Search Documents

By J. S. Redpath

Eighty feet of overburden, thirty feet consisting of fine, water-bearing sands, was encountered during the construction of a shaft collar for Chimo Gold Mines Limited at its Louvicourt, Quebec, property. This paper describes the excavation and construction methods used on the project. Open-cut methods, a sheet pile cofferdam, chemical grouting and special blasting methods were used during excavation. Concrete placement was hampered in the lower portion by a heavy water flow, and aided in the upper portion by an unusual method of form bracing. Plant and • pum11ing facilities are also described.

Jan 1, 1966

By F. Nava-Alonso, A. Uribe-Salas, C. Rodriguez-Rodriguez

Ozone has been proposed to pretreat refractory ores before the cyanidation process for precious metals extraction. As pyrargyrite is one of the silver species most common in Mexican refractory ores, the ozonization of this silver sulfide was studied. The effect of pH and ozone concentration on silver dissolution was evaluated by means of a factorial experimental design. Two levels of sulfuric acid concentration and ozone in gas concentration were evaluated: 0.18 and 0.72 mol/L of acid and 0.054 and 0.077 gO3/L, respectively. The highest silver dissolution was obtained when using the higher acid and ozone concentration.

Jan 1, 2011

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By J. E. Nelson

This paper will examine the problems inherent in matching grinding mills with electric motors through connecting elements such as clutches. Emphasis will be on the uncertainties of mill torque and power demands and the need to recognize these if dependable, safe designs are to be obtained.

Jan 1, 1972

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

"Le présent article porte sur la diminution des rejets de concentrateurs produits durant l’exploitation et le traitement des minerais métalliques.Le minerai dilué envoyé au traitement a, très souvent, un certain pourcentage du stérile qui affecte directement la rentabilité des opérations souterraines et amplifie l’impact négatif sur l’environnement. Les essais de la séparation du stérile et du minerai effectués en milieu dense sur quelques types de la minéralisation d’or, ont démontré les deux possibilités qu’offre cette technique:• Dans le cas d’un minerai riche, il a été possible de séparer la part importante du toutvenant (minerai dilué contenant le minerai et le stérile) provenant de la dilution, tout en ayant un taux de récupération élevé (supérieur à 96%).• Dans le cas d’un minerai ayant une teneur sub-économique à cause d’une dilution importante, il est possible de produire un concentré ayant une teneur économique à l’entrée de l’usine de traitement, en éliminant une partie du tout-venant.En plus la séparation du stérile peut accroître, en outre, la rentabilité de l’exploitation minière, car le fait d’éliminer la partie de stérile le plus tôt possible diminue certains coûts (transport, traitement et autres). On conclue que la pré-concentration du minerai (séparation du stérile et du minerai) est probablement une seule solution actuellement étudiée qui diminue l’impact environnemental de la mine, sans avoir des conséquences négatives sur la rentabilité de l’exploitation souterraine."

Jan 1, 1997

By M. H. Ali

Codelco, a multi-process primary copper producer, is undertaking a full life cycle inventory (LCI) of all its commercial products based on copper and molybdenum. During this work, many questions have surfaced regarding the contribution of process unit design to specific aspects of a product's LCI and, more importantly, how such designs could be improved using a life cycle perspective. Management strategy efforts were undertaken to improve the LCI footprint, however it was found that the corrective actions were almost impossible to apply at the operation level in plant, given the ongoing timing pressures of extractive mining, and costs saving priorities. Additionally, it was found that most of the important comparative differences between operations had structural reasons. In this circumstance, the LCI practitioner group from 1M2, and the environmental managers from Codelco, decided to shift its efforts to place the critical LC1 aspects to the design process of future developments. Hatch Associates has developed unique tools in their Sustainable Plant Design (SPD) package that compliment and enhance LCA methods; these effectively drive sustainability into the heart of the design process. By using LCA and SPD in a project design phase, you cannot only address potential hotspots, but also decide on materials, location and size of certain facilities to optimize for energy efficiency. Moreover, you can avoid the shifting of environmental burdens upstream or downstream within the plant and finally it is extremely useful in identifying opportunities for greenhouse gas reduction.

Jan 1, 2007

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973