Search Documents

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By H. J. Chalmers

THE H.B. MINE and concentrator are located in the Nelson Mining Division of British Columbia, on the north side of the Sheep Creek valley about seven miles southeast of the town of Salmo. It is an operation of The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), which has its metallurgical plants at Trail, about 25 miles west. The property was originally staked about 1907 by Horton and Benson, whose names are commemorated in the designation "H. B." Up until 1927, a considerable amount of development work was done in the upper levels by various companies. Cominco purchased the ?property in 1927 and carried out intermittent work until 1946. Following this, an extensive surface diamond drilling programme and a subsequent underground exploration were undertaken. Sufficient ore was outlined 'to warrant the construction of a 1,000: ton concentrator. This was started in April, 1952, and completed by the spring of 1953. However, because of adverse base metal market conditions, operation was deferred until May, 1955.

Jan 1, 1957

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By J. Defreyne

CESL has developed a proprietary hydrometallurgical process for base metal concentrates, notably those of copper and nickel. The process is based on pressure oxidation (PO) of the sulphide minerals, which is done at elevated temperatures in mixed sulphate-chloride liquor at about pH 2 ? 3. The process achieves maximum oxidation of the metals whilst minimizing sulphur oxidation to sulphate. Almost all base metal sulphide minerals are efficiently treated under these conditions. In the case of copper minerals, pressure oxidation does not generally put the copper into solution, because of the relatively high pH prevailing in this process. Therefore, PO is followed by an acidic leaching stage, which specifically aims at maximum copper dissolution with minimal leaching of iron. The overall copper recovery is largely determined by the efficiency of this stage. The process has low capital and operating costs, partly because there is minimal use of acid or neutralizing agents for iron dissolution or precipitation, respectively; this is achieved by minimizing iron leaching during both the oxidation and leaching stages. Iron sulphides in the feed concentrate deport almost entirely to the solid leach residue as hematite, which has superior handling characteristics for filtering and washing. Iron minerals play a key role in the process, with pyrrhotite and pyrite having very different responses to the oxidation process. Acid management for the whole process is affected by the iron mineralogy, and the flowsheet is therefore tuned to the specific concentrate.

Jan 1, 2006

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By R. J. Chase, C. Davies

"Abstract- The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilirnajaro International Airport and in close proximity to the towns of Moshi and Arusha . The graphite mineralization is hosted by relatively undeformed linear Proterowic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasibility studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 8o/o graphitic carbon . Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.ln addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence."

Jan 1, 1994

By G. W. Sparkes

The use of CR-39 plastic polymer as a solid state nuclear track detector in the textural analysis of radioactive minerals in geological samples was first described by I.R Basham in 1981. CR-39 autoradiographs provide a detailed, high-resolution image of the in situ distribution of the radioactive minerals within geological samples on both the macroscopic and microscopic scales. This technique is an inexpensive and effective means of obtaining detailed textural information that provides insight into the style of mineralization, its relationship to primary and secondary structures in the host rock, and its association with particular geological features or mineral phases. Although this technique does not provide any information on the identity of the minerals responsible for the radioactivity, the resultant autoradiographs can be used to select regions for further detailed analysis such as petrography, microprobe analysis, or SEM imaging. This paper summarizes the procedure and outlines the appropriate time and materials required for both the exposure and etching of the CR-39 with respect to the intensity of the radioactivity emitted by the geological samples.

Jan 1, 2013

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By R. Poulin, M. R. Samis

Real options valuation is an alternative net present value framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the lowgrade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The real option model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2006

By J. W. Sanger

The establishment of a central steam-heating system in Winnipeg and its inauguration in October, 1924, has attracted a considerable amount of attention. Not only does it excite the curiosity of the engineer, but it has stirred financial and civic bodies throughout Canada to such a degree that there is now a much keener general interest in this particular type of public utility than has been shown heretofore. This does not mean that we may expect a mushroom growth of central-heating systems in all our larger Canadian cities in the near future, but it does mean that the pioneer work which Winnipeg is now doing will undoubtedly be used to guide others in their judgment as to the feasibility of similar projects elsewhere. The success of the municipal hydro-electric system in Winnipeg, and the low rates for electricity resulting therefrom, was without a doubt the most important factor influencing the citizens of Winnipeg to venture into this new field. The events which led up to the central steam-heating proposal in Winnipeg are interesting.

