Search Documents

By Y Gu

Based on the mode of occurrence, gold is classified into three categories: microscopic gold, submicroscopic gold and surface-bound gold. Microscopic gold, or visible gold, refers to gold minerals in which Au occurs in a substantial amount, such as native gold and electrum. Submicroscopic gold, ie invisible gold, refers to gold contained in the structure of other minerals (mainly sulfides) in minor to trace amounts. Surface gold is the gold that was adsorbed onto the surface of other minerals during mineralisation and subsequent oxidation or metallurgical processing. Gold mineralogy has a significant impact on its extractive metallurgy. Gold process mineralogy helps address problems related to gold ore processing. It is widely used as a predictive and troubleshooting tool in gold ore processing, and provides useful information on process selection, flow sheet development, recovery improvement and reagent consumption optimisation. This paper will begin with the classification of gold ores, and will focus on gold mineralogy and how it impacts extractive metallurgy through case studies.

Jan 1, 2008

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

Parallel lenticular orebodies occurring at the C.S.A. mine of Cobar Mines Pty. Ltd. are mined by mechanized cut and fill stoping over the full strike length. Access is provided for each stope lift from an inclined drive adjacent to the orebody. Mobile drill jumbos mounting hydraulically-operated booms are used for drilling upholes which are subsequently charged with ANFO explosive.Close control of drilling has been found essential for good back conditions and to ensure optimum fragmentation.Broken ore is transported from the face to the main ore pass by rubber-tyred, diesel-powered, load-haul-dump units. Initially, the units trammed ore to the main pass via the incline drive. As the stopes advanced and the lead distances increased, stope passes were developed in the wall rock and raised concurrently with each stoping lift. The passes terminate in drawpoints and production loaders are used to transport ore from the drawpoints to the main ore pass system.Two parallel ore pass systems have been developed to cater for both copper and copper-zinc ores. These systems terminate above a 48 in. by 60 in. jaw crusher. The crushed ore is conveyed to a traversing rock box and thence to one of two crushed ore bins adjacent to the main hoisting shaft. A loading station conveyor is interlocked with the winder to provide automatic ore hoisting.All phases of ore handling have been mechanized as completely as possible. Results to date indicate this policy has been vindicated but highlight the need for tight operating control and close liaison between operating and maintenance personnel.

Jan 1, 1969

As this district is so far distant from the other mining centres and its mode of approach so circuitous, I am afraid that many residents of other portions of the Commonwealth never think of paying this" Australia's Silver City" a visit, to learn personally the many and various lessons everywhere available, and to become familiar with the really wonderful and interesting features and deposits (which pature has so lavishly bestowed in the mineralogical world) yet seemed to almost ignore or overlook when disposing of topogr,aphical beauties of landscape and vegetation) unless professional or business duties require their presence here. So it is to those whose life is necessarily spent in other parts of the States where they answer their call of duty, and yet feel an interest, either for business or other reasons, that my paper is specially addressed and prepared, and for that reason I witl endeavour to make my remarks more of an explanatory than a dictatorial nature. I feel sure that there. are many members of our Institute who are much more familiar, and have had many more years' experience in the various methods of timbering, filling, and ore extraction, etc., than myself, but I hope that over I6 years' experience in connection with mines and engineering works, the last six of which have been spent in Broken Hill, where, I have been very closely connected.

Jan 1, 1903

By I J. Holland

Located in North West Queensland, XstrataÆs Mount Isa Copper Operations (MICO) is one of the largest underground mines in Australia with annual production exceeding six million tonnes of ore with average copper grades of three per cent. As at 30 June 2006, the Ore Reserve inventory totalled 87 Mt, with annual diamond drilling planned at >40 000 m in order to convert existing resources and test and define exploration targets. The role of the geology department within MICO is to collect, interpret and communicate relevant geological information to ensure the optimal extraction of ore. Routine underground inspections across multiple ore sources are undertaken and the information derived is then distributed to a range of professionals, operational personnel and management. The information is a æreal-timeÆ geological view for the stakeholders. Ongoing data collection and interpretation has developed a strong geological input to all mine planning processes within MICO. This has created strong synergies between mine planning professionals and a throughput benefit has been seen all the way to the concentrator. The MICO geological framework also provides avenues for a geological focus away from short-term production requirements, and as a result significant orebody scale observations and patterns have been realised that have led to an increase in the accuracy of geological and resource models. This has provided practical benefits for short-term scheduling and production, whilst enabling the realisation of long-term benefits that have a strong potential to increase the volume and value of the MICO resource. This paper will discuss the various mine geology contributions at MICO and illustrate some examples where mine geological input from graduate level has added significant value to the MICO business.

