Search Documents

Shizuyuan deposit is a compound type of greisen and skarn associated' with W,mo,Sn,and BI mineralization. Tungsten-bearing skarns are located at the contacts between carbonate rocks and granitic stock. Ore-bearing greisens occur in the top of granite or superimpose on the skarn rocks. Although mineralization and alteration are heterogeneous,there are clear patterns in the preferred associations of minerals on all scales, and an orderly sequence can be distinguished. The sequence of mineralization Isom bhar. Gsesus-.contactròoctaard is characterized bòyVtia of L, a4[~!kient assemblages W(mo,~P),,,W,(,Mo,Sn,Bi),Sn (Bi), and Sn. Skarn formation is divided into an early sk.arnoid stage and a late metasomatic stage. The skarnoid stage formed grandite garnet and diopside pyroxene in the limestone. The iron content of garnets decreases significantly away from the granite, whereas pyroxenes maintain a relatively constant diopsitic composition. The metasomatic skarn stage is charac- terized by hydrous silicates. The mineral assemblages of. greisens are regularly distributed in space. The feldspar-quartz-fluoride was usually formed in-the deeper part, upwards giving way to muscovite-quartz, and topaz usually occurs in the uppermost part. The distribution, and miner- alogical relationships of alteration facies suggest that they formed as a result of the progressive reaction of an ascending hydrothermal solution with aluminum-nearing limestones an-d granitic rocks respectively. The ore elements were mobilized and deposited in association. with hydrosilicate alteration of skarns and greisens.

Jan 1, 1987

A review of publicly available coronial inquiries into fatalities that have occurred within the resources sector since the year 2000 reveals that a loss of corporate memory has been a contributing factor in 40 per cent of these accidents (National Coroners Information Service, 2010, Appendix B). With the highest levels of employee turnover within the Australian economy, increasingly complex operations and an ageing workforce, the management of corporate memory within the Australian resources industry poses a significant and often unrecognised safety risk.    The North Parks airblast of 1999 is used as a case study to highlight how corporate memory loss poses a significant hazard to resources projects and how such incidents will continue to occur if corporate memory is not effectively managed. Best practice from other industries is discussed to demonstrate how knowledge management systems can effectively work. This paper discusses how systems can be put in place within the geographically diverse resources sector, and how at the heart of any knowledge management system a culture of knowledge management needs to exist within an organisation.   The paper then discusses the importance of retaining key personnel and utilises findings from primary survey data collated in 2009 to show the size of the retention problem within the industry. From the data possible solutions to retaining key staff are proposed.   Finally the large and increasing role of contractors and consultants within the industry is discussed and methods of managing their knowledge are proposed.

Jun 1, 2010

Mine Dewatering for reoccupation of a flooded mine requires rehabilitation and recommissioning of shaft and sane level functions to provide safe efficient access, services and logistics, as well as securing connections with all exposed workings. The objective is the earliest secure reoccupation of the target depth horizon for minimum water pumping, consistent with an appropriate investment and optimum schedule of operating inputs to the dewatering, redevelopment, services and consolidation processes. Strategy must focus on recommissioning of relevant functions in the shaft and at stage pumping horizons, advance of logistics close to pumping and rehabilitation, management of the secured exposed workings. The progress must be systematic, sustained and integrated, and must be secured against risk and uncertainty. There must be a strategic capability to respond effectively, and manage interruptions to processes, conditions requiring higher or different resources, and contingencies which affect schedule, budget or risk profile for the continuing programme. Planning must aim to reduce or contain risk or uncertainty elements and contingencies, limit interruption frequency and severity, identify and provide the capability for efficient responses. It is appropriate to model and simulate the reoccupation analogous to a mine initial development production programme. Only minor changes to relationships and relativities of models for Capital works, Operations (Production and Development) and Services/Logistics are needed but the model for management of workings is more relevant than that for depleted workings in an operating mine because of the water and other transfers. An important difference is the unsteady state of operations which requires probabilistic modelling of availability and utilization of equipment and processes.

