Search Documents

By Lifeng Yang, Xiang Zhang, Liang Yuan, Yonghui Wang, Bing Hou, Mian Chen, Rixing Zhang

Large-scale hydraulic fracturing technique has been widely applied to the development of shale gas reservoirs, where the interaction between natural fractures and critical fracture zones has substantial impact on the propagation of hydraulic fractures. Therefore, it is of significant importance to understand and experimentally verify such mechanism. To reach this end, tri-axial fracturing tests were implemented on 400mm×400mm×400mm block samples collected from Longmaxi shale outcrops. The interplay between hydraulic and natural fractures was investigated during the tests, factoring in the role of pump rate in affecting the created fracture network. Based on the experimental results, the critical fracture zone, defined as the weak formation zone nearby the wellbore created by staged pressure implementation that is observed rapid fracture propagation upon next stage of pressure increase, was thoroughly investigated. The analysis illustrates that given the high brittleness of the shale formation, abundant critical fracture zones are generated around natural fractures with pressure building up at a relatively low pump rate. As the pump rate increases, hydraulic fractures initiate and come into play with critical fracture zones, implying emergence of a large number of micro-cracks. A changing pump rate modifies the way of interaction between hydraulic and natural fractures and the subsequent formation of fracture network. Long term fracturing fluid injection with relatively low pump rate below the activation of critical zones is suggested. Also proposed is appropriate timing when applying a specific pump rate that will contribute to the improvement of hydraulic fracture propagation.

Jan 1, 2015

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By H. Rozovsky

This paper deals with the large iron ore concentrating plant owned by the Iron Ore Company of Canada. The plant is part of the Carol Project, which is being developed in the Wabush area of western Labrador. The mining and milling operations were officially opened in July of this year. The handling of fine material has always been considered a serious operational problem. The crushing, grinding and sizing of 50,000 tons of iron ore per day, in a dry state, could present sizeable problems in maintenance and orderliness. The operation, as a whole, embraces many recent developments in the iron ore industry. Mining operations include the latest techniques of jet piercing and blasting. Primary crushing involves a single crusher, which handles the complete production. Grinding of the ore includes the latest concepts of dry autogenous grinding in air-swept mills. The actual concentration of the ore is per-formed, in the wet state, by the use of spiral concentrators, with provision for possible flotation or magnetic separation, if required. The upgraded concentrates are either stored or pelletized, prior to shipment by rail to Seven Islands.

Jan 1, 1962

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By Derrick Hunter, Pat Feighan, Keith Chrystall, David Wells

"Equipment which may be remotely operated, has some degree of on-board intelligence, and which for periods of time may operate autonomously, is referred to as telerobotic. Recent advances in electronics, computers and hydraulic equipment have dramatically reduced the cost and simplified the process of converting standard industrial equipment to telerobotic control. The benefits of telerobotic equipment include improved safety by removing the operator from dangerous situations, reduced maintenance costs and increased productivity. This technology has been proven in various military, nuclear, and police applications.The surface mining industry has expressed an interest in automation and is characterized by a willingness to use remotely operated equipment, however, the majority of telerobotic equipment currently in use is experimental or prototypical. Potential applications of telerobotic equipment for surface mining include remote operation of equipment near dangerous high walls and other unsafe areas, utilization of robotic trucks for routine hauling operations, and control of jointed equipment. In addition, component technologies of telerobotic systems are relevant to various forms of condition monitoring, operator feedback systems, and vehicle positioning.Attention must now be directed toward resolving more complex problems associated with enhancing feedback to the operator, improving the man/machine interface, and ultimately, improving efficiency. Removal of the human operator from the work site introduces significant complications in replacing the sensory inputs that an operator normally uses to efficiently run his machinery. These can be difficult to define and even more difficult to replicate remotely and may include restrictions pertaining to vision, hearing, and touch.In cooperation with Defence Research Establishment Suffield and the Alberta Research Council, Robotech Industries Ltd. is pursuing the development of additional technologies to further enhance an operator’s ability to control remote telerobotic equipment. These developments include a head-mounted display, additional control station displays and improvements to coordinated motion control software. Prototypes of these developments are expected to be completed and tested by the fourth quarter of 1997."

Jan 1, 1996

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

During the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits. However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses haw not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently am poorly doc-umented, the use of these terms is reviewed. Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco's Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delin¬eation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study. The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit by 39.27% and 45.41%, respectively, and that of the 6 m wide deposit by 12.84% and 11.55%. As the impacts of ore loss and those of dilution on the net present value am almost identical in these simulations, we could, in practice, assume a 50/50 split between dilution and ore losses in such a case. These results do no take into account the effects of local optimization measures taken at the mine production level (blasthole sampling near stope limits, etc.) The potential impacts of geological and sampling uncertainties in terms of lower NPV justify and require more systematic efforts to ensure that deposit appraisal work and feasibility studies are adequate to optimize company revenue and competitive returns to investors from mine production activities.

Jan 1, 2005

By Peter Rubie

For many years, optimising the relining of hard rock grinding mills has been complicated by: ?? the large number of variables; ?? the low frequency of relines (slow feedback loop); ?? the potential economic risk associated with some changes. A technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared. This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world?s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability. This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables. The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant.

Jan 1, 2012

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970