Search Documents

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By John Stoten

"The 1980s have proven extremely difficult years for many resource-based organizations. Mining companies have learned how to weather the negative effects of inevitable economic cycles. However, with some notable exceptions, such as gold mining companies, the mining industry has faced a broader and deeper round of cutbacks than any experienced since the 1930s. Downsizing has been a major issue for many mining companies as they have faced the need for dramatic staffing cost reductions in the recent past.The continuing current rapid rate of change in technology and the marketplace, coupled with increasing merger and acquisition activity, will provide an on-going need for some companies to face major reorganization. This inevitably will involve down-sizing activity in some instances.Given this scenario, it is worth reviewing the industry's past experiences to identify approaches and techniques that could prove of value in handling a future staff downsizing challenge. This paper is based upon a downsizing consultant's experiences with the mining industry and other sectors, and highlights what appear to be key staff reduction planning and process issues.Planning for DownsizingA review of companies' downsizing activities of the last few years reveals four key activity stages which need to be addressed to ensure a successful transition. These stages are:1. organization planning;2. developing cost reduction strategies;3. implementing downsizing; and4. building for the future.A business situation that is severe enough to require drastic staff cuts typically affects all aspects of a company's operations. Most mining companies have reviewed cost efficiencies in many operational areas. However, these reviews often have been short term in focus . As a result, some companies have experienced multiple downsizing; each event a response to an immediate economic threat. This has sometimes resulted in an unstable organizational environment, with severe stresses on staff morale and productivity.In the long term it is more efficient and less stressful to the organization to adopt a more comprehensive and longer-term strategy. Especially in capital intensive mining operations, it makes sense to review all areas of business activity, not just staffing."

Jan 1, 1989

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012

By G. L. Palmer

"Abstract- ln 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with garnet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess mineability and to provide material for metallurgical testing in a pilot plant located at the site. Ilmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay . Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By T. M. Ruff

A GPS-based traffic awareness and collision avoidance system has been implemented at mines with long, narrow access roads to help avoid accidents involving two approaching vehicles or vehicles following too close. A simple display in the cab of each outfitted vehicle gives an indication of oncoming traffic and a voice announcement indicates the type of vehicle that is coming as far out as 300 meters. Advanced warning of approaching vehicles is increasing driver awareness, especially around blind corners and in adverse weather such as heavy fog, snow, or rain. Speeding alarms have also been implemented and are especially critical as a vehicle approaches reduced speed areas near single-lane bridges or tight curves. A description of the system, safety improvements seen since its introduction, and implementation challenges will be discussed.

Aug 1, 2013

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By T. H. Janes

THE POSSIBILITY of producing pig iron from iron ores of British Columbia for a west coast primary iron and steel industry has been investigated by the provincial government and by commercial interests on sever.al -occasions. The latest study is that currently under way by The Consolidated Mining and Smelting Company of Canada, Limited. The Company is studying the possibility of making pig iron from the oxide calcine resulting from the roasting of pyrrhotite. tailings used in making sulphuric acid for fertilizer production at Kimberley. A comprehensive report on the subject .of establishing a primary iron and steel works in the Province, based on local iron ores, was prepared by Arthur G. Mc-Kee and Company of Cleveland, Ohio, in 1942 for the B.C. Minister of Mines and is available to interested parties. A detailed survey on the subject was also pre-pared in 1954 by Dr. G. P. Con-tractor, then .of the British Columbia Research Council. Considerable information is there-fore available on most aspects of an integrated primary iron and steel industry in British Columbia to supply the needs of the western provinces. To date, however, no basic iron industry has been established despite the .occurrence of high-grade iron ore deposits on the offshore islands and the high freight charges on iron and steel products brought into the area from Eastern Canada and overseas producers. The chief deterrent has always been the relatively small and highly diversified market available to a local steel producer. Other major fact-ors have been the lack of sufficient proven reserves of iron ore, and the difficulty of making pig iron, suit-able for steel manufacture, economically on a small scale. Technical and economic conditions have changed considerably since World War II and the establishment of a primary industry based on electric furnace production of pig iron or on one of the direct reduction processes, coupled with electric furnace steel production, may now be economically feasible.

Jan 1, 1958

By R. Lapcevic, P. Lokin

"Among other components, ore body „T“ was discovered in the Bor pit copper mine at a depth of app. 500m. The ore body is relatively small: 60-65m long, 40-45m wide and up to 50m high, but with an extremely high content of copper and accompanying metals. The rock mass containing the ore body is composed of altered andesite of relatively poor physical-mechanical characteristics. The exploitation of this ore body by way of conventional mining methods was associated with high risk, cost, and potential losses of the rich ore. Due to everything specified hereinbefore, the adopted solution involved ore exploitation with complete ensuring of excavation stability, thus forming an extremely large underground opening. The excavation and supporting were performed according to the NATM principles along with applying shotcrete, 9-25 m long cables, and horizontal and vertical lattice girders. The excavation of the ore body was completed in app. 2.5 years, all the while ensuring complete stability and security of people and equipment; construction works were constantly monitored. The proposed solution for ore excavation enabled more than 95% exploitation of ore as requested by the Investor, while depletion due to waste-rock excavation was less than the allowed 5%. INTRODUCTIONThe Bor copper deposit is located in Eastern Serbia. Copper exploitation in Bor commenced as far back as 1902. A total of 26 ore bodies varying in size and valuable mineral content have been excavated so far. One of the most recent excavated ore bodies is ore body „T“, which is one of the smallest bodies by volume, but also a body with one of the largest content of copper and accompanying metals. An important fact regarding its exploitation is that it is located at a depth of app. 500 m; that its shape is irregular: 60-65 m long; 40-45 m wide and app. 50 m high; and that it lays within a rock mass of relatively poor physical-mechanical characteristics. In addition, above it, in its immediate vicinity, ore body „F“ was previously excavated and its room was refilled with backfill and water. Excavation methods common in mining practice (excavation with caving, excavation with backfilling, excavation with protective pillars) were inadequate in this case for various reasons:• The immediate vicinity of the previous ore body „F“ room could cause expansion of the caving zone also to that room, along with penetration of groundwater and flotation sludge;• Possibility of deformation expansion caused by caving as far up as the surface of the terrain, including the urban area;• Difficulties in maintaining the stability of excavation sidewalls having steep slopes and great height;• Significant loss of ore mass with a relatively high content of metals etc."

