Search Documents

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

By John A. Teeter

"A SHORT WHILE AGO I enquired about The Mining Society of Nova Scotia. In all honesty I was apprehensive about addressing such a body if it was highly geared to the technical aspects of discovering and obtaining mineral resources. I was told that this would not be the case. Rather, there would likely be in attendance a broad cross section of people from business, industry and government and from across Canada and the U.S.A. Thus there would be an interest in a free-wheeling discussion of the prospects for industrial development in Cape Breton. Accordingly - being one who hates to miss an opportunity - I intend to exploit the invitation of your executive by being, over the next short while, frankly promotional. I would like to talk about what I consider to be some of the most important attributes of Cape Breton for industrial development and identify some of those prospects. Secondly, I will quickly review some of the things the Cape Breton Development Corporation is doing these days to stimulate some of that industrial development."

Jan 1, 1972

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

By W. E. Roscoe

The probability of making an exploration discovery in Canada can be calculated from Derry's (1970) data on exploration expenditures and number of discoveries over the last nineteen years. Considering an average exploration "try" to be $30,000, the probability of a discovery with one try has decreased tenfold from about 0.01 in 1951 to 0.001 in 1969. A plot of these probabilities can be extrapolated to the future, giving a 1969-71 three-year average probability of 0.00096 with 90 per cent confidence limits of 0.00042 and 0.00153. Using this probability, various calculations can be made, such as (1) the probability of making at least one discovery for any given exploration expenditure, (2) the probability of ultimate ruin or survival of the exploration investment process and (3) the expected value of an exploration investment. There is a critical minimum amount per discovery that must be re-invested in exploration, no matter how large the original investment is, for exploration to survive at all in the long run. Currently, this critical minimum is $31,200,000 with 90 per cent confidence limits of $19,600,000 and $71,400,000.

Jan 1, 1971

By Colin E. Dunn

The high mobility of gold within the plant kingdom results in detectable accumulations of gold in many plants. Concentrations vary within individuals, among species, and with seasons. From an evaluation of the chemistry of easily acce sible organs of common pecies in the northern forests, it is concluded that alder twigs (or leaves) and conifer bark scales are the vegetation components of greatest use in the earch for concealed gold mineralization. Maximum anomaly enhancement is obtained from twigs collected in the spring. Examples are given of urvey conducted in the La Ronge Domain using 1) jack pine bark (A nglo-Rouyn and Upise Lake areas) ; 2) alder twig (McLennan Lake) ; 3) black spruce bark (Rod Zone near Mallard Lake, and at Waddy Lake) ; and 4) multi-media (Tower Lake). At the latter two sites gold-bearing till is blanketed with late glacial material. Gold enrichment in the plants suggest that the roots are ab orbing gold from the underlying till. Complex processe control the uptake and retention of gold in plants. An understanding of these processes pem1its biogeochemistry to assist in locating near- urface mineralization .

Jan 1, 1986

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By Douglas A. Grieg

THE EXCUSE for producing still another paper dealing with the oilfields of the Middle East is the overwhelming importance of this area to everyone, both inside and out of the oil industry. Figure 1 shows the area defined as the Middle East for the purpose of this paper. No description of what constitutes the Middle East is generally acceptable to everyone and, in fact, in many parts of the world it is referred to as "Western Asia". At the time ?the writer went to work as a geologist in the Middle East -this was in 1926 -there were just three known oilfields, namely, Hurghada in Egypt, Naft Khaneh in the Transferred Territories of Iraq, and Masjid-i-Sulai-man in Persia. Their combined producing rate at that time was around 100,000 barrels per day. Toda y, just thirty years later, some forty-two fields have been proven to exist, and a recent discovery in Syria -if commercial -may add one more to the list. Producing rates at the end of last year ( 1956) were approaching four million barrels per day. This sizable figure re presents nearly 23 per cent of the total Free World's production. What is more important still, something over 70 per cent of the Free World's proven oil reserves are known to exist in the subsoil of the Middle East.

