Search Documents

By Amir Karami, Derek Kinakin, Catherine Schmid

The Mathews Stability Graph Method (Mathews et al., 1981) has been used by geotechnical engineers and mining engineers for over 40 years to estimate the performance of longhole open stopes in underground mines. The method is widely used and accepted by practitioners because it is relatively simple to use and can be modified to account for observed performance at a given mining operation. While the simplicity of the method increases its accessibility and utilization, it does not intrinsically account for variability in the various inputs, including rockmass quality, structure, stress, or stope orientation. This paper presents a modified approach for the Stability Graph Method, whereby Python scripts are used to process available geotechnical datasets and combine them with actual or potential distributions of Q parameters, induced stress, structure, or stope orientation. The resulting Stability Numbers are then plotted as a contoured distribution on the Stability Graph.  This allows the practitioner to quickly incorporate large datasets into the analyses, while also developing an understanding of how variability in rockmass quality, induced stress, structure, or stope orientation could affect stope stability.  This paper presents the fundamental principles of the Stability Graph method, the Python script and workflow, and two case studies to demonstrate the utility of the tool.

Oct 1, 2024

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By J. E. Nesset

"As an alternative to conventional dewatering by vacuum filtration and oil-fired rotary dryers, Brunswick Mining conducted extensive pilot-scale testwork on its copper, lead, zinc and bulk concentrates using a Larox Oy (Finland) automatic pressure filter. The results showed that pressure filtration readily produced final cake moistures of 6-8.5 per cent on this very fine sulphide material.An in-depth analysis examines pressure filtration in terms of metallurgical performance and projects energy savings of 78 per cent for pressure filters over the current dewatering operation. Potential energy and operating cost reductions are also estimated.IntroductionVacuum filters followed by oil-fired rotary dryers are one of the most common means of dewatering mineral concentrates. They represent, however, a level of technology which is exceedingly wasteful in terms of manpower, space utilization equipment and fossil fuel dependence. In addition, the use of thermal dryers is leading to increased environmental concerns both in plant and out.These were the primary factors which prompted Brunswick Mining to consider alternative dewatering methods as the existing equipment came up for replacement and upgrading. In late 1979, company engineers were encouraged by automatic Larox pressure filters seen at several Scandinavian operations. Subsequent laboratory tests by the manufacturer (Larox Oy of Finland) on several concentrate samples were sufficiently promising for Brunswick and Noranda to lease a trailer mounted filter-lab unit and a technician from Larox for a five-week period. Extensive on-site testwork on all four Brunswick concentrates (zinc, lead, copper and 'bulk' lead-zinc) confirmed the potential of pressure filtration."

Jan 1, 1982

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

"With the plethora of cable bolts on the market, geotechnical engineers can be baffled by the differences in performance claims from the manufacturers but perhaps more importantly they are sometimes at a loss in making an optimal selection matching behaviour with a particular site condition. To this end a new testing methodology has been developed that can cater for the varying types of cable bolt behaviours. The methodology is based on the laboratory short encapsulation pull test (LSEPT) as recommended in the British Standard and overcomes several deficiencies such as cable rotation. Of most significance however, is its inability to measure the post-peak residual performance of high load transfer capacity cables and consequently, there is an inference that these cables may be susceptible to sudden anchorage failure with relatively little yield. This paper details the results of anchorage performance tests of a range of cable bolts and the differences in performance with rock strength and drill hole diameter.INTRODUCTIONA research project was undertaken to develop a new laboratory-scale test apparatus to study the axial performance of fully grouted cable bolts that are used in the Australian underground coal mining industry. Work by Thomas (2012) and others in recent years found there were a number of deficiencies in the testing methodologies making it difficult to determine and compare the performance of the dozen or more different types of cable bolts on the market. This has meant that geotechnical practioners have been hamstrung in optimizing the design of ground support systems in underground environments that are increasingly more arduous.A cable bolt is a flexible tendon consisting of a quantity of wound wires that are grouted in boreholes at defined distances between holes in order to provide ground reinforcement of excavations (Hutchinson & Diederichs, 1996). They were initially introduced into the underground hard rock mining industry in the 1960s (Thorne & Muller, 1964) and since the early 1970s have been brought to coal mining operations."