Jan 1, 2015

By Askari-Nasab, D. Checkel, K. Awuah-Offei

Life Cycle Assessment (LCA) is an emerging environmental management tool for examining environmental impacts from cradle to grave. In this paper, LCA is used to evaluate the acidification potential (AP) and global warming potential (GWP) of belt conveyors and truck haulage systems in a surface gold mine using the ISO 14040 standards. The results show that, for AP, the truck system has 32 kg of equivalent SO2 per functional unit, compared to 8 kg for the conveyor system. However, for GWP, the conveyor has 2,820 kg of equivalent CO2 per functional unit, compared to 648 kg for the truck option.

Jan 1, 2009

By D. W. McDonald, N. A. Duke, R. L. Hauser

"Abstract- The NERCO Con Mine is situated in the amphibolite facies aureole of the Western Plutonic Complex overprinting the Yellowknife Greenstone Belt. Metamorphic grade of the upright monoclinal basaltic succession decreases from hornblende-amphibolite facies along the border of the batholith to greenschist facies. Metamorphic isograds, subparalleling the faulted margin of the batholith, transect volcanic stratigraphy and coincide with major gold­ bearing shears.Gold mineralization is confined to north-striking, west-dipping shear zones where hanging­ wall amphibolite facies mineral assemblages retrogress to chlorite-carbonate-sericite-sulfide bearing schists hosting multiple generations of quartz-ankerite veins. The gold-producing portions of the Con and Campbell Shears occur where these structures transect an east trending thermal corridor. The corridor is defined by granitic plugs and a number of related breccia bodies, that can be traced outwards from the batholith across the greenstone belt.Prograde reactions of greenstone during amphibolitization effectively liberate fluids that partition metals. With retrograde reactions at shear zones, gold is precipitated with quartz due to the destabilization of sulfide and arsenic complexes. The coupling of regional prograde metamorphic and restricted retrograde metasomatic overprints suggest mineralization is temporally related to emplacement of the Western Plutonic Complex. Economic gold concentrations within the intrusive corridor indicates enhanced metamorphic overprint of hornfelsed greenstones enveloping satellite intru sives peripheral to the main batholith."

Jan 1, 1993

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By Donald E. Wakefeld

"The pace at which mining will occur in Northern regions and Arctic lands will depend on the answers to a number of questions. Who are the local aboriginal participants? What land uses are they pursuing? What are their objectives? What is their understanding of the process of mining development? This paper will focus on the last question, communicating the process of mineral development to local aboriginal communities.IntroductionIn the environmental impact hearings for the BHP-DiaMet diamond mine, the smaller Dene Treaty 8 Nation argued for the settlement of its Land Claims as a pre-condition to development. However, the larger Dene Treaty 11 Nation were prepared to permit the mine to proceed on the basis that their people would receive benefits during the construction and operation of the mine.Wherever mining is the significant basis for tax revenues and economic development expectations may be encouraged beyond the realities of the situation. Izok Lake has been known for several decades as a significant mineral deposit but because of its size and the transportation costs involved, it is now a “frozen” ore body. The extent of its mineralization at current metal prices will not support the mining and processing costs without substantial government support for infrastructure and roads. At the opposite side of Canada, Voisey’s Bay clearly satisfies all technical criteria but, nonetheless, two Inuit groups, the Innu, and Métis, have all made LandClaims relating to the mine area.Contrasting the mineral deposits at Voisey’s Bay and Izok Lake emphasizes that the timing of production is dependent on factors such as the grade and amount of reserves, their market price, location and availability of government support. Nonetheless, it is this author’s thesis that given an economic orebody the next most important factor is good communications. It is his view that Arctic mineral development will occur quickly only where good communication has resulted in the trust and mutual respect necessary to implement the mammoth cultural changes required."

Jan 1, 1996

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By P. D. R. Maltby

"The Canadian Institute of Mining and Metallurgy has undertaken to host the XIV International Mineral Processing Congress to be held in Toronto at the Royal York Hotel from October 10 to 16, 1982. The theme of the Congress will be ""Worldwide Industrial Application of Mineral Processing Technology."" The program will include 10 sessions and numerous field trips to the different mining areas of Canada.For prospective authors, the preliminary program includes sessions on,1. Flotation - plant practice, equipment design, simulation, control and economics.2. Comminution - plant practice, equipment, design, simulation, control, wear, energy consideration and economics.3. Round table seminar on large grinding mills.4. Round table seminar on modern and future plant design.5. Mineral processes to recover precious metals.6. Mineral processes to recover energy minerals (coal, uranium).7. Mineral processes to recover industrial minerals.8. Round table seminar on the environment and ecology and how the different countries cope with associated problems.9. Materials handling with an emphasis on agglomeration techniques ereconentration methods, solid-liquid separation.10. Open session to deal with topic emerging from general demand."

Jan 1, 1980