Search Documents

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

By J. Jacob, A. G. Guézennec, F. Savreux, S. Nanaa, M. Delclaud, P. d’Hugues

Mining wastes can contain base and precious metals, but also metalloids and rare earth elements that are nowadays considered as highly critical for the industrial development of the European Union. The development of alternative routes to conventional processing is still required in order to decrease the cost associated with the treatment of these resources, which are more complex in composition and with lower grades. An ecologically acceptable and yet economic alternative for processing of low-grade sulphidic primary ores as well as mining wastes is the extraction of metals using bioleaching processes. The purpose of this study was to test the potential of bioleaching procedures for the extraction of residual metals contained in sulphide-rich tailing wastes coming from a European copper mine. These wastes are mainly composed of pyrite (60%) and contain cobalt (0.06 %) and gold (0.95 g/t). Bioleaching experiments were performed in 2 L stirred reactors in batch mode and in pilot tanks (110L) in continuous mode, using the "BRGM-KCC" bacterial consortia. High metal extractions were obtained (cobalt dissolution > 90%), which confirm that bioleaching is an effective process for this tailings material. Experimental results were used to design a global treatment process scheme and to perform a preliminary economic evaluation, showing good profitability of a hypothetical industrial project.

Jan 1, 2014

By Gregg W. Morrison

"The Craigmont copper-iron skarn deposit is adjacent to the southern margin of the late Triassic Guichon Creek batholith in south-central British Columbia. Host to the ore are sedimentary and volcanic rocks of the western calc-alkaline belt of the Upper TriassicNicola Group. In the mine area, the Nicola Group rocks are a stratigraphically complex sequence, at least 1800 feet thick, which have been subdivided into Basalt, Rhyolite, Carbonate and Clastic Sediment units. All the units strike and dip parallel to the margin of the Guichon Creek batholith and are within the batholith contact aureole. However, only the Clastic Sediment unit is in contact with the batholith.Most of the skarn and ore is within the Carbonate unit and more specifically within an Interbedded facies that consists of lime sandstone, lime siltstone, quartzo-feldspathic siltstone and argillite. The Interbedded facies and the adjacent barren Massive Limestonefacies are interpreted aspart ofa carbonate reef complex. The distribution of skarn and ore within the Interbedded facies suggests that the facies boundary was a physical and chemical barrier that resulted in concentration of metals adjacent to the Massive Limestone facies.Two stages of skarn formation have been recognized at Craigmont. In Stage I, ore-bearing magnetite-rich and actinolite-epidote-magnetite skarns developed both in basaltic rocks and in Fe-bearing siltstone and argillite of the Interbedded facies, while barren grossular garnet-epidote-calcite-pyrite skarns developed in Fe-poor rhyolitic bands within the Interbedded and Massive Limestone facies . In Stage ll, massive, barren grandite garnet skarn replaced mineralized Stage I skarns in the vicinity of diorite plugs. and specularite ore formed in brecciated Stage I skarn and clastic rocks away from the plugs. Theformation of Stage I skarns required no addition of material, only redistribution and concentration of elements already present within the Interbedded facies. However, the concentration of Cu in Stage lore requires a mechanism for more efficient leaching of Cu from the host rocks, an anomalous concentration of Cu at the site of the Stage I orebody or an additional input of Cu from an external source. The formation of Stage II skarn and ore requires only remobilization and recrystallization of Stage I skarn and ore.Copper and iron are the only elements in economic concentrations in the ore and chalcopyrite is the only significant copper-bearing mineral. Chalcopyrite is disseminated and interstitial to magnetite in Stage I mineralized skarns and is interstitial to specularite in the matrix of Stage II breccia ores. Chalcopyrite also occurs with pyrite as stringer ore in bleached • sediments and rhyolite tuffs in the stratigraphic footwall of the main orebodies.The Craigmont deposit has more features in common with Cu-Fe deposits hosted in metavolcanic and metasedimentary rocks than it has with typical skarn deposits associated with porphyry copper deposits. The orebody is more likely a product of concentration of metal contained within the Nicola Group rocks than of the mineralizing event that produced the . Highland Valley Cu-Mo porphyry deposits in the central part of the Guichon Creek batholith ."

