Search Documents

Palaeomagnetic work on the red beds of the Hervey Group from central N.S.W., and on the Mount Eclipse Sandstone from the Ngalia Basin, Central Australia, reveals a pre-deformational magnetization from the Hervey Group, which indicates a semi-equatorial palaeolatitude during the latest Devonian or earliest Carboniferous and a syn-deformational magnetization from the Mount Eclipse Sandstone which places Australia at a palaeolatitude of about 70¦ ¦ 20¦S during the early Late Carboniferous. By comparison with the existing data from Australia, the new results indicate that: (1) Australia (and thus eastern Gondwanaland) underwent a rapid southward movement of about 60¦ during the late Early and early Late Carboniferous, (2) the Lachlan Fold Belt has been part of cratonic Australia since at least latest Devonian or earliest Carboniferous, and (3) the New England region and cratonic Australia were at a similar palaeolatitude during earliest Carboniferous, but they may have undergone the rapid southward movement separately