Search Documents

By Sijing Cai, Chengpu Zhou

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

Natural gas is a comparatively new fuel in Australia. It was first used in small quantities in Queensland in 1965, but it was not until 1969 that natural gas reached the capital cities Brisbane, Melbourne, and Adelaide in that order; then in 1971 it reached Perth. By the mid seventies, natural gas had secured a significant proportion of the energy markets in Queensland, Victoria, South Australia and Western Australia and in 1976 supply commenced in Sydney. In that year - 1976 - gas supplied about 12.5% of the total demand for primary energy in Australia excluding transport. In the current financial year - 1981/82 - natural gas is expected to supply nearly 19% of the market and forecasts for 1990 range up to 25%. From a starting point in the late 1960's when manufactured gas supplied a small but important proportion of the non-transport energy market - less than 3% - we have exper- ienced an average growth of nearly 24% per annum up to the present time.

Jan 1, 1982

By Tyler MA

If the record of maj or proj ects in Australia is taken into account, it is apparent, the proper planning of an industrial relations strategy for many such projects has been ill considered by project developers. The recognition of the need to develop a plan from the initial feasibility study has been forced on those promoting new projects by the publicity given to the Australian industrial relations record. The delays in delivery caused by factors supposedly out of the project's control are often given for non-performance of contract and used as an excuse for limiting further development. Many of the problems experienced in project development can be overcome with sound industrial relations planning. The promises given in the euphoria of the early stages of a project relating to price and delivery often become a burden for the future because the complexities of the Australian Industrial Relations Systems are not understood or considered. The recognition by senior executives of their responsibilities in this area will contribute greatly to a new era of project development.

Jan 1, 1983

The technological advancement in computing power and the increasing demand for information processing systems spread throughout many aspects of a corporation's business activities has revolutionised management information systems departments. This revolution is manifest in the proliferation of mini-computers and micro-processors as well as the planned or unplanned migration from centralised processing to distributed processing. The total data processing investment in people, hardware, software and telecommunications has reached a high level in many organisations. Therefore, the cost of inadequate planning or ad hoc growth of systems can be considerable. The concept of MIS systems planning has gained adherence in recent years; however, there appears to be a wide diversity in the effectiveness and quality of corporate systems plans. To be effective a systems plan must have the support and concurrence of executive management of an organisation. A disciplined planning approach to systems together ,with the involvement of senior user management as well as MIS management is necessary to develop a satisfactory systems plan that forms the basis of a corporation's data processing strategy.

Jan 1, 1980

By R Espinosa-G=mez

Industrias Pe±oles, S A de C V (Pe±oles) in Mexico, is a major silver producer. The Pe±oles mining division has eight operations and the flotation process in seven of them to concentrate the metal and mineral values. Common metal and mineral values are: metallic gold and silver; gold-silver alloy (electrum); silver sulfide minerals (acanthite, pyrargyrite, freibergite, proustite); lead sulfide (galena); zinc sulfide (sphalerite); and copper sulfides (chalcopyrite and bornite). This paper aims to share Pe±olesÆs mineralogical and metallurgical information on the seven operations where the flotation process is used. Some basic conclusions are drawn from this analysis. Some of the information presented includes: types of orebodies, concentration processes, concentrator throughputs, head grades, concentrate grades and recoveries. Importantly, grind size and liberation values for the main mineral species are presented along with the relationships between sphalerite liberation and its recovery, and galena liberation and its recovery. Also included are three mineralogical case studies: maximisation of silver recovery at the Fresnillo mine producing a silver-zinc concentrate; options to improve gold recovery at the Tizapa mine; and sphalerite iron content for the different orebodies.

Jan 1, 2005

By D Millette, F Gay

Surface tailings are finely ground waste materials produced in all mines after the mineral or metal has been removed from the metallurgical process. Current methods for disposal of tailings involve constructing dams, dumping into existing waterways, and depositing as backfill underground. Each method has its drawbacks in terms of cost, level of complexity, safety and environmental concerns. Backfilling is the process whereby waste material (generally metallurgical tailings, prepared aggregates or a combination) is placed from the surface back underground into open mine workings via conveyor belts, hydraulic or pneumatic pipes or gravity. In the backfill process common difficulties are expensive placement costs, equipment wear and the ability to meet early and long-term strength requirements. Traditional tailings transportation in pipes involves the use of water as the transport medium. Foam technology involves the introduction of micro-air bubbles that replace the water as the main transport medium. This air can be removed after placement if necessary, by the addition of a defoaming agent. This could produce an under-saturated stable cake. Foam technology has the potential to revolutionise surface tailings disposal and backfilling by providing a less expensive and environmentally safe alternative to those just described.