Jan 1, 2007

By D S. Clarke, K B. Sporli

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins. The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

By J W Shields

The aim of this paper is to present a concept or model regarding a particular geological environment where gold orebodies occur in the Pine Creek Geosyncline and indeed in many other pans of the world. The name GIGIACS (an acronym for Gold In Greywacke In Anticlinal CrestS) is proposed to label this concept or model. The name Saddle Reefs (which has been in use for many years) is used for gold-bearing quartz veins which often occur in conjunction with Gigiacs. Simple patterns formed by this type of mineralisation at the surface due to different configurations are illustrated. Some examples of Gigiacs and associated saddle reefs are presented from the Pine Creek Geosyncline together with examples from other parts of the world. This concept has been used successfully as an exploration tool and five examples are given. The terms Gicsiacs (for Gold In Carbonaceous Shale In Anticlinal CrestS) and Giliacs (for Gold In Limestone In Anticlinal CrestS) are also used.

Jan 1, 1994

By Unver B

Longwall advance mining is still the predaninant system of coal extraction in the U.K., contribiiting to sane 70 % of underground coal production. Gate roadways providing access to a longwall advancing coal face are maintained adjacent to a rib pillar under high strata abutment pressures and the caving rock mass. It is very difficult to realistically model such access roadways using mathematical or numerical techniques and hence, predict roadway closure. For the past 15 years, a research group in Nottingham University has been engaged in the study of longwall gate roadway stability using observation methods. Gate roadway deformations have been measured in 224 gate roadways and a comprehensive data base has been established. The paper describes the statistical analysis of this database and presents sane. predictive equations which will enable a forecast of the gate roadway closure to he made. Further field work to validate these equations. is described together with an error analysis. The results are very promising and indicate that it is possible to predict gate roadway closure in the U.K. within practical limits of Accuracy.

Jan 1, 1986

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

The South Mine, property of Broken Hill South Limited, is situated at Broken Hill, NSW, Australia, towards the southern end of the main lode. The leases (MLs 7 and 8) cover a length of 2400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1940 feet below the collar of the original main shaft and to 825 feet below sea level. Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30 000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet. A typical assay for a monthly period is 14.4 per cent Ph, 5.6 ozs Ag, and 11.6 per cent Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and zinc concentrates produced are railed to other centres for the extraction of the contained metals.

Jan 1, 1994

By Waller M. D, Whittaker B. N, Singh R. N

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By G W. Croft, L E. Krause

The current copper ore handling systems in use at Xstrata CopperÆs Mount Isa Copper Operations are up to 33 years old and have hoisted over 160 Mt at a rate of around 6 Mtpa. The mineÆs production profile is increasing in line with the optimum life of mine plan to over 6.6 Mtpa, which requires a system utilisation and reliability above that previously achieved. Copper ore is hoisted up the U62 shaft, which forms the central part of the U62 ore handling system. In theory this system can cope with the duty planned if the bottleneck is only the U62 winder. To achieve the planned production rate will require increased focus on reliability of each component in the ore handling system so that ore is available at the shaft for hoisting whenever the shaft is available, and the shaft is available for the maximum practical time. Increased availability will be achieved through the outcomes of the study of each component in the U62 system, and the internal ore handling systems that deliver ore from as far as 2 km laterally and 700 m vertically from the U62 shaft. The true capacity of each component is being determined and current performance is being measured with the aim of improving performance through root cause analysis and engineering out the causes of delays. The program began in March 2004 and this paper describes the progress achieved as of April 2005.

Jan 1, 2005

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

Single station group velocities of fundamental made Rayleigh waves over the period range 15-100 s are carguted for five provincial profiles of the West Pacific. Based on recordings of earthquakes around the West Pacific by the W~ (World Wide Standard Seismic Network) stations AFI (Afianalu), HNR (Honiara), WEL (Wellington), PAR (Raratonga) and RAB (Rabaul). The inversion of the derived dispersion curves for average shear velocity-depth structure of the crust, LID and LVL shows that (i) the over-all structure beneath the profile 'westernSamoa-Micronesia-Mariana' is in between that of regions 3 and 4 of Pacific Ocean (Yu and Mitchell, 1979), except that the velocity is slightly lower, (ii) the uppermost mantle beneath the 'Vitiaz Trench' profile between AFI and HNR is similar to that of region 2 of the Pacific - in other words, thin LID and thick LVL; (iii) the structure beneath the ' Ibnga-Keradec Ridge' profile has a thick crust with thick sediments, and LID-LVL velocity and thickness are similar to region 3 of the Pacific; (iv) beneath the profiles ' Tonga/ Kermadec Trench events-RAR station' the structure is intermediate between regions 3 and 4 of the Pacific Crean; (v) from decomposition of the 'Solomon-meriana' profile, the structure beneath the Cntong Java Plateau has a thick crust with thick sediments and the uppermost mantle is similar to that of region 3 of the Pacific clean.

Jan 1, 1990

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

The Mount Morgan massive sulphide body occurs in a volcanic sequence of Lower or Middle. Devonian age, which is subdivided in the mine into "Upper mine porphyries", "Banded mine sequence", and "Lower mine porphyries". This sequence is intruded by latite, Mount Morgan Tonalite (360 million years), and late Permian dykes. Distribution of macroscopic ore textures and minerals in the orebody are discussed and evidence is presented indicating the pre-Tonalite, Devonian age of the orebody.

Jan 1, 1974

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985