Search Documents

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By Michael DeLallo

Clean Coal Technology (CCT) ?Technologies designed to enhance both the efficiency and the environmental acceptability of coal extraction, preparation and use?. These technologies reduce emissions, reduce wastes, and increase the amount of energy gained form each ton of coal extracted and converted into energy. ?? Carbon Capture and Sequestration are an integral part of CCT either as constructed or on a future retrofit basis.

May 1, 2008

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By Yongquan Zhu, Zhengguo Zhu, Zhichun Liu, Chao Kong, Xinqiang Gao

"The aim of the study is to have a good understanding of the change in the seepage field during and after the tunnel excavation in weathering alteration rock. Field tests are used to monitor the changes of the water table and the numerical model is used to analysis the influence of the seepage filed with different operation conditions during and after the tunnel excavation. Results indicate that the depth, diameter and pumpage of precipitation well are the main factors that have a great influence on the drainage effect. Results also indicate that different operation conditions had various effects on the decrease in water yield during tunnel construction and the recovery in groundwater level after construction.INTRODUCTIONAs a potential disease during tunnel construction, Gushing water not only affected construction schedule, increased construction cost, as well as affected tunnel stability and safety during operation, but also decreased ground-water level. What’s more, the fall of water table caused by gushing water in tunnel would have influenced surrounding residents’ living water, agricultural water and ecological environment around tunnel. In recent years, enough emphasis has been paid to the influence on environment due to the construction of tunnel as a result of the reinforcement of people’s environmental protection awareness.As a result of water collection and drainage after excavation, groundwater was discharged into the tunnel, which caused a loss of water resources in the adjacent mountain mass. Furthermore, during tunnel operation, it was difficult for groundwater level to resume its original condition, which caused a bad ecological environment, because drainage system during tunnel construction destroyed its original hydrologic dynamic balance.In order to study whether decreased groundwater level resulting from tunnel construction could be restored during operation to its original condition, this paper gave a field monitoring on tunnel displacement during construction and simultaneously, generalized model of regional hydrogeology was created according to field hydrogeology to carry out a calculation of stable seepage flow and draw comparisons between recovery conditions of various water levels."

Jan 1, 2015

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006

By Xiaoguang Zhao

The coal mining area in Northern Shaanxi, China, has been taken as the study area, and the damage mechanism of the ecological environment is discussed on the basis of analyzing the characteristics of natural eco-environment and resource development in this area. Mining subsidence is taken as an example, and by using the Gray Correlation Analysis method, the key impact factors have been selected. An assessment model with fuzzy comprehensive evaluation has been constructed, and 12 coal mines have been quantitatively assessed. This paper also constructs an ecosystem health assessment method and index system in the coal mine area on the basis of ecosystem health theory, and assesses the ecosystem health status in the Shenfu coal mining area from 2000?2006. The research results are expected to help the eco-environment protection process in the designated coal mining area.

Aug 1, 2013

By Stefan Boshkov

THE ADVENT of mining at great depth has brought to the fore the question of stresses around mine openings. The many-pronged attack on this problem is certified by the accelerated appearance, in the mining literature, of articles on various topics related to this subject (1). Whereas it may be agreed that we, of the mining profession, have fallen woefully behind in research and the development of an understanding of this important facet of the general problem of mining, it must also be accepted that the analysis of the stresses in a mine structure is usually more complex than is the case in the majority of structures encountered and dealt with in civil engineering. Whereas homogeneity and isotropy are readily acceptable for most metals, such properties are but crudely approximated in rocks. Whereas the external loads on a structure in civil engineering may be readily determined, those on a mining structure are subject to ?conjecture. Whereas the limits of the structure may readily be defined in civil engineering, the boundaries of the mining structure are, in most cases, indeterminate, and subject to intelligent guesswork, at best.

Jan 1, 1956

By Doug Milne

Linking Classification Systems with each other Similar Parameters between systems Different Rock Mass Properties Rock Mass Classification parameters and geology Different sources of data Commonly Used Rock Mass Classification Systems Q? = Q with SRF = 1.0 RMR? = RMR with no joint orientation correction RMR76 = 9lnQ + 44 RMR?76 = 9lnQ? + 44 RMR76 = RMR89-5 RMR?76 = GSI = RMR89-5 MRMR = ??MRMR

May 1, 2013

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By F. Sorensen

ABSTRACT Electricity production by the Electricity Supply Commission of South Africa (Eskom) is the most important beneficiation process for South African coal. As one of the world’s lowest cost producers, energy-intensive industries such as ferroalloys and aluminium were introduced. However the poor were neglected. The white paper on energy policy (Department of Minerals and Energy, 1998) sought to redress this. Also, chasing economic growth to generate jobs resulted in high electricity demand and interruptions. Lifespan estimates of South African coal reserves based upon peak theory vary widely. Approaching peak, coal production in the future will be more expensive and, thus, contribute to more expensive electricity, which could inhibit industrial development unless South Africans work smarter.

Jan 1, 2011

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012