Search Documents

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By T. I. Kunkel

The economic prosperity of many Canadian communities depends on resource extraction within the traditional territories of Indigenous people. The geographic sites where these resources are situated are also areas where these Indigenous people have sustained themselves for millennia through hunting, fishing, trapping, and gathering activities. These traditional activities provide not only sustenance, but also cultural and spiritual values, and the ability to transmit oral Indigenous cultures and customs from generation to generation. The multimillion dollar revenue mine project proposed within the Cariboo Chilcotin region of British Columbia is situated geographically in a location which has sustained the Tsilhqot?in people for millennia. However, this group of people have important social and cultural values nested within the traditional activities at this location. These values are typically not at the forefront of resource development. Using Indigenous research and grounded theory, this research paper briefly outlines Aboriginal values of the First Nations communities within the Cariboo Chilcotin region and some lessons learned from the Tsilhqot?in people during the environmental assessment of the mine proposal.

Aug 1, 2013

By D. R. Winchester

"I wish to thank you and your organizers for inviting me to address you at this point in time when we are all concerned for the future of the mineral industry in Canada.My topic ""Some Initiatives of Government Assistance to Industry Applicable to Mineral Processing"" is purposely limited in scope. To cover the entire range of initiatives in detail would take me all day, and at best, would be a mere recital of program titles, and a one sentence summary of the contents of the program. As you know, OREE or Regional Economic Expansion, is in the process of being amalgamated with elements of the Department of Industry, Trade and Commerce. We will become Regional Industrial Expansion or ORIE. If the name Canada Dry becomes popular, I don't think we will object as we hope to become a good mixer. The entire departmental thrust has been re-evaluated, and is in the process of being re-constituted to better serve the nation, and industry as a whole. Amalgamation of the industrial, trade promotion and marketing support skills of IT&C, with the regional development orientation and decentralization program delivery mechanisms of DREE, will, it is believed, provide better support to industry on a national and regional basis."

Jan 1, 1983

By A. Fawceit, B. C. Dyer

"The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.IntroductionThe technique of seismic tomography has been most widely applied in oil industry exploration, nuclear waste disposal, civil engineering site investigations and in the assessment of the condition of mass concrete structures. Although model studies had indicated that tomography would be a useful tool in mineral exploration, relatively few applications have been reported.Essentially the method relies on the determination of the speed with which sound travels through a region within a cross-section of the earth or large body. The speed of sound is determined by the physical characteristics of the medium through which it is passing. In geophysics the speed of sound is generally referred to as the seismic velocity. Due to variations in the formations of different rocks the seismic velocity will vary and so can be used to map geological boundaries"

Jan 1, 1994

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By Benoit Taillon

Contenu de la presentation 1. Le projet QMM et son contexte 2. Gérer la biodiversité 3. Résultats obtenus QMM QIT Madagascar Minerals S.A. ? JV: Rio Tinto (80%) et Madagascar (20%) ? Trois gisements: Mandena (en cours d?exploitation), Ste-Luce et Petriky (total 6000 ha) ? CapEx : USD 940M (Installations minières + port, énergie, routes, logement, écoles, cliniques, etc.) ? Technique par dragage des sables minéralisés et de concentration de l?ilménite (FeTi02) ? Exportation de l?ilménite pour son traitement.

May 1, 2011

By B. S. W. Buffam

Introduction The development of uranium deposits is a relatively recent phase of mining in Canada. To date, the only producer of uranium ores on a commercial scale has been the Port Radium mine on Great Bear lake, N.W.T. However, with.-in the past few years intensive prospecting has been carried on throughout Canada and many occurrences of uranium-bearing minerals have been discovered. Eldorado has been active in the search for and the exploration of uranium deposits in Canada for a longer period than any other company and has, therefore, accumulated a considerable fund of information, especially about occurrences in Saskatchewan and in the Northwest Territories along the western fringe of the Precambrian Shield. The Company has also had experience in the underground operation, and in the mining, of uranium ores at Port Radium. During the past year or so many requests have been received from the prospecting and mining fraternity for information and guidance regarding the development of the many new uranium discoveries that have been made in Canada. Assistance by Eldorado is freely given whenever possible and this paper is presented to supplement the private discussions and to provide as wide a distribution as possible of the data acquired by Eldorado.

