Search Documents

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By Morris J. Viljoen, David R. Young

"The zone of economic interest at H.J. Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At least three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5lBeatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more -distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By J. W. Reynolds

"The use of approved fire-resistant hydraulic fluids in equipment operating underground was made mandatory in British Columbia by amendment to the Provincial Mines Regulation Act effective January 1, 1975. This paper covers the action taken to achieve this, in the largest underground metal mine in British Columbia. Some evaluation of costs and effects based on experience to date is included.BackgroundAn amendment to the Mines Regulation Act of the Province of British Columbia was passed in July 1974 as follow s: "" Rule 111 (b) Hydraulic Fluids. After the first day of January 1975, all hydraulic fluids used in equipment operating underground shall be of a fire-resistant type accept able to the chief inspector.""Unquestionably, its intent was justified as a safety improvement measure. The list of fires in mines involving machinery where hydraulic fluid was a factor in the fires is long and sobering. In British Columbia, in a 22-month period from 1972 to 1974, there were six fires in metal mines resulting in extensive equipment damage and injury to four workmen. Nevertheless, no provision was made for research or development of systems modifications compatible with conditions encountered in B.C. and, as late as June 1977, the Mining Association of British Columbia continued to argue that fire suppression systems should be considered sufficient until a universal suitable hydraulic fluid could be developed. The sole concession was to issue permits for continued use of mineral oil in equipment bought prior to 1975 in order to allow producing operations to continue. The burden of developing the necessary technology was laid on the industry.The Sullivan Mine at Kimberley, the largest and longest established underground mine in the province, and Cominco's most important source of ore s for its smelter at Trail, B.C., was at the outset of a conversion from conventional to trackless mechanized mining methods in pillar recovery operation s. Introduction of fire-resistant hydraulic fluid s had to be done in a period of change, in many instances on equipment for which no data existed, and called for research which had to be done while retraining the work force.The introductory phase is complete. All equipment is on FRF, the requirements of Rule 111(b) are being satisfied, and a number of research and development programs continue."

Jan 1, 1980

By Jacques Ouellet

Outline What is Microwave energy Investigation of transparency of 40 minerals Melting of Andesite in a MW oven Numerical modeling /Computer Simulations o FEM analysis ?? Some laboratory experiments o Particle Modelling Mw Application to Rock Breakage o A MW Rock Drill Prototype Conclusions What is Microwave energy Microwave energy is an electromagnetic wave consisting two electronic & magnetic wave traveling perpendicular to each other and transporting energy with the speed of light.

May 1, 2008

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time, over 140 million tons of waste and low-grade material has been placed on the mine waste dumps. Laboratory and in situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electro winning plant. The plant, which was commissioned in October 1986, was designed to process 3000 USGPM of dilute copper solution to produce 5000 tons per year of high-quality cathode copper.This paper deals with the start-up and initial year of operation of this plant. The three areas: leaching, solvent extraction, and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to the Gibraltar operation.The Leaching CircuitThe mine waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dumps. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and dissolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the sulphides and solubilization of the copper into the acid solution.For the bacterial action to occur the dumps must be near the ideal pH of 1.9 to 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory leaching tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate (Fig. I).The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate (Fig. 2)."