Jan 1, 2000

By J-M Rendu

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which includes the requirement that a Competent Person prepare and approve publication of mineral resources and reserves. Most national regulatory organisations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organisations, and many dedicated individuals. The historical development of these standards is summarised in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of an International Code are outlined.

Jan 1, 2002

There is a link between the requirements of society and the determination of curricula in tertiary educational institutions. Mineral resources exploration provides a strong example of this link. The resources exploration business engages in scientific, engineering, commercial and management activities in an endeavour to discover economically extractable commodities. Most geoscience and geotechnical graduates are employed by the mineral industry for resource exploration and development. This industry comprises a wide range of employer groups which include the Bureau of Mineral Resources, CSIRO, energy authorities, State geological surveys, State water commissions and private companies. Such employers are variously charged with the task of understanding and utilising earth resources to the benefit of society. It follows therefore, that undergraduate education and post-graduate specialization should be directed towards meeting the needs of employer groups in the geoscientific and geotechnical fields. In the past the training of most Australian geologists has emphasised classical science. This type of training remains of primary importance in the early undergraduate years but there is a need for modern educators to recognise the increased desirability for the inclusion of geotechnical subjects in the curriculum. Modern geo-education should address four main sectors when deciding curricula:

Jan 1, 1986

The cement industry requires large quan- tities of limestone, its main raw material. It is the major consumer of this mineral. Limestone is widely distributed throughout Australia but location in relation to major markets, and transport considerations render most deposits of no economic value. Of those which are sufficiently close to the major me- tropolitan markets many are rejected as being unsuitable on grounds of quality, inadequate size for major development, or other reasons such as environmental considerations. Detailed geological investigations are necessary, not only to prove raw material sources prior to establishment of a cement works but also to permit planned extraction programmes and satisfactory grade control during subsequent development. Conventional field techniques have generally proved adequate for raw material exploration. Data assessment and reserves estimation also are by conventional methods although the specific requirements of the industry relating to raw material and cement quality, the type of manufacturing process and fuel used are relevant. A number of case studies from different geological environ- ments are examined and comparisons made bet- ween the predictions of the exploration stage and subsequent experience in quarrying prac- Tice.

Jan 1, 1979

In an industry that is data-hungry and increasingly international in its outlook, the role of the New Zealand Government in facilitating exploration and mining activity here presents unique challenges. All things being equal, the Regime itself should result in æefficient outcomesÆ, however central to this rational economic tenet are the assumptions that the regime is in keeping with the times, other legislation works in tandem with it, and that those who administer the regime have the knowledge and experience to apply the rules wisely. Following the Crown Minerals review in late 2003, a shift in emphasis from Crown Minerals æmanaging the ActÆ towards proactively æmanaging the mineral estateÆ for greater benefit for all New Zealanders means that these assumptions are being increasingly challenged and addressed through a variety of initiatives. These include improved access to relevant data sets, minimisation of red tape and compliance costs, increasing emphasis on permit holder compliance with work programme obligations, changes to the Minerals Programme and regulations, closer collaboration with and representation to other government departments and councils, and additional recruitment of industry-experienced staff. This presentation will highlight aspects of these initiatives, and examine how they will collectively contribute to facilitating future exploration and mining activity in New Zealand.

Jan 1, 2004

By Brady B. H

Increasingly, consideration is being given to the nominal `outcomes' of degree courses in engineering, including mining engineering. These are concerned not only with knowledge and technical understanding but also with capabilities in the professional application of engineering principles to problem solving, multi-disciplinary teamwork, communication and life-long learning. This paper discusses concepts of education, professional formation and training and the associated development of competencies in applying knowledge, understanding and technical insights and skills to new situations. In developing guidelines on preferred attributes and competencies in graduate mining engineers, a survey was conducted of a range of industry personnel involved in selecting graduate mining engineers. The results not only clarified the spectrum of competencies sought but also provided valuable detailed views to assist in defining a mining engineering curriculum. Considering a greater concern with the development of more `well-rounded' graduates, the implications are discussed with regard to teaching and assessment activities and the time demands on academic staff when a `coaching' role is emphasised. In line with international and Australian moves in engineering education, notions on education of mining engineering graduates in Australia are under review. The results will provide continuing challenges to all involved.