Jan 1, 1980

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By Joël Kapusta

La pyrométallurgie du cuivre est essentiellement une chaîne de trois étapes successives d’oxydation préférentielle du fer et du soufre et des impuretés moins nobles que le cuivre qui sont contenues dans le concentré de cuivre issu de l’usine de concentration du minerai, aussi appelée concentrateur. La Figure 1 illustre la chaîne complète d’élaboration du cuivre depuis la mine jusqu’au cuivre pur. La voie hydrométallurgique traite le concentré par lixiviation, c.à.d. par dissolution en phase aqueuse à température typiquement inférieure à 100 ou 150⁰C, alors que la voie pyrométallurgique traite le concentré par fusion à température de l’ordre de 1200 à 1300⁰C.

May 2, 2024

By J. Zhang, T. Oleniuk

It is well-known that Saskatchewan has the world’s richest uranium deposits and advanced processing technologies. Unlike the Saskatchewan deposits, complicated mineralogy is common for other places in the world. Mineralogy dictates the process. Mineral Processing at the Saskatchewan Research Council has been working with the uranium industry worldwide since its inception to develop effective processing technologies to suit the unique mineralogy of each deposit. This paper reviews the research and development of uranium processing technologies in the current major uranium production areas such as Canada, as well as the potential development regions like Argentina and Sweden. Acidic and alkaline leaching processes, as well as by-product recovery technologies are discussed based on mineralogy.

Jan 1, 2020

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By R. K. Netolitzky

The Weedy Lake, Tower Lake, and Wedge Lake gold deposits illustrate contrasting styles and different ages of mineralization within the same district. The discovery of these deposits was the result of systematic exploration of gold occurrences noted during research of assessment files. The Weedy Lake and Tower Lake depo its reflect a late-stage gold mineralizing event. The e deposits developed along the same major structural break, and also display simi lar mineralogy and alteration patterns. Mineralization is developed in all the lithologies present. The Wedge Lake property, while having occurrences similar to the Weedy and Tower deposits. has the more important Twin Zone which best fits a volcanogenic exhalative model. The Twin Zone has a complex structural history without a recognizable alteration halo. The setting may be proximal to a hydrothermal vent. Mineralization is hosted within a mixed ulphide/oxide/silicate facies iron formation breccia. and the gold is intimately associated with arsenopyrite. The origin and age of the brecciation is key to understanding the mineralizing event. Traditional prospecting procedures in conjunction with conventional B-horizon soil geochemistry were instrumental in the Twin Zone and Weedy lake disco,•eries. Tower Lake was a prospecting discovery partially defined by previous drill programs. This deposit was also identified by B-horizon oil sampling.

Jan 1, 1986

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By William Petruk

Image analysis studies were performed on mill products from pilot-plant and laboratory tests that had been conducted to determine the effect of grinding media on the selective flotation of two zinc-lead-copper ores. It was found that, when the ores had been ground to the same degree of fineness with flint pebbles, ceramic pebbles or ore fragments (autogenous grinding) as with steel balls, there generally was increased sphalerite, chalcopyrite and galena liberation in the flotation feeds, depending on the textures of the minerals. The increased sphalerite liberation fully accounted for the improved zinc recoveries that were obtained when steel balls were replaced by either pebbles or ore fragments. The increased chalcopyrite and galena liberation accounted for part of the changed technical efficiency of concentration, but other factors, probably changes in oxidation and reduction of iron and in consumption of oxygen, also contributed.

Jan 1, 1977

By Saravarim A.