Jan 1, 2015

By M. Kucharski

The model of the Outokumpu direct-to-copper process deals with a steady-state process the parameters of which do not depend on time. To give a prediction for the process outcome, "a modified black box" method, which ignores most of the chemical reactions in the furnace, was used. This method takes input and output parameters into consideration. The presented model describes the Outokumpu direct-to blister process in the form of the set of linear equations which give mass and enthalpy balances as well as the distribution of elements between blister copper and slag. However, only major substances where quantities in the feed charge exceed a certain level (for example 0.5 kg/ lMg of smelted concentrate) are taken into consideration. Minor elements are distributed among slag and metal phases in a different way. Some of the equations are derived from distribution coefficients. The value of distribution coefficients can be calculated from plant production data.

Jan 1, 2007

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By J. Y. Kim, Kenneth Stowe, Stephen Chryssoulis

"A series of flotation tests was carried out on Brunswick Mining ore with various pH modifiers (soda ash, lime, KOH) and added ions (ferric, nitrate, sulphate) in the copper lead rougher circuit. The main objective was to identify downstream effects on sphalerite activation and subsequent zinc rougher flotation. Some significant differences in zinc flotation were obtained. Most notably, soda ash and nitrate ions had a positive impact and ferric ions a pronounced negative effect on selectivity.Selected products from the flotation tests were deslimed at 400 mesh, washed with methanol, air dried, placed in teflon vials purged with nitrogen and stored at -15 degrees C. Numerous liberated sphalerite and pyrite particles were selected under a stereoscope and placed in rows on indium foil. The surface compositions of the particles were analyzed with an innovative laser probe (LIMS). The very small analysis area of the LIMS enables the surfaces of individual grains to be characterized. In addition, the rapid analysis time allows a statistically significant number of grains to be analyzed quickly.Surface lead appears to play a major role in zinc activation/flotation. Possible mechanisms are proposed to explain the variations in metallurgical performance at the different test conditions.IntroductionAlthough the bulk composition of mineral grains is an important consideration for the mineral processor it is ultimately surface composition and topography (edges and dislocations preferred sites for reactions) that control reactivity in flotation and cyanidation (passivation, encapsulation and preg-robbing). Determination of the surface properties of particles from process streams poses a particular challenge for the surface chemist for a variety of reasons, including:"

Jan 1, 1994

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By T L. Horsley

This paper deals with the drilling and blasting methods employed at the Cassiar mine, which is located just south of the B.C.-Yukon border. It covers both the "pit" and "peak" mining operations. Specific problems, such as working in frozen ground, are discussed, and the breaking characteristics of the various rock formations are outlined. The paper concludes with a brief mention of the equipment used in the operation, as "~ell as an outline of the breaking costs. Introduction T HE Cassiar asbestos mine is located just south of the British Columbia -Yukon border high on a spur of McDame mountain. Chrysotile asbestos fibre occurs in a faulted enlargement of a serpentine sill lying conformably be-tween a series of sedimentary beds and volcanic flows which dip at 45 degrees into the mountain. One end of the orebody is eroded by a cirque in which a layer of permanently frozen ore and waste talus lies at the end of the mining benches. The topography at the mine is steep, with no flat areas. Roads, dumps, and areas for crushing,

Jan 1, 1965

By Jerry Handford

Investing in the Development of our Future Workforce ?Collaborative partnerships with educational institutions, industry associations, governments and other businesses. ?Programs: »Co-op / Discipline Student Program »Trades Development Initiatives »Operator Training Programs »General Student Program »Careers Next Generation / Community Careers Co-operative