Jan 1, 1926

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016

By A. Holland, T. Krumins, E. Olin, J. F. M. Castilleja, J. Geldart, C. Fleming, I. Jackman

A flowsheet has been developed to treat the flotation tailings from a copper mine in Mexico to recover gold and silver by cyanidation and carbon-in-pulp (CIP). The plant will treat ~15,000 t/day of a 60:40 blend of current flotation tailings and the mine’s historic tailings. The tailings also contain a significant amount of cyanide-soluble copper, and the economic viability of the project is strengthened by recovering most of the copper and cyanide associated with this process. The solution and solid phases in the CIP tailings will be separated in a counter current decantation (CCD) circuit and the CCD solution overflow will be treated by a SART Process. Copper precipitates as a salable copper sulphide product in the SART Process and the cyanide that is associated with the copper complex is regenerated as free cyanide. After SART, a portion of the SART product solution will be recycled to leach to reuse the free cyanide, while the remaining solution will be used as wash water in the CCD circuit. Incorporation of the SART Process in the flowsheet allows the CIP circuit to be operated aggressively as a gold plant, which means most of the silver in solution passes through CIP to SART. Silver co-precipitates with copper in SART and is recovered very efficiently with the copper sulphide by-product. Incorporation of SART also allows the leach and CIP circuits to be operated with relatively high levels of free cyanide, which enhances silver leach kinetics and helps keep copper from loading onto the carbon in CIP. The flowsheet was developed in the laboratory and successfully demonstrated in a fully-integrated pilot plant in 2018.

Jan 1, 2019

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, W. L. Mason, John J. Justen

"A miscible displacement pilot, using a slug of LPG driven by separator gas, was conducted in the Cardium Reservoir of the Pembina Field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gas phase, an .experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to cakulate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones, and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in con-trolling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir."

Jan 1, 1960

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada's imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By E. Krause

The oxidation of Fe(II) with S(IV) and oxygen can be used advantageously in leaching systems requiring both Fe(III) and sulfuric acid; e.g., heap leaching of sulfide-containing ores or concentrates. The oxidation of Fe(II) with SO2/air is several orders of magnitude faster than with air alone; rates of up to ?20 g/L'h were observed at 25°C. The reaction proceeds via an intermediate orange-red mixed-valence Fe(II)/Fe(III) sulfite complex, which is present at an essentially constant concentration throughout most of the oxidation process. The oxidation rate of Fe(II) is approximated by the formula -d[Fe(II)]/dt = k [S(IV)] [02]0'3. The concentration of the mixed-valence complex, and thus the iron oxidation rate, decreases with increasing acidity. Certain impurities, such as SCN- and thiourea, negatively affect the rate. The oxidation reaction 2Fe2 + SO2 + 02 4 2Fe3+ + S042- is accompanied by the side reaction H20 + SO2 + 1/202 4 H2SO4. The side reaction becomes particularly important at low temperatures and whenever the oxygen mass transfer is insufficient with respect to the rate of addition of S(IV). Thus, effective oxygen mass transfer is essential for achieving high oxidation rates with minimal acid formation. The activation energy was estimated as 141 kJ/mol over the temperature range 10-35°C.

Jan 1, 2006

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By S. Power Warren

Introduction It is generally conceded by flotation men that the condition at the surface of a particle of mineral or gangue is the most important factor controlling its behaviour in a flotation cell. Much research work has been devoted to the study of the forces that are active at the surface of the particle and of the effect of the surrounding solution upon these forces. Study of the relationship between mineral or gangue particles and gas bubbles indicates that, in the main at least, flotation is a physical phenomenon. The important factor, that of mineral-gas-bubble attachment, is unquestionably physical; however, modifications may be effected by chemical means, whereby the nature either of the surface of the particle or of the surrounding solution may be changed. For example, the coating of lead sulphide that forms on lead-carbonate ore particles when sodium sulphide is added greatly aids the flotation of the carbonate particles. Without going into the question as to why, under certain surface conditions, mineral particles will attach themselves to gas bubbles whereas under other conditions they will remain unaffected, it may be stated that there are three general conditions in a flotation pulp which control the attachment of the particle and the gas bubble.

Jan 1, 1933

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018