Jan 1, 1951

By I. Bakry

Uncertainty is an inherent characteristic of construction projects. Neglecting uncertainties associated with different input parameters in the planning stage could well lead to misleading and/or unachievable project schedules. The objective of this paper is to present a new approach towards scheduling repetitive construction projects while accounting for uncertainty. The paper presents an algorithm that quantifies anticipated delays resulting from different sources of uncertainty in the form of fuzzy time buffers. Through inserting the time buffers in strategic places in a time schedule, the algorithm provides protection against those main anticipated delays. The presented algorithm comprises two integrated components, a scheduling component responsible for producing a basic Linear Scheduling Method (LSM) schedule with deterministic activity durations, and a buffer component that handles fuzzy buffers sizing and insertion. The presented algorithm offers four different buffer insertion techniques covering different cases of interrelations between successive activities. The algorithm is implemented in a spreadsheet application, which automates calculations, yet allows users to fine tune the algorithm to fit the project at hand. With a focuses on highway construction projects as an example of repetitive construction projects, this paper accounts for sources of uncertainty such as weather, site conditions, change orders and equipment related delays. A hypothetical case is studied and explained to further demonstrate how the proposed algorithm works.

Aug 1, 2013

By Matthew Russell, Bobby Randhawa, Leopoldo Mariscal Samaniego, Jose A. Puente, D. Brosig, Paykan Safe

The La Caridad copper smelter, located in Nacozari, Mexico, have started a multi-year plan to reduce sulfur dioxide and particulate matter emissions into the environment. In 2014 the smelter completed a voluntary plant-wide SO2 process emissions inventory as part of the smelter’s proactive environmental stewardship policy. In turn, this triggered the development of several environmental projects to alleviate these emissions. A strategy consisting of improved capture efficiency of the sources with greatest impact has been followed to maximize cost-effectiveness. The reduction of secondary emissions from the Teniente Converter, as well as of primary and secondary emissions from the Peirce-Smith Converters have been key areas of priority. Additionally, a new system to capture and recover particulate matter from the Anode Refining Furnaces off-gas is also in the process of being implemented. This paper presents an overview of the work developed behind this effort and the smelter’s vision towards a greener future. INTRODUCTION The La Caridad copper smelter is owned and operated by Metalurgica de Cobre S.A. de C.V. (a subsidiary of Grupo Mexico). Currently, the smelter has a production capacity of 300,000 tonnes of anodic copper per year. The smelter is coupled with a 300,000 t/y electrolytic refinery. Other by-products (such as precious metals and sulfuric acid) are also generated as part of an integrated process. The original smelter started operating in 1986 with one Furukawa concentrate dryer, one Outokumpu Flash Smelting Furnace (FSF), two slag cleaning electric furnaces (SCFs), three Peirce-Smith Converters (PSCs), two Anode Refining Furnaces (ARFs) and one casting wheel. In 1997, a plant expansion project was concluded with the installation of one steam dryer, one Modified Teniente Converter (MTC), one additional ARF, one additional casting wheel, and the electrolytic refinery [1]. Over the years, the smelter management has implemented numerous environmental projects to alleviate SO2 and particulate matter (PM) emissions. The smelter process gas handling system captures the process gases from the FSF, MTC, and the three PSCs. The process gases are cleaned and conditioned and sent to the two acid plants. The first acid plant (with a capacity of 226,000 Nm3/h, wet basis) was commissioned in 1988 to process the FSF and PSC off-gases. A second acid plant (with a capacity of 195,000 Nm3/h, wet basis) was commissioned as part of the smelter expansion project [1]. The PSCs also have a secondary gas handling system with a dedicated baghouse and stack. The Furukawa dryer off-gas reports to a dedicated electrostatic precipitator (ESP) for dedusting before venting via a local stack. Process gas from the two SCFs, along with hygiene ventilation from various sources inside the smelter (including matte and slag tapping hoods from the FSF) report to a baghouse-based gas handling system and vent to atmosphere via a local stack. The original ARFs do not have an off-gas handling system, however, each ARF has a post- combustion chamber which naturally vents the process gases to the atmosphere via a dedicated stack.

