Search Documents

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By Charles Camsell

THE Northwest Territories covers a very large area-more than one-third of all Canada-and its most northern point, Cape Columbia in Ellesmere island, is distant only 500 miles from the Pole. Our first knowledge of the Arctic Archipelago, of which Ellesmere island forms a part, resulted from a gold-mining venture in Queen Elizabeth&apos;s reign. The English navigators of that time were eager to find a north-westerly and shorter and Jess hazardous route to the riches of China and Japan than that which Magellan had discovered, but they were unaware that the continent then known to bar a direct route extended in great width far to the north. Frobisher was one of these navigators. He reached in 1576 the bay in Baffin island now named after him, convinced that he had found a passage connecting the Atlantic with Asiatic seas. Forced to re-turn after ordeals in which ice, wind, and Eskimos flayed formidable parts, he brought back, among other novelties, a piece o black stone which had been picked up casually by one of his officers, and gave a little of it to the wife of one of the venturers, or financial backers of the enterprise. To quote now from Hakluyt: ? &apos;She by chance threw and burned it in the fire so long that , at length being taken forth and quenched in a little vinegar, it glistered with a bright marquesset of gold. Whereupon the matter being called in sorne question, it was brought to certain goldminers in London to make assay thereof, who indeed found it to hold gold and that very richly for the quantity." On the strength of this, the venturers, anticipating much profit, launched a second expedition to secure more of this stone, and 143 persons, including 14 miners and finers, set forth in 1577 and returned the same year, with, however, 200 tons of another mineral. Influenced by glowing accounts of veritable mountains of this mineral and by assays made after "additaments"-that is how "salting" in those days was described-the venturers, including Elizabeth, supplied funds for erecting a smelter and refinery at Dartford and outfitting a stilllarger expedition. And so, in 1578, fifteen ships departed with the Queen&apos;s blessing, for the same remote shores. After many mishaps, they returned with over 1,000 tons of the mineral, but when it yielded very little of value at the works in Dartford, the? Company of Venturers was forced into liquidation. Though our first prospector and miner was rather inconsiderate of the investors, he proved the existence of an archipelago, hitherto unknown, and secured much information about the new land and its dwellers.

Jan 1, 1938

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By M. N. Pons, F. Ferrari, V. Houzelot, B. Laubie, A. Bani, Université de Lorraine-CNRS LRGP

"More than 400 plants in the world are able to accumulate nickel in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, nickel (Ni) can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and recovering metal and has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Plants can be grown on serpentine soils, containing rather high concentrations of Ni, on sterile heaps or on contaminated soils. This crop enables us to extract Ni from secondary resources, and to improve soil quality by lowering its metal content. For example, Alyssum murale can be grown at the field scale in the Balkans, at yields corresponding to 110 kg Ni per hectare.Hydrometallurgical processes have been designed from the lab scale to the pilot scale to produce nickel salts: ANSH (ammonium and nickel sulphate hexahydrate), nickel sulphate, acetate, etc. and so on. These salts are used for surface treatment and in the paint and chemical industry. Ni salts are prepared from ashes, after plant calcination. Processes are based on the conventional methods of hydrometallurgy: acid leaching followed by different precipitation steps. These processes will be presented, as well as the pilot scale design. A life cycle assessment has been performed and clearly shows the environmental interest of this approach as a potential part of an anti-erosion strategy. An economic assessment has proved process feasibility and the final step is the launching of a start-up. At the moment, the approach is widened to other metals (cadmium, cobalt) and rare earth elements (REEs)."

Jan 1, 2016

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By Sang-Kyun Woo

The electric power conduit (EPC) in Korea has been constructed since 1978. Facing the challenge of safety and sustainability of the EPC, it is urgent to develop an inspection strategy and maintenance system for the structure based on the concept of life-cycle management. This paper introduces the newly developed mobile inspection and diagnostic system of the EPC. The novel aspect of this particular system is the integration of non-destructive mobile inspection techniques with BIM (Building Information Modeling) and LBS (Location-Based Service). BIM is an ideal tool and platform for developing an inspection and diagnostic system, and RFID (Radio Frequency Identification) is a useful tool to construct USN (Ubiquitous Sensor Network) for LBS. The goal of this research is to establish an EPC inspection and diagnostic system concept based on BIM and LBS using RFID. In this research, a BIM model of OPENTBM tunnel for EPC will be established to show the integration of 3D CAD with the inspection data. An EPC?s maintenance database, which includes the deterioration types of the structure, inspection records, and repair methods, was designed to interact with the BIM. The system will be implemented by the BIM with the related database, in which the construction geometry and all related information are stored. The proposed system was designed to utilize the inspection and diagnostic system under the USN environment using RFID in EPC directly.

Aug 1, 2013

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By R. Heikkilä

As a part of a large research and development program in Finland, a system calibration for an UAV measurement method having practical experiments in a Jorvas Railway Yard design and construction project. The Railway yard construction are was measured using an UAV measurement device by Smartplanes (Smartone) and using some reference points measured by a GNSS device. The measured data was cleaned, combined and adjusted through Least Squares Optimization using the software developed by a Finnish company Pieneering Oy. As references, two different laser scans as well as total station surveys were used. For applicability evaluation, the accuracy of measurement, the reliability of measurement, and the economy of measurement were used. Based on the comparisons, the achieved precision of the UAV measurement was high, instead the accuracy of measurement was not sufficient in this case. The principle of this photogrammetric measurement includes a lot of redundant observations making it possible to achieve a high level of reliability. The economy in this Railway Yard Design project was not able to achieve.

Aug 1, 2013

By M. Vaccarini

In this paper a possible methodology to supplement a predictive control approach is reported. The benefits deriving from the application of a predictive control on complex buildings lay on its capability of adapting in advance to the conditioning needs of indoor environments. In fact, the mere reactive control is usually affected by response delays, mainly determined by latency intrinsic in systems and by the massive nature of buildings, which slows down their response to changeable inputs. Hence, systems are too often solicited at their maximum power to recover against comfort deficiencies, and high consumptions are had. This paper reports on the application of a predictive approach to the Passeig de Gracia (PdG) metro station in Barcelona, which is a considerably high energy demanding building and where ventilation systems are used to control both comfort and air quality. Although an extensive simulation for estimating energy savings obtainable through that approach is currently ongoing, in this paper we detail the several components which make up a ?predictive control framework? and we perform a preliminary demonstrative simulation. In particular, the whole setup is formed by: a detailed model of PdG, which simulates the station?s ?real state?; a control model, which optimizes a given cost-function; probabilistic predictive models to infer the future state of the systems, given the assumptions on the control actions by the control module. The outcomes of this paper show that the procedure is applicable and preliminary results over a short simulation horizon of half a day are reported.

Aug 1, 2013

By David C. Cook

The milling complex, situated just east of the Cassiar townsite, receives raw ore from the tramline and processes it into 105,000 tons per year of milled asbestos fibre. The ore is passed through a concentrator, where a barren rock fraction is removed. The concentrated ore, representing 70% of the feed, is dried, stored and then milled into nine separate fibre classifications. The finished product is packaged into 100-lb bags and loaded into trucks in one-ton units. New air-handling facilities were added in 1977to provide additional air for environmental control.

Jan 1, 1978

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968