"The aim in flotation systems is to control the grade and recovery of the product., numerical method or sampling and analysis is used to achieve this goal. Weakness of measuring instruments, lack of process knowledge, deficiencies in management and data processing in the control of flotation cells, has led the academic and industrial units to use numerical models. In this regard, using the results obtained from the experimental design carried out in the DTP line of Gol Gohar industrial and mining complex, a regression model was developed based on the analysis of variance. To present this model, after variance analysis of factors and interactions, all models were investigated and the final model was created based on 75% of the data. The model was tested with the remaining 25% of the data to confirm the goodness of the fit. The coefficient of determination for training and testing resulted 71% and 74%. Moreover, a feed forward back propagation neural network with different layers and neuron was used to model the results. The best network structure was 6-27-1 and the coefficient of determination for this network was 99% and 98% for training and test respectively. Given the complexity of neural network models and the relatively low accuracy of the regression model, neural network has a priority assuming we have access to a specialist. In addition, the results obtained from neural network can be used as expert systems to control and optimize the flotation cells.INTRODUCTIONThe primary objective of the flotation cell control is to maintain the product's (in this case tailing) recovery and grade, which represents the index for process efficiency and product quality. Continuous estimation of these indexes requires a significant amount of maintenance, and calibration of the continuous analyzers, in order to maintain an acceptable level of accuracy. Weakness of measurement equipment, lack of process knowledge and the general deficiency in management and processing of data in the flotation cell control, will lead industrial units to use smart methods such as mathematical models, regression and neural networks in near future (Panahi, Abdollahzadeh, & Sam, 2010). Artificial neural networks are inspired by the very complex structure of human brain in which millions of nerve cells solve problems or store information by communicating with each other. The duty of neural networks learning. It should be noted that learning in artificial neural networks is limited, and what is practically considered is the computing power of the network. A neural network consists of units called neurons, and has the capacity to handle a set of input data to produce a desired output data set. Each of these input and output data sets can be assumed as a vector (Soltanmohammadi & Noparast, 2006)."

Jan 1, 2016

By A. J. Sinclair, N. Champigny

"The Cinola gold deposit in the northern Queen Charlotte Islands, British Columbia, is in a clastic sequence consisting of a lower shale of the Late Cretaceous Haida Formation and an overlying interbedded sequence of pebble conglomerate and coarse-grained sandstone of the Middle Miocene Skonun Formation. Both formations are intruded by a stock and dykes of porphyritic rhyolite. Two K-Ar model ages indicate mineralization and probably porphyritic-rhyolite intrusion at about 14 Ma (middle Miocene). A splay of the Sandspit fault system constitutes the footwall on the west of the deposit.The Cinola deposit can be classed as Carlin-type based on features such as (1) small particle size for gold, (2) Tertiary age of mineralization, (3) element abundances (e.g. high Hg), (4) dominantly argillic alteration, (5) a structural setting associated with major faults, (6) porosity of the host rock and (7) spatial and possibly genetic association with felsic intrusions. Gold is widespread and occurs mainly as grains of< 0.5 11-m in silicified sedimentary rock, and in quartz veins. Locally, coarse > 100 11-m particles of native gold occur in quartz veins, especially in strongly brecciated porphyritic-rhyolite. Ore minerals are mainly pyrite and marcasite, but include small amounts of chalcopyrite, sphalerite, galena, pyrrhotite, cinnabar, tiemannite (HgSe), rutile, magnetite, hematite and limonite in addition to native gold and electrum. No silver minerals have been found; silver was found in gold particles in amounts varying from 6.2 to 24.2 weight per cent. Alteration products are sericite, illite, kaolinite and chlorite, with abundant quartz of several stages.The host rocks, specifically the Skonun Formation, formed as an alluvial plain facies in a braided river system discharging into a marine basin in early Middle Miocene time. During the Middle Miocene, this sequence was intruded by a rhyolitic stock. The highly porous and permeable Miocene clastic sequence apparently provided an optimum setting for the development of a large geothermal system, the energy for which probably derived from the rhyolite stock. Mineral deposition followed a well-defined paragenesis, which, from oldest to youngest, is: (1) precipitation of iron sulphide minerals, and early quartz; (2) several stqges of quartz veins, with deposition of sphalerite succeeded by galena, chalcopyrite and visible gold. Micron-size gold was precipitated throughout these two stages of mineral deposition. Argillitization of the host rocks probably in part coincided with the mineralization and continued during cooling of the geothermal cell.In-situ reserves have been estimated at 41.1 million metric tons averaging 1.85 g Au/tonne using a cutoff grade of0.86 g Au/ tonne."

Jan 1, 1982

By D. N. Thurston

Luscar Stereo commenced construction of the mine at Coal Valley, Alberta, in August, 1976. It is designed to produce approximately 2.5 million clean short tons of steam coal annually - 2.0 million tons per year being committed to Ontario Hydro and 0.5 million tons per year being committed to Neptune Terminals for sale on the export market. The project involves constructing a heavy-media coal preparation plant, erecting a 42-cubic-yard dragline, constructing a shop/office complex, and developing three surface mining zones and associated facilities. As there were no existing facilities in the Coal Valley area, it was necessary to establish access roads, an airstrip, temporary utilities, fuel supplies, a construction camp, rail upgrading and communication services.

Jan 1, 1978