Search Documents

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By Stewart R

Potential acid rock drainage from the destruction of metalliferous sulph-ides is recognised as a critical factor in the design and economics of any mining venture. While this realisation is relatively new, mining companies have embraced the issue with the aim of scientifically quantifying the magnit-ude of the problem, specific to indiv-idual properties.Coinciding with the development of the open pit mine at Porgera, a comprehensive assessment of the potent-ial for the formation of acid rock drainage was initiated in 1991. Detail-ed study of the mineralogical charact-eristics of all rock types, along with extensive test work to determine the maximum potential of rocks to generate and consume acid (known as acid base accounting or ABA), has been conducted. Correlating this with the known and interpreted geology of the open pit has indicated a strong relationship between rock type, sulphur content and the acid base character. This relationship is used daily as a simple, cost effective means for classification and management of the variety of material types produced from the minincx operation.

Jan 1, 1994

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

The Taupo Volcanic Zone (TVZ) is the largest active volcanic belt in New Zealand. It is

Jan 1, 1987

With the exeption of the United States, Canada and Russia, oil has not been around in quantity near world centres of population. Production: in Western Europe is insignificant. Japan is without production as are Australia, Southern Africa, India; Brazil, Chile, New Zealand and China. The United States is, however, a large importer of crude oil. The very fact that oil is produced generally away from centres of population means that it has to be carried by sea to the area in which it is required. There is, therefore, a constant flow of oil around the world in very definite channels.

Jan 1, 1962

By P Jago

KCGMÆs Fimiston Open Pit, located in the centre of the historic Golden Mile, is situated above some 3000 kilometres of old underground workings. These workings, both level and vertical, present significant safety and operational problems in the pit. One of these challenges is in safely drilling void areas so that they can be charged and blasted effectively. Current drilling practices in these areas require machines that can only drill 115 mm holes on a smaller pattern than the standard blast pattern. This results in more time and cost to both drill and charge these areas. Any other method currently available to drill out these areas involves putting operators in a potentially hazardous situation by being too close to the void area being drilled. Not effectively drilling and blasting these areas leads to hazardous situations further in the mining cycle including oversize, large toe and uncollapsed voids. Ineffective blasting also causes reductions in mining productivity and mine to mill performance. In response to these issues, KCGM has commissioned the implementation of a fully remote controlled DM45 blast hole drill rig to drill out selected void areas. The remote system, installed in conjunction with Ausdrill Ltd and GM Mining Electrics, is designed to operate similarly to a tele-remote bogging system with the operator controlling the drill rig from a separate control cabin via radio signals and video feed. This allows KCGM to drill in areas of higher risk without exposing the operators to voids. The drill rig will also be able to drill standard patterns through some specially selected void areas, reducing costs and extra time associated with drilling and charging void affected areas. The remote rig is expected to provide a number of benefits, both in the drilling process and in further downstream operations. Costs of drilling in void areas are expected to decrease with standard patterns instead of smaller patterns being drilled. Safety and operator comfort are also expected to increase through removing the operator from the pit floor. Blasting is also expected to see significant improvements through increased ease of charging void areas (because of larger holes and standard patterns), more consistent patterns resulting in less secondary blasting and toe and an overall improvement in the speed and cost of charge-up practices. This more consistent blasting will also improve shovel productivity, crusher performance and overall mine-to-mill efficiency. This paper presents an overview of the development of the remote controlled system, including modifications that have occurred since commissioning. It explains some of the problems encountered and how these have been solved. Key issues for operational success will be identified and explained with a view to making future implementations easier. Factors used to assess the performance of the remote controlled rig will also be explained in further detail and used in a preliminary assessment of the rigÆs feasibility.

