Search Documents

By G. R. MANSON

The Brisco Barite Mine lies 70 km south-southeast of Golden, British Columbia. Barile mineralization occurs in a northstriking brecciation zone within Ordovician-Silurian Beaver/ oot dolomites and quartzites. Brecciation was caused by faulting related to the Mount Forster-Steamboat Fault. The main barite vein occupies a fault zone and is up to 12 m wide and over 250 m long. It is light grey to white, fine grained and compact; BaSO4 content is 9/. 70 per cent. Production started in 1945 and has continued to the present. Barile originally was removed from an open pit; later, an adit, begun in 1957, reached more than 240 m along the vein, 15 m below the pit floor. Today ore is hoisted from a decline resting some 37 m below the pit floor.

Jan 1, 1984

By A. G. B. Hayes, C. L. Renzoni

"AbstractThis paper provides a rough outline of economic expectations for the near future and then goes on to discuss their effect on the expected demand for metals, using zinc, copper, nickel and aluminum as detailed examples.IntroductionMINING, as you are all painfully aware, is a cyclical business. We believe that it will remain so as long as there are economic cycles.The fortunes of the industry are tied to those sectors of the economy where decisions can be postponed until more favourable times: automobiles, housing, appliances, inventory building and capital spending. Over the past two years, while U.S. GNP fell by 3.8%, automobile production declined by 31 %, from 9.7 million units in 1973 to 6.7 million in 1975. Housing starts plummeted some 43% from 2.1 million units in 1973 to 1.2 million in 1975. Little wonder that U.S. copper consumption fell by 37% and zinc consumption by 38% over the same period.With the rest of the world's economies moving in unison with that of the United States, it is also not surprising that times have been tough for mining.Arthur Burns, chairman of the U.S. Federal Reserve, contends that each recession sows the seeds of its own recovery. The worse the recession, the better the subsequent recovery. If this is true, then the lot of the mining industry should improve significantly over the next two to three years."

Jan 1, 1977

By L. Furtenbach, T. Möller

"Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation.This paper outlines the experience from the development, installation and follow-up of liners installed in two 38' x 45' AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the “drop-zone” of the shell liners while installing the liner bolts.One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22' diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38' diameter AG mills. The results from this study are included."

Jan 1, 2012

By S. M. Grillo, M. Fiori, R. Bornioli, C. Marini, S. Fadda

The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temperature, the composition of the albitizing fuids was modified by an influx of meteoric or other waters. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1997

By R. S. James, S. P. Goff, A. E. Armitage

"Abstract - Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province."

Jan 1, 1996

By S. M. Grillo, Fiori. M., R. Bornioli, C. Marini, S. Fadda

Abstract - The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temper- ature, the composition of the albitizing fluids was modified by an influx of meteoric or other waters.

Jan 1, 1996

By T. F. Pugsley, D. Gignac

"The historical background to the project dates back to the mid-30s with the discovery of surface sulphide showings in the Cape Smith-Wakeham Bay ultramafic belt. In the mid1950s, orderly exploration commenced with an extensive work program by Asarco, INCO, Lemoine, Falconbridge and Raglan Nickel Mines Ltd. on exploration permits. In 1966, Falconbridge and Raglan Nickel Mines interests merged. Extensive exploration, drilling, under- ground delineation of the Donaldson orebody and the construction of basic infrastructure such as camps, airfield, road links from Douglas Harbour to Donaldson and Katinniq, a distance of 60 km, were completed.Production project design at that time consisted of plans for a 50 000 mt per year nickel mining and concentrating operation, including a 2000 person community and smelter at Douglas Harbour. These plans unravelled in the mid-70s due to high capital costs, poor nickel market conditions and the realization that the Raglan orebodies were not large enough to economically support the construction of green field smelter and refinery facilities for processing Raglan production. Nickel market conditions in the late 70s and early 80swere generally poor, resulting in further delays on production plans.While recognizing the very high potential to discover increased tonnages of high grade(3% Ni) in excess of 20 million tonnes, the project was deferred into the late 80s when a serious re-evaluation of exploration potential occurred and the requirement to prove up additional reserves resulted in an underground exploration program at Katinniq covering the period 1990-1992."

Jan 1, 1996

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By R. S. James, S. P. Goff, A. E. Armitage

"Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province. Copyright"

Jan 1, 1996

By David Burchell

Duckbill mining is probably the simplest method of loading coal mechanically at the face in underground mines. It is a means of reducing the amount of physical labour required to produce a ton of coal. In effect, it is merely shaker conveyor mining brought up to date with the addition of a self-loading head or 'duckbill' on the end of the conveyor line. Any mechanical device used to load coal is a means of supplanting the human muscles as the medium for getting the coal off the floor into the transportation equipment. There can be no argument with the conclusion that a man can lift so much and no more. He can load more tons of coal on a low conveyor, because the lift is less, than he can in a pit car two, three, or even four feet high. Thus it follows that, if the lifting operation is entirely eliminated, the man should be able to produce even more coal. A mechanical operation is essentially a multiplication of physical strength. Although there are various ways in which coal can be loaded at the face by mechanical means, there is, perhaps, none more adaptable than shakers equipped with duckbills. This is particularly true for thin seams and in mines having heavy, tender top conditions which require close timbering. However, as we are discussing duckbill mining, we will make no further reference to any other type of equipment. The first, and to date the only, mine in eastern Canada to adopt a system of mechanical loading at the face is the Franklin mine of the Bras d'Or Coal Company, Ltd., at Bras d'Or, N.S. An experimental Goodman shaker conveyor with a self-loading head, or duckbill, was installed in this mine in 1940. Since that time other units have been placed in operation so that, today, this mine is completely mechanized. The method of operation 1s room-and-pillar. The operation is carried on in a 42-in. seam, which lies 420 feet beneath the Sydney Main or Harbour seam in the Sydney Mines basin. The slopes bear N.25 30'E., dip 10 per cent seaward, and are about 6,000 feet in length. The physical conditions of this seam do not make it particularly adaptable for complete mechanization as it contains a large amount of foreign material, such as clay intrusions or wash-outs and iron pyrites. These clay intrusions, known locally as 'troubles', vary in thickness from a few inches to as thick as eighteen feet and usually replace the coal to the full height of the seam.

Jan 1, 1947

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966