Jan 1, 1957

By T. Verdel, Y. Gunzburger

Rockfalls are major and essentially unpredictable sources of danger, particularly along transportation routes (roads and railways). Thus, the assessment of their probability of occurrence is a major challenge for risk management. From a qualitative perspective, it is known that rockfalls occur mainly during periods of rain, snowmelt, or freeze-thaw. Nevertheless, from a quantitative perspective, these generally assumed correlations between rockfalls and their possible meteorological triggering events are often difficult to identify because i) rockfalls are too rare for the use of classical statistical analysis techniques and ii) all intensities of triggering factors do not have the same probability. In this study, we propose a new approach to investigate the correlation of rockfalls with rain, freezing periods, and strong temperature variations. This approach is tested on three French rockfall databases, the first of which exhibits an outstandingly high frequency of rockfalls (approximately 950 events over 11 years), whereas the other two databases are more typical (approximately 140 events over 11 years). These databases come from (1) the national highway RN1 on La Réunion Island, (2) a railway in the Bourgogne-Franche Comté region, and (3) a railway in the Auvergne region. Whereas a basic correlation analysis is only able to highlight an already obvious correlation in the case of the “rich” database, the newly suggested method appears to detect correlations even in the “poor” ones. Indeed, the use of this method confirms the positive correlation between rainfalls and rockfalls on La Réunion Island database. This method highlights a correlation between cumulative rainfalls and rockfalls in the Bourgogne region, and it detects a correlation between the daily minimum temperature and rockfalls in the Auvergne region. This new approach is easy to use and also serves to determine the conditional probability of rockfall function of a given meteorological factor. This approach will help to optimize risk management in the studied areas based on their meteorological conditions. Nevertheless, even if some rockfalls are correlated to meteorological factors, other seems to occur independently of these factors, which highlights the unpredictability of rockfall hazard.

Jan 1, 2015

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By David M. Knowles, R. Gordon Gastil

"The Precambrian sedimentary series of the Labrador geosyncline, including iron formation, extends into southwestern Labrador and adjacent Quebec. The iron formation consisted of primary oxide, silicate, and carbonate facies which were deposited simultaneously in an irregular basin in response to migratory environmental conditions. The iron formation isochemically recrystallized to coarse-grained quartz-iron oxide, iron silicate, and quartz-iron carbon-ate rocks during prolonged regional metamorphism. The rocks are deformed on two deformation axes intersecting at large angles, and are characterized by isoclinal to recumbent folds. Parts of the formation have been profoundly affected by a post-metamorphic leaching and oxidizing environment."

Jan 1, 1959

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015

By R. A. Wyman

A comparison of the amount of minus-28-mesh product produced by a standard grinding test procedure is provided for 45 non-metallic materials. The percentage of product, the weight of product per unit of energy used and the weight of product per mill revolution are shown. The results exhibited excellent reproducibility and demonstrated an accurate comparison of grindability for non-metallic materials.

Jan 1, 1977

By M. D. Vance, G. R. Corbett, S. D. Butt

Surface wave imaging is a relatively new seismic technique that generates subsurface depth images without having to drill boreholes into the ground, and is rapidly becoming a standard tool in non-destructive geotechnical characterization. This paper presents a case study of the application of these surface wave techniques to image shallow abandoned mine workings at the Montague Gold Mines district near Dartmouth, Nova Scotia. This district has numerous steeply dipping narrow vein workings from historical mining activity, and has actively subsiding and collapsing crown pillars. Due to the rugged conditions at the site and the relative narrowness of the openings (often less than 1 m), a surface seismic system was developed that had improved portability and lateral resolution over other available seismic imaging systems. Seismic surveys were conducted over two sites where independent evidence indicated the presence of shallow mine workings. At one site, a comparative gravity survey was also conducted. The seismic data was processed to generate velocity vs depth images. Overall, the velocity images show vertical zones of zero velocity in the same lateral positions where historical mapping, current subsidence and gravity surveys indicate the presence of steeply dipping workings. Further, the velocity sections are consistent with the thickness of the till cover at each site and the possible weakening of crown pillars at one of the sites.

Jan 1, 2005

By G. W. Evatt

This paper presents the scientific framework underpinning the Resource Valuation and Optimisation Model (RVOM). The RVOM is a Real Options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty. The three key outputs from the RVOM are: Valuation, Optimal Decision and Probability of Decision, where a decision can include any combination of: normal operation, expanded operation, care and maintenance, and abandonment (and variants thereof). This paper presents a clear example of the RVOMs usage to a case-study gold mine.

Jan 1, 2011

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961