Jan 1, 2003

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

It is often assumed that geotechnical investigations or studies for open pit mines are confined to providing a slope design. However in an operating mine, the design is only one component of a mine geotechnical program. Reviews of slope designs are ongoing throughout the mine life. The concept of Pit Slope Management has been formulated because the design only entails one component of a total program that contributes to a safe, efficient mining operation. Risk is a normal part of mining. Effective management allows the risk to be contained or controlled. If the slopes are not effectively managed there will be increased risk for the operation. Experience has shown that utilisation of Pit Slope Management coupled with a broad base of experience to define the key controls on stability, provides a pro-active, objective approach. The reasoning is deductive and relies on the behaviour of the ærocksÆ. Once the key aspects are defined, studies are well focused, implemented as required and the risks can be effectively managed. When the key controls on stability are poorly understood reasoning is typically more ægut feelÆ. Under such circumstances studies, if carried out, may meet short-term objectives but often ignore the long-term objectives. Hence the risk to the project is greatly increased. This paper presents several case studies highlighting the above aspects and present elements of the Pit Slope Management Program approach which have been successfully utilised by the author to manage risk in mining projects.

Jan 1, 2003

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By Hayes P. C

The kinetics of reduction of PbO-silicate melts in CO-N gas mixtures at 900¦C have been studied. Rea~tion rates were measured by moni- toring the CO2 content of the product gas. A wide range of gas and melt compositions and gas flowrates have been investigated. The overall reaction rates in heterogen- eous systems are typically characterised by a steady increase as the gas flowrate is in- creased. At low flowrates the processes are limited by gas film mass transfer. At high flowrates it is expected that the rates will tend to maximum values determined by either the rate limiting chemical reaction or diffusion in the condensed phase. In the present series of experiments it has been found that for any given gas composition the overall reduction rate goes through a maximum with increasing gas flow. The maxima, which occur at relatively low gas flows, are more than an order of magni- tude greater than those observed at high gas flowrates. The results of these and other experiments are presented and analysed. Possible rate limiting mechanisms in the reaction system and their implications regarding commercial reactors are discussed.

Jan 1, 1987

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

The weathering of different types of base metal deposits in the semi-arid environment of the Lachlan Fold Belt of western New South Wales affects the geochemistry of outcropping ironstones (gossans) and derived soils. W eathering of the pyrite- and pyrrhotite-rich mineralisation at the Elura Zn-Pb-Ag deposit leads to highly acidic conditions and strong depletion of Cd and Zn throughout the profile. There are local attainments of high concentrations of Ag, As, Ba, Cu, Hg, Pb, Sb and Sn in the profile and As, Ba, Pb and Sb are still highly anomalous in surficial material (ironstone and soil). However, at Parkers Hill, in the Mineral Hill Field, the primary Zn-Pb mineralisation is pyrite-poor and so weathering is not as acidic as at Elura. Thus, although Ag, As, Cd, Cu, Sb and Zn may be concentrated at various levels in the Parkers Hill weathering profile, Cu and Zn (as well as As, Pb and Sb) are retained in surficial ironstones in essentially the same abundances as in primary mineralisation. Thus, variations in the suite of geochemical indicators present in ironstones and residual soils are likely to reflect differences in the original mineralogy and the degree of acidity produced during the weathering of base metal mineralisation. Hence, an understanding of weathering processes is necessary to fully interpret exploration geochemical data.

Jan 1, 2004

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

By Fyodorov A. N, Sorokin M. L, Komkov A. A

The Vanyukov Process is a bath smelting technology, that has been investigated for over 25 years and since 1977 has been in use on an industrial scale. Results of trials that have been carried out at the various pilot facilities over the past 15 years are considered in this paper. Both the main process aspects, design of the pilot furnaces and metal distributions are presented for consideration. Experience of the smelting of copper, copper-nickel, copper-zinc, nickel, lead, and pyrite concentrates is analysed.

Jan 1, 1992

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

By Masters I. M, Ozberk E, Chalkley M. E

The integration of iron rejection as hematite with the Sherritt two-stage zinc pressure leach process has been investigated on the laboratory scale. The two-stage pressure leach process is applicable for a greenfield zinc plant, or for replacement of the conventional roast-leach circuit in an existing zinc plant. An excess of zinc concentrate is used to accomplish acid neutralisation in the first stage of pressure leaching, and the residual concentrate in the first stage residue is treated with an excess of acid solution in the second stage of pressure leaching to yield high zinc extraction. Integration of hematite precipitation with this process allows for the potential sale of the iron residue, greatly decreasing the residue disposal problem. Two flowsheets containing the desirable features of both of these processes are described in this paper, along with laboratory Results.

Jan 1, 1993