mayo district began in 1900 with R. G. McConnell's exploration of Stewart river; and has been carried on intermittently for the Geological Survey of Canada by J. Keele; D. D. Cairnes; W. E. Cockfield; C. H. Stockwell; and the writer. It has revealed a thick group of schists; quartzites; and crystalline limestones; almost certainly Precambrian in age; placed in the Yukon group; and a group of younger intrusive igneous rocks varying in composition from granite to gabbro. These include bodies of many sizes and forms; from stocks 8 miles across to small dykes and sills.Prospecting in the district began about 1897 and has disclosed the presence of gold, silver, lead, tungsten, tin, zinc, antimony, copper, arsenic, manganese, and mercury, both in placer and lode deposits . Of these metals gold, silver, and tungsten have been produced from placer deposits, and silver, lead, and gold from lodes. This paper deals only with some structural relationships of the lode deposits, generally referred to as the silver-lead veins, which have yielded the greater part of the mineral production of the area. From 1938 to 1941 the geological mapping of the district for publication on a scale of 4 miles to 1 inch was carried out by the writer, and the ideas expressed here are based on this work. No comprehensive detailed study of the silver-lead veins has been made, but the mapping has brought to light several important facts. The rocks of the Yukon group, although of a striking sameness throughout their section, can be divided into a number of distinguishable members by means of which the main structures can be traced . The most important and readily distinguishable rock in the group is referred to here as the quartzite member. This is composed of quartzite and schist in about equal proportions. The quartzite is resistant to erosion and forms most of the outcrops of the'member and the peaks of the Gustavus mountains and mount Haldane (Lookout)."

Jan 1, 1954

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"This paper briefly summaries the status of a recent program aimed at identifying new chemistry for use as sulfide mineral frothers and collectors. The background motivation and planning behind this work is given along with the general families of chemical structures synthesied and studied in detail followed by typical flotation application results in various laboratory and plant scale tests. Flotation testing to date has been very encouraging with often improved recoveries of certain minerals and improved pyrite selectivity being observed over commercially available reagents. In addition, in some cases, the dosage and lime requirements of these new collectors are significantly less than that associated with standard sulfide mineral collectors. INTRODUCTIONFroth flotation is one of the most widely used and economic means of concentrating metal sulfide ores. There are numerous reference books that have been published on the chemical aspects of flotation [e.g., ref. 1-7] which are based on studying the influence on selected minerals of chemical structures that have been used commercially for many years. In fact, almost 98% of the volume of flotation collector and frother reagents used at the industrial level today were known and manufactured in some form 25 years ago [8]. There are many reasons for this lack of significant new flotation reagent development [9] including the general utility and relative cheapness of existing collectors such as xanthates and existing frothers such as the alcohols and glycol ethers. Another reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials. This environment makes reliable reagent comparisons difficult and seriously limits the use of theoretically based chemical structure studies to predict new or optimal reagents. In addition, the higher cost of specialty flotation reagents demands that their performance attributes be significantly greater than that achieved with existing all-purpose commercial reagents - something often difficult to prove in practice."

Jan 1, 1988