Jan 1, 1997

Renison Goldfields is one of Australia's largest mining companies with annual sales revenue over $600 million. It has ten operating mines and processing plants, with operations in most States of Australia and in Papua New Guinea, Indonesia and the United States. The exploration division is active in,other parts of the world, including Europe and South America. RGC produces gold, copper, tin, coal and mineral sands. RGC is typical of companies in the mining industry in that by contrast to the typical pattern in other industries, it is necessary to have systems to handle a variety of different types of operations, a range of size of operations, and operations in remote locations.

Jan 1, 1995

The rare earths market is relatively small and slow growing. Three applications using mainly cerics rare earths : catalysts, glass-ceramics and metallurgy are volume market. Inside this slow moving frame, fast growing niches can be found lamp phosphors, permanent magnets, fine cera- mics... There is no specific ore for one given element, and the natural occurence of any ele- ment is almost constant in both monazite and basnaesite. This creates the "balance problem" that consists in the best compromise between shortage and over production. The general trend of prices is downward in constant money. Despite this difficult environment (price decrease, technology changes, etc...) lots of company have always been attrac- ted by the rare earth business.

Jan 1, 1986

The purpose of this paper is to provide a ælook behindÆ the Coal Mine Health and Safety Act 2002. The more important policy considerations in the development of the Act are described along with a summary of the main provisions of the Act. The Act, together with supporting regulations and other instruments will formalise the use of risk management as a necessary discipline in the systematic management of occupational health and safety. It must be recognised that the purpose of this paper is not to provide a legal interpretation of the legislation nor is it to provide legal advice. Rather, the main purpose is to provide some indication of the underlying intent behind the Act.

Jan 1, 2003

By E Villaescusa

This paper summarises research work carried out at the Western Australian School of Mines on mine backfill properties in the last few years. The fill properties presented relate to cemented aggregate fill and cemented tailings fill. Emphasis of these studies has been placed on the composition of backfill materials including aggregate particle size distribution, cement dosage and influence of cement admixtures. The unique features of the backfill research carried out at WASM during the last few years are the accomplishment of a study into the properties of large cemented rockfill samples by triaxial testing and the investigation of the properties of fill material made from highly saline ground water prevailing in the Goldfields region of Western Australia. Exploring different cost-effective binding agents for mine backfill was also carried out at WASM. Special effort has been put on the development of fill materials compatible with hydraulic and paste fills. During the process, specific methods and procedures for laboratory testing of backfill material have been formalised. The on-going backfill research on sample scaling is summarised and the future direction of WASMÆs backfill research focus is outlined.

Jan 1, 2000

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

By I Ross

The ground handling system needed for the second lift of the underground block caving operation at Northparkes Mines had to link into the existing infrastructure. Production requirements indicated that an annual output of 5 Mtpa was necessary from a depth of approximately 850 m. The shaft that serviced the first lift stopped at a depth of 520 m. This paper covers the selection of the design for the system and the factors that were taken into consideration in making the decision. It will describe the installation program and methodology and highlight areas of significance and then detail some of the issues concerning commissioning of the ground handling system.

Jan 1, 2005

By P Dight

Increasing the strength of backfill has been the subject of much research. In the former Soviet Union most methods concentrated on the fill mixture including chemical additives, binder re-grinding, water electromagnetic activation and the use of vibration and turbulent activation. For the most part, this research has been confined to the laboratory where the results were not representative of field conditions. These methods also were directed at increasing the mass strength and were not specifically aimed at strengthening the fill where it may subsequently be exposed for instance on the side or underneath as it required for underhand cut and fill methods of mining. In the Republic of Armenia, a method of fill strengthening known as electro-activation has been adopted. The deposit it an epithermal gold deposit which to-date has been mined using underhand cut and fill with timber support. The backfill comprises cement and pumice placed in 2.5 m lifts. Central to the method of electro-activation is the placement of the electrodes in the stope in which the polarity and the electrical potential are changing during filling. The process promotes the binding of the fill layers, the bond to the side walls and to the adjacent fill. There is a significant increase in the compressive and tensile strength. The process has been used with beneficial effects on reinforced concrete and could be used in any mine utilising hardening fills.

Jan 1, 1998

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000