Jan 1, 2019

TIPS FOR SUCCESSFUL WASTE MANAGEMENT ? WASTE MANAGEMENT PLANS ? Define the question to be asked in waste characterization studies ? Calibrate assessments and designs with field conditions ? Ensure consistent with short, medium and long-term mine plans ? Design robust plans - goalposts and expectations will change ? Fully assess and integrate costs into economic models ? Integrate waste specialists into the feasibility and design teams ? Keep it simple and when you can?t, communicate it in simple terms ? PLAN EXECUTION ? Integrate the waste management plan into daily mine operations ? Identify the critical KPI?s , track them and set clear action triggers ? Know the difference between knowledge and data ?make sure you retain knowledge and document the important Maintain management, engineering and operational focus through the mine life

May 1, 2010

By T. R. Skerry, H. P. Hudson, T. E. Warren

"ALTHOUGH coal is generally the cheapest fuel on the basis of heating value it has been at a disadvantage in competition with other fuels because means have not been available for efficient •Conversion of its thermal energy to mechanical work. Taking the •railway application •as an example, the cost of Diesel oil is about three times that of its thermal equivalent in coal, but the overall efficiency of a Diesel locomotive is about five times that of a coal-fired steam locomotive. Accordingly, the Canadian railways are replacing all coal-fired steam Locomotives, as they are retired from service, with Diesel units. This conversion in itself represents a major loss to the coal industry because the value of railway fuel is approximately 130 million dollars per year, and there are other applications in the medium power range where oil is displacing coal. There is, therefore, a strong incentive to attempt development of an efficient coal-burning engine.Coal has never been a promising fuel for reciprocating internal combustion engines because of the time required for its combustion in pulverized form . This is not less than one-tenth of a second so that the speed of such an engine would have to be very slow. There are also serious difficulties of a mechanical nature arising from the necessity for intermittent combustion and the use of close-fitting pistons."

Jan 1, 1952

By O. Moselhi

The purpose of this research is to evaluate the impact of Building Information Modeling (BIM) on Just-In-Time (JIT) material delivery, with a focus on how the use of BIM can help improve efficient implementation of JIT and reduce the cost of material management. Previous research and a number of case studies have addressed the positive impact of BIM on construction at large but none focused on JIT in construction. This paper presents a methodology for selecting reliable material vendors. It also utilises the integration of BIM and scheduling software to generate quantities of material and its required delivery time to improve the flow process and improve its reliability to minimise related delays and productivity losses arising from idle and non-productive time of equipment and labour on jobsites. 4D visualization is utilized to support coordination and timing of JIT material deliveries in an effort to minimize congestion on job sites. Case studies on JIT material deliveries are presented and the impact of BIM implementation on reducing the cost of material management is evaluated. The joint effect of BIM and JIT on quality control, elimination of waste, reduction of inventory buffers, and on relationships with material vendors are evaluated by analysing and comparing data from case studies. The paper also presents a methodology based on multi-attribute decision criteria for modelling the selection criteria for material vendors. The model can assist in ranking vendors not only based on cost and quality but also on their reliability in delivering material on time.

Aug 1, 2013

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By T. Shellhammer, A. Park

Among all pure metals, copper has the second highest thermal and electrical conductivity, next to silver. These properties coupled with a reasonable cost, make copper ideal for use in metallurgical vessels as a conductor of electrical current, as well as a lining material and protector of refractories and steel superstructures. Treatments of copper to address it’s softness and low melting point, specifically hard surfacing and calorizing, will be discussed. This paper will cover the evolution of copper to its current form, offer comparisons to other materials, and theoretical and empirical evidence on its superior performance in metallurgical vessels such as blast furnaces, basic oxygen converters and electric arc furnaces. Some case studies will be provided and finally a brief summary.

Jan 1, 2015