Jan 1, 1988

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013

By Y. Wang, J. D. Miller, C. L. Lin, Virginia Tech

Conventional flotation machines are typically limited to a particle topsize of 150-200 microns due to inherent constraints created by the pulp and froth phases. To overcome these limitations, a novel fluidized-bed flotation system called the HydroFloatTM Separator has been developed specifically for the purpose of floating coarse particles containing only small amounts of exposed hydrophobic minerals. Over the last decade, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3,000 microns diameter. More recently, sulfidebased test work has shown that this novel device is also capable of recovering metalliferous values at a grind size that is much coarser than currently used in industrial concentrators. In the current study, high resolution X-ray microtomography (HRXMT) was used to experimentally compare the degree of exposed grain surface area necessary to recover coarse particles using the HydroFloatTM technology to that attainable using a traditional mechanical flotation cell. The data indicate that exposed grain surface area is a critical factor for coarse particle flotation. For the gold-bearing sulfide ore examined in this study, the HRXMT data suggest that near complete recoveries of coarse (850x500 µm) multiphase particles containing as little as 1% exposed grain surface area were realistically attainable using the HydroFloatTM technology. As such, this new technology may offer a unique opportunity for increasing concentrator capacity by increasing the primary grind size needed for rougher/scavenger separations.

Jan 1, 2016

Safety Leadership The management and leadership of a mining operation is a challenge at all times. The pressure to make production, safety, and environmental goals is intense. At some point mining cycles will put every operator into periods of time where economic issues seem to over-ride all other concerns. This is when leadership is most needed.

May 1, 2009

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By L. K. Nenonen

"Given the properties, locations and quantities of material to be hauled and the dump locations and capacities, the designer wishes to select the type and number of trucks and loading equipment required. Accordingly, software is being developed to assist in creation of the equipment, material and road network data bases, in selection of equipment, materials and road networks from these data bases, and in evaluation of the expected productivities both in a rapid, non-interactive, approximate fashion and a more detailed interactive fashion which permits the user to act as superintendent, if he so chooses. The basic technology has been developed and applied to an open-pit copper mine and is being refined and generalized for oil sands and coal mining applications.BackgroundA set of mathematical and interactive computer models are under development to aid in the selection of equipment and operating policies for an open-pit oil sands mine being planned by Canstar Oil Sands Ltd. This paper describes the computer models being developed of truck haulage systems. Although the interactive truck haulage model is based primarily on a model developed by the National Research Council in collaboration with Glenayre Electronics Ltd. of North Vancouver and Lornex Mines Limited(2).(3l, substantial changes and improvements are being incorporated to greatly increase its generality re equipment types, road network characteristics, dispatching and supervisory policies, etc. Although this paper is principally devoted to the truck haulage model, discussion is included concerning its interactions with other models."

Jan 1, 1982

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By E. Kouame, M. D. Everell, D. Hodouin, T. Kasongo

"To properly operate a mineral beneficiation plant it is often necessary to have systematic evaluations of the performances of a piece of machinery, of one of the processes or of the plant as a whole. The state of a process can be described from a collection of data: flow-rate values, particle-size distributions and chemical compositions of the various streams of the circuit studied.However, the obtained raw data are generally redundant and inconsistent from a material balance viewpoint, due to natural disturbances, sampling errors, unreliable instrument readouts and laboratory analysis inaccuracies.BILMAT is a computer program which upgrades mineral processing data, adjusting them in a least-squares sense in order that they may verify material conservation constraints. As a consequence, the program is able to calculate the best values of unmeasured flow rates (such as. circulating load ratios). BILMAT is a very general program in the sense that it can accept various data from any type of mineral processing circuit, and its usefulness is demonstrated here for three processing circuits of a pyrochlore concentration plant: grinding, desliming and flotation.IntroductionComputation of the material balance around any metallurgical process, that is the determination of stream flow rates and composition. is a basic step in its evaluation. In spite of the simplicity of the physical laws of mass conservation. and of the very fundamental need to know the flow of components around a process. it appears, particularly in mineral processing. that material balancing is quite often a difficult task. The reasons for this involve the problems associated with collecting measurements in mineral dressing plants. They are generally poorly instrumented and invariably data must be collected through hand sampling. Due to the heterogeneous nature of the streams, segregation occurs and samples are often not adequately representative, a problem made worse by the lack of circuit sampling facilities, which are often completely ignored by plant designers. Furthermore, the nature of the measurements to be performed (for instance particle size distributions in the fine range) frequently gives inaccurate results."

Jan 1, 1981

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016