Jan 1, 1988

The proponents of new mining projects always run the risk that their project is deemed to be not in the public interest. Nothing to be done here except to try and pick it earlyùit is, after all, the approvals process that is supposed to screen such projects out. But there is a second risk, about which much can be done: that inadequate or untimely information confuses the formal assessment of a project and the political context within which the decision is ultimately made. This is environmental impact assessment (EIA) process risk and it has become steadily greater in a changing world, where: miners have lost clout; public trust in institutions has declined; governments follow, as authority pyramids give way to spheres of influence; NGOs are asking the questions people want answered; and stakeholders have become the reference point. This new world deals harshly with yesterdayÆs methods. But it needs to be understood if principles and methods for managing EIA Process Risk are to be advanced.

Jan 1, 2003

By R D. Morrison

This paper reviews the need for, and potential of, dry technologies in mineral processing, and considers the problems that will have to be solved for such technologies to be economic. The need for water in conventional mineral processing is reviewed, together with the advantages and disadvantages of operating wet and dry. A wide range of dry processing techniques have been developed in the past, some of which are in routine use either in mineral processing or in allied industries. However more information is needed to determine which of these is appropriate to replace conventional wet processing. It is concluded that a new paradigm is required for the design of processing flow sheets, which will need to extend to innovative ways of valuing particular process routes. Research is also required to develop current dry methods to increase throughput and overcome other disadvantages, and to develop new or refined dry separation methods, perhaps exploiting alternative mineral properties.

Jan 1, 2003

By G C. Lukey, J S. J van Deventer

The disposal and subsequent encapsulation of mine tailings in a cost-effective and environmentally secure and responsible manner is one of the principal issues facing any modern mining project. A careful assessment of all options available for the capping and subsequent remediation of tailings is important because it can result in large capital, operating and closure cost-savings. For these reasons, the technology of geopolymerisation is receiving increasing attention for the stabilisation and solidification of waste materials produced from mining operations. The first part of the current study investigates the application of geopolymer technology to the capping of hypersaline mine tailings. It has been found that suitable geopolymeric materials which have satisfactory compressive strength, durability as well as low permeability, can be formed using between 60 - 75 per cent of mine tailings as the main ingredient. It has been established that geopolymeric materials have the ability to suppress dust generation and prevent salt precipitation on the surface of the mine tailings. The slurry-like consistency of geopolymers would promote efficient application procedures through established tailings disposal techniques. This is a possible close-out technique for hypersaline tailings storage facilities such as those commonly found in Western Australia, which meets both regulatory requirements and community expectations. The immobilisation of contaminant metals within geopolymers has been investigated in the second part of the present study. In particular, the leaching characteristics of Cu and Pb from geopolymeric matrices derived from different fly ash sources have been examined. Potential breakdown of each geopolymer containing metal contaminants due to the leaching of Si and Al from the geopolymeric matrix has also been investigated.

Jan 1, 2000

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By J J. Cilliers, E Ventura-Medina

Mineral froth flotation is used to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. As air is blown into the slurry, the hydrophobic particles attach to the air bubbles, while the waste particles remain in suspension. While the froth rises up, bubbles start to coalesce and burst, allowing the entrained liquid surrounding the bubbles to drain and return part of the gangue to the pulp. Mineral separation is therefore a function of the amount of valuable material loaded on the bubble shells, as well as the amount of gangue material entrained in the liquid channels separating the bubbles (Plateau borders). As a result, the separation performance of the process is affected by mineral attachment and drainage or bursting in the froth. This study aims to establish the relationship between solids loading, froth stability and separation performance. For this purpose, a series of industrial experiments were carried out to measure mineral attachment as well as bubble bursting by combining direct sampling of the bubble films and video image analysis of the froth surface. This work suggests that the solids loading on bubbles strongly affects the separation performance. The results generally showed that solids loading and concentrate grade are closely related, while froth bursting rate can be linked to the drainage of gangue from the Plateau borders and also to the overall recovery of valuable mineral. It was shown in particular that higher loadings, usually associated with higher froth bursting rates, are indicative of more selectivity in attachment and therefore a higher mineral grade in the concentrate. Additionally, this work suggests that bubble solids loading and froth stability are essential parameters to include in froth flotation models as they allow control and optimisation of the flotation performance.

Jan 1, 2005

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By Leigh G, Gottleb G, Wilkie G

The estimation of particle liberation is important in the study of mineral concentration. With simple systems, where the densities of the components are low, the liberation can be studied directly by density fractionation. For most practical systems, and particularly for the dense, complex sulphides, the only method known is by measurement in polished section. There are two major difficulties with such measurements. Firstly, the measurements themselves are difficult and considerable care is needed before reproducible results can be achieved. Secondly, a well known stereological problem arises which gives the estimates an inherent bias. The paper discusses both aspects of the problem. The practical features of measurement are treated in detail and a method described which has been developed and proven to give reproducible estimates of the liberation in the section. This discussion relates to automated measurements by QEM*SEM and presents a way of estimating the confidence limits within which measurements lie. Comparisons are shown between measurements made by the traditional manual optical technique and automated equipment. Stereological reconstruction is also discussed briefly. Several methods have been presented in the literature but all are complex and none is yet widely accepted. Area measurements are less biased than linear estimates so a practical approach is to use area measurements in uncorrected form. The topic is still being actively researched so it is expected that one method will soon emerge as the standard technique.

Jan 1, 1993

The Telfer Gold Mine, owned and operated by Newcrest Mining and located in Western Australia, is currently being expanded. A new underground sublevel cave development is proposed along with an appreciable expansion of the open pit. The Telfer area is generally subject to low rainfall, however, during the wet season cyclonic events can result in sizable rain events, which have the potential to cause substantial inflow. In addition to this, during the first five years (nominal) of the mineÆs life, there is the potential for drainage paths between the pit and the underground mine via decommissioned underground workings which lie directly under the pit. After this initial five year period the pit floor will be mined out below the old workings and will therefore no longer connect to the underground, however cave breakthrough to the surface may start to occur thus providing another water path into the underground mine. To arrive at an optimum, safe solution for dewatering the mine that successfully addressed the above items, a rigorous risk analysis was included as an integral part of the design process. This involved the determination of the probability of events occurring and the consequences of these occurrences. This was compared against the cost of mitigation for the various events. This paper outlines the process by which a safe concept addressing all the issues relating to dewatering the proposed mine has been arrived at. This process included: Establishing the pit catchment areas. These were based on historical run-off data and took into account practical mitigation works. Establishing an Average Recurrence Interval (ARI) based on reference material and historical rainfall data. Utilising a standard approach based on Australian Rainfall and Run-off (ARR) to calculate pumping and storage requirements for the various catchments. Analysing the 20 years of recorded rainfall in the Telfer area to establish the duration, magnitude and sequence of events. This analysis assisted in determining the surface run-off coefficient. Establishing potential water storage areas and determining the risks associated with using particular storage options. Establishing the percolation rate through the cave zone. A degree of uncertainty regarding the percolation rate in the cave zone required that the consequences of using various percolation rates were considered to aid in establishing the rate which was adopted. Establishing preliminary concepts and determining the most economically viable concept. Conducting a risk assessment based on the principles outlined by Australian Rainfall and Run-off (ARR) to confirm that the appropriate Average Recurrence Interval (ARI) had been selected. A risk assessment was also conducted in accordance with client requirements. Establishing the optimum pump station sizes and storage capacities. Establishing the appropriate numbers of duty and standby equipment. By using the foregoing process, which included a number of stages of risk analyses, an optimum dewatering system concept was produced.

Jan 1, 2003

By S C. Dominy

The Minerals Education Australia program is offering a tertiary learning environment for the global mining industry. The Minerals Council of Australia has instigated this initiative, which is run by the Minerals Tertiary Education Council. The program is a pioneering partnership between the Australian minerals industry, Australian governments and key Australian universities. It is designed to deliver key undergraduate and postgraduate courses for tomorrowÆs minerals industry professionals in the fields of geoscience, mining and minerals engineering and metallurgy. The flagship course for geoscience professionals is the G3 Masters program. This is a coursework-based degree supported by the Minerals Tertiary Education Council, and a partnership between James Cook University, the University of Tasmania and the University of Western Australia. These partners represent the leading-edge providers of minerals geoscience education and R&D in Australia. The G3 program provides the full spectrum of post-graduate training skills in exploration, mining and economic geology topics.

Jan 1, 2003

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By J A. Rumball

Measuring cyanide in the leach liquors associated with high copper and/or sulfide ores is a non-trivial exercise. It is well known that copper complexes with cyanide and reduces the amount of cyanide available for gold leaching. What is not so well known is that the rhodanine end point overestimates the amount of cyanide available for leaching in the presence of copper. Sulfide ions also interfere with a rhodanine end point titration, although this is less of a problem as the black silver sulfide precipitate formed clearly indicates to the operator that something is wrong. Thiosulfate, which forms readily from the alkaline oxidation of sulfides, causes an overestimation of the cyanide available for leaching due to the formation of Ag(S2O3)-. The net result of these observations is that rhodanine is rarely of value as an end point indicator in complex solutions. It generally overestimates the amount of cyanide available, providing plant metallurgists with a false sense of security. Potentiometric titrations are generally much more capable of accurately measuring cyanide in complex solutions. The interfering effect of copper can be resolved and it is even possible to estimate the copper concentration using the inflexions associated with the titration of CN- + Cu(CN)43- versus Cu(CN)32-. Using the potentiometric method sulfide ions can be determined before the cyanide measurement is made due to the formation of AgS2, although the electrode will foul with repeated measurements. Thiosulfate can also be distinguished from cyanide with a potentiometric titration. Rhodanine and potentiometric titrations are both affected by the pH of the liquor. At pH 9.2 half the cyanide will be present as CN- and half as HCN(aq) with only the CN- being titratable. This does not hold in the presence of a buffer active around pH 9. In the presence of sufficient buffer, both the CN- and HCN(aq) are titrated. Ca(OH)+ may buffer the pH when large amounts of lime have been added.

Jan 1, 2007

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

The origins of instrument application in the Mineral Industry are discussed. Development of measurement techniques pertinent to the industry is described as is the early application of mini-computers. The current application of microprocessor based equipment and the benefits obtained from this range of equipment are discussed. A speculative opinion as to what future instrument development may offer the industry is outlined.

Jan 1, 1985

By Hamilton LH, Campbell PB

Since fundamental research in applied coal petrography is carried out mostly on polished surfaces, backscattered electron microscopy is most applicable for studying coal in the SEM. By employing this technique coal macerals can be easily identified , and information on the relations between maceral groups, mineral matter and trace elements are highlighted by grey level contrasts. This type of information is valuable in coal technology and cannot by normally revealed by the light microscopy (e.g. the distribution of inherent mineral matter).

Jan 1, 1989

By P J. Mathew

Quality and process control in the iron ore industry is based on measurements of ore grade from blast holes through to shiploading. Traditionally this has been carried out using conventional sampling, sample preparation and analysis methods, but on-line analysers are now being introduced for monitoring the grade of important process streams. Once a conventional sample has been collected, it can be analysed for a wide range of elements. On the other hand, on-line analysers measure only a few selected elements, but they provide rapid feedback on grade, which is important for effective quality and process control. In both cases, the linkage between mining, processing and final blending operations at the port is crucial to ensuring that product quality is maintained while production targets are met and the life of the resource is maximised.

Jan 1, 1998

By C Fenton

The mining industry is a relatively minor user of water, which has historically been largely soured from private schemes. Frequently mines are often located in areas with limited available water resources. Water reform is increasingly affecting access to water for new mining projects and mining companies are being required to consider the value of water and the implications of reliability in their planning. This paper seeks to briefly review the water reform process in Australia and how it is affecting the mining industry with reference to some recent project experience.

Jan 1, 2003