Search Documents

By K S. E, S C. Parker, T K. Kundu

Understanding the fundamental principles governing the reactions at surfaces has always been the goal of theoretical surface science. The atomistic simulation techniques have been used to calculate the surface structures and the stability of quartz and wollastonite, and their adsorption behaviour in the presence of molecular and dissociative water, and the two widely used collector head group molecules of methanoic acid and methylamine. The dissolution behaviour of wollastonite has also been modelled. The calculated surface energy, hydration energy and reaction energy values have been examined and discussed in the light of flotation literature. These studies have given an insight into the interactions at atomic level, which indicate that modelling techniques should be capable of predicting the adsorption behaviour and to design the selective collector molecules, which is of central importance to the mineral processing technique of flotation.

Jan 1, 2005

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second, in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.

Jan 1, 1944

The products from beneficiation present themselves at opposite ends of the spectrum, and yet numerous synergies exist in the preparation of coking coal and hematite iron ore products for their common export markets. Returning to the coal side of the business with Anglo Coal following a five-year sojourn in WA with Hamersley Iron, has provided the opportunity for comparing and contrasting some of the key synergies of the supply chains of both bulk commodities.Comparisons include consideration of things like: resource evaluation (especially quality aspects), run-of-mine handling and preparation, beneficiation, product handling and transportation, quality assurance and customer awareness, value-in-use and impacts on iron and steelmaking, and supply chain environmental aspects.Inherent within these are several other notable contrasts including: æseamsÆ and æorebodiesÆ, rocks and minerals, rejects and tailings, oxidation and weathering, suppliers and users, and marketing and purchasing, to name but a few.This paper covers some of the more interesting of these synergies and raises some potential opportunities for sharing knowledge and innovation between the two areas of activity in the future.

Jan 1, 2005

The fragmentation of whole rock by blasting has an influence on the subsequent loading, hauling and crushing operations. However, no method of calculating the frag- mentation has yet been developed. This paper gives a method of calculating the fragmen- tation for the simplest form of blasting, i.e. cratering. Cratering consists of the detonation of a spherical charge of explosive in a blasthole breaking to one free surface. This paper gives a method of calculating the extent of the system of radial cracks generated by the explosive in the rock. This system of radial cracks is then used to calculate the fragment size distribution curve from blasting. The calculated curves are shown to be in good agreement with experiment.

Jan 1, 1977

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

By Conley R, Payne I

The Vickery Coal Mine commenced open cut mining operations in May 1991. All overburden and interburden is drilled and blasted for excavation by dragline or hydraulic excavator. The mode of operation adopted from the feasibility studies requires that throw blasting of the overburden be used to assist dragline productivity.This paper reviews the development of the drilling and blasting practices with particular emphasis on the throw blasting of the overburden and optimisation of costs. This review includes analysis of the pre-production drilling and blasting feasibility studies by comparison with actual results.

Jan 1, 1992

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has been attributed by previous authors to a detergency process. This publication shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1969

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

According to the temporal and spatial distribution of regional metallogenesis, the Pacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinen- tal metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly re- lated to S-type granite of crustal source, that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of min- eralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metalloge- netic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

China has abundant bauxite resources, but these resources are mostly of a diaspore, which has a feature of low Al2O3 to SiO2 mass ratio, typically ranging from four to six. Compared to other materials, this kind of raw materials consumes more alkaline and energy in the process of metallurgy, and incurred a high alumina production cost. To solve this problem, researchers in China have done a lot of work on removing of the silicon from bauxite. Under the impetus of these works, in 2003, the first flotation plant of diasporic bauxite in the world was constructed in Zhongzhou, Henan, China. Seven years of operating experience shows that this technology can signifi cantly reduce the costs of following-metallurgy processing. These efforts are an important reference for the processing of similar resource. In general, for Western scholars it is diffi cult to fully understand these works because most of them are published in Chinese. In this paper, a detail introduction for the research progress on China bauxite de-silica flotation was presented, these works involved crystal chemistry, wettability of bauxite minerals, collector and modifi er in bauxite fl otation and flotation practice, etc.

Sep 13, 2010

A substitute for rutile can be produced by leaching natural or pre-treated ilmenite in hydrochloric acid. Ilmenite in its natural form is an extraordinarily inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite so that it can be leached with dilute hydro- chloric acid (=2O% w/w) can be enhanced by pre-treatment steps of oxidation and re- duction. The temperatures at which oxidation and reduction are carried out have an effect on both the kinetics of these steps and the leaching kinetics and optimum temperatures for oxidation and reduction are 950 and 850¦C respectively. The mechanism of leaching of iron from pretreated ilmenite and the effects of rate of agitation, temperature, acid con- centration and addition of ferrous chloride to hydrochloric acid on leaching kinetics and production of fines are discussed in the paper.

Jan 1, 1984

By B Delaney

For worker safety, mining companies are required to stop production and inspect hoist ropes. Visual inspection is generally done daily and EM inspection occurs every three to four months. During visual inspection, rope speed is generally reduced so an inspector can look for problems. In EM testing the LMA and LF traces are printed on a paper strip chart and a skilled operator interprets these traces. Mining companies only find large defects during visual inspection and are sometimes concerned about the content of EM trace information. This paper will present research outcomes that show how muck can be hoisted while performing a complete visual rope inspection at full speed. Other research results will show that digital signal processing can increase the amount of information available to the EM rope inspector. The research was funded by Inco, C-CORE, three AMIRA International sponsors and six sponsors from the Canadian Deep Mining Research Consortium (DMRC). The research will be commercialised in 2005.

Jan 1, 2005

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By Ghiani M, Currelli L, Fuganti A

the results of an experimental study aimed at beneficiating a complex ore containing bastnaesite and other rare-earth minerals, with associated barite and fluospar are illustrated. Owing to its minero-petrographic, physico-mechanical and structural characteristics, the crude ore is not amenable to classic concentration methods, such as flotation, magnetic and gravity separation. Therefore the technical feasibility of selective disintegration followed by size classification has been studied, whereby bastnaesite and the other rare-earth minerals can be concentrated into the finest size fractions. Leaching and subsequent extraction of rare-earth metals by liquid-liquid separation represents the final stage of beneficiation.

Jan 1, 1993

By R A. Eggleton and, P de Caritat, K M. Scott

The Portia Au and North Portia Cu-Au-Mo prospects are located on a magnetic structure called the Benagerie Ridge Magnetic Complex, comprising varying pyrite-bearing Proterozoic albitite, phyllite and carbonaceous phyllite. The prospects are covered by up to 75 m of Cainozoic sediments, which comprise from top down, surface soils, Quaternary sediments, the Miocene Namba Formation and the (Late-Oligocene?) Portia Unit.The Portia Unit is dominantly clay-rich with local sand-rich base and it fills palaeo-topographic lows and a palaeo-valley that incised into the weathered basement rock (saprolite). This sedimentary unit hosts the majority of the Au grains found at Portia, with additional Au grains also present in the underlying saprolite. The North Portia prospect comprises saprolite hosted Cu-Au-Mo, with elevated concentrations of As-Pb-V present in the northern part of the prospect. These two groups of elements are delineated using factor analysis, and are regarded as the pathfinder elements for the North Portia mineralisation.Secondary Cu minerals including covellite and native Cu are present in the lower saprolite, and are stable under reducing conditions in the saturated zone.In the upper saprolite (unsaturated), Cu, Au, As, Mo and Pb are associated with Fe-oxides, mainly goethite and hematite. Saprolite leached of Fe generally contains low pathfinder elements concentrations.

Jan 1, 2004