Search Documents

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By Keith Spence

"The notion of ""value"" has always been a subjective and contentious issue. Indeed, Value is in the eye of the beholder. There are varied methods and practices for valuing property, as there are industries in which they are applied. For example, there are ""replacement value"", ""insurance value, ""salvage value"", ""appraised value"", ""book value"" and ""fair market value"", to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered, are included the following: the Discounted Cash Flow Approach, the Cost Approach, the Option Pricing Approach and Market Comparables Approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIMVal committee expects that its final report will form the basis for a standard Canadian Code for the valuation of mineral properties."

Jan 1, 2003

By V. Budinsky

In recent years the global mining industry has addressed its social and environmental responsibilities and numerous factors have contributed to this. Corporate Social Responsibility (CSR) is an important part of mining company strategy for practical implementation of the goals of sustainability, transparency, accountablity and good relationships with stakeholders:- investors, employees and communities. A key stakeholder for all mining companies is the local community which is affected by the mining operations. Companies must identify the emerging social and environmental trends, study the interests and concerns of various communities, address their needs and maintain a positive relationship. The CSR programmes of Czech coal mining companies are focused on surrounding community initiatives and sustainable responsible business. Mining in the Czech Republic is subject to strict rules and regulations and supervised by the State Mining Authority. Mining projects undergo rigorous approval procedures which encompass all operational measures at the different planning levels ? such as public participation in the authorisation process for mining projects, the application of the Environmental Impact Assessment Directive, environmental sustainability programmes, innovative solutions and flexible options offered by the mining company. One very important part is the preparation of the mining-technology preconditions and developing the integrated planning process in which all socially and politically relevant subjects in the mining operation surroundings are included. In an in-depth debate, all stakeholders may jointly develop the concept, in accordance with democratic principles. The optimally conducted dialogue process needs broad communication bases, including setting up theme-related joint taskforces, together with good moderation and the highly qualified support of technical experts. Using a case study of Severoceske doly a.s. Chomutov (SD Company) and the Czech Coal Group ? Czech leaders in the extraction of brown coal, this paper aims to examine the community development approaches and the CSR effectiveness of large scale mining companies. This paper brings a review of CSR and other such voluntary initiatives in the mining industry's proactive steps to contribute to societal well-being in a meaningful way. Key studies are provided by the projects ? Region with Better Perspective?, ?Stop Dust for Healthy Brezno Village?, ?Clever Heads for the North? and ?Coal Safari?. CSR issues are managed throughout all stages of the mine operation and beyond, long after the mine closes (e.g. post-closure programmes of new landscape, alternatives for reclamation including generation of lakes in former surface mines, conceptualization of industrial heritage). Communities need to be given the opportunity to help themselves through participation in CSR projects rather than being recipients of financial gifts from the company. A fair balancing of interests is the basis of any successful cooperation.

Aug 1, 2013

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By M. Pearson, J. Irvine, L. Mercer, P. Lauzon

Severe service ball valve performance has a direct impact on the mechanical availability of high pressure oxidation and leach plants. The primary function of these valves is to isolate the autoclave for maintenance. Valve failure has historically contributed significantly to the maintenance downtime of these process plants. An understanding of the root causes of valve failures is the first step in increasing the reliability of the severe service ball valves. A rigorous failure analysis practice has been developed by Hatch for investigating refractory failures in furnaces and kilns based on Kepner-Tregoe methodology. The method has also been modified for valve failure analysis. From a root-cause failure tree analysis of each of the valve components, a list of all potential valve failure mechanisms was developed for ranking and evaluation, along with recommendations for further valve development. The purpose of this paper is to present the reader with the modified Kepner-Tregoe method and examples of this analysis.

Jan 1, 2004

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By S. Aram

Product Lifecycle Management (PLM) solutions have been serving as the basis for collaborative product definition, manufacturing, and service management in many industries. They capture and provide access to product and process information and preserve integrity of information throughout the lifecycle of a product. Efficient growth in the role of Building Information Modeling (BIM) can benefit vastly from unifying solutions to acquire, manage and make use of information and processes from various project and enterprise level systems, selectively adapting functionality from PLM systems. However, there are important differences between PLM?s target industries and the Architecture, Engineering, and Construction (AEC) industry characteristics that require modification and tailoring of some aspects of current PLM technology. In this study we examine the fundamental PLM functionalities that create synergy with the BIM-enabled AEC industry. We propose a conceptual model for the information flow and integration between BIM and PLM systems. Finally, we explore the differences between the AEC industry and traditional scope of service for PLM solutions.

Aug 1, 2013

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016