May 1, 2006

By R. A. (Dick) McIvor

"It is important to ensure that the basic mine hoist plant design fundamentals are incorporated into any new mine hoist plant project before detailed design engineering is commenced. Some of the basic design fundamentals to be considered are: hoist rope fleet and flight angles for good hoist rope coiling, hoist rope harmonic frequency study to ensure that the hoist rope does not run at full speed at a rope resonance frequency, head frame and shaft clearance diagrams to establish the optimum positions for the loading and dumping of the shaft conveyances, access in the head frame and shaft collar for hoist rope and shaft conveyance installation and removal. Failure to consider the hoist plant fundamentals before detailed engineering commences will result in extra costs for hoist plant redesign or a significant increase in operating and maintenance costs for the mine due to increased hoist plant downtime to perform tasks and a lower mine operating efficiency. INTRODUCTION The mine hoisting plant is the most critical single line component in the operation of a shaft sinking operation or a permanent installation. Bad decisions in the design and selection of the hoist plant equipment can significantly add to the operating costs and up-time in the operation of the mine. Mine hoisting plant equipment installed costs represent approximately 5 to 8 percent of the capital cost of a new mine, yet price sometimes becomes the deciding factor for procuring the hoist plant components, sometimes selecting used equipment that may compromise the design and maintainability of the mine hoist plant. Mine downtime can cost upwards of $100,000 per hour and it will not take a very long time to eat up all the so-called savings on hoist plant equipment purchases. This paper will provide guidelines for the design, selection, installation and maintenance of mine hoist plant equipment with the objective to having the right mine hoist plant with the highest operational availability and best maintainability. PRELIMINARY DESIGN INFORMATION Before any engineering commences, the following information needs to be obtained to allow the preliminary sizing of the hoist plant equipment: • Shaft depth: The shaft depth will influence the hoist rope selection based on the material and personnel loads anticipated for the mine design. The shaft depth will also influence the maximum speed of the shaft conveyances. • Annual production: The desired annual production will influence the required payload sizing with allowances for maintenance and inspections of the hoist plant equipment."

Jan 1, 2019

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world's primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By V. ?. Chanturiya, G. P. Dvoychenkova, ?. Ye. Kovalchuk

"Several mineralogical investigations have revealed the composition of modified kimberlites and the mud generated during treatment of diamonds, which contains up to 50% clay minerals (e.g., talc, talcsaponite, chlorite-saponite, Na-saponite) and X-ray amorphous phase. We investigated the composition of the natural diamond surface in relation to the diagnosed minerals and established the sequence and conditions for mineral formation on the crystal surface under kimberlite processing conditions. This article suggests a method to destroy and further dissolve minerals on the crystal surfaces using water system electrolysis products, which makes it possible to restore the diamond hydrophobic properties. The application of chemically treated water in the foam separation cycle under the conditions of high recovery of diamonds made it possible to increase the content of the factory concentrate by 8.0%.INTRODUCTIONThe high content of the modified minerals in the kimberlite ore results in the formation of hydrophilic slicks on the surface of the crystals which decreases the diamond’s hydrophobic properties and increases the losses thereof in the process of grease and foam separation to 20-30% (Kurenkov, 1957; Chanturiya et al., 1998, 1999, 2005; Duikarev et al., 2000).The previous researches have revealed the fact that the prospective way of solving the problem of intensity of mineral impurities formation on the surface of the crystals and the increase of concentration parameters is reached due to application of physical and chemical stimulation techniques on the solid and liquid pulp (Stricland-Constable, 1971; “Improvement of the technology…”, 2006; Makarskii, Adodin & Tarasova, 2011; Chanturiya, Dvoychenkova & Trofimova, 2012). However, the main task of investigations to stipulate the objective achievement is the studying and justification of the reasons of the diamond surfaces covering by the mineral slicks"

Jan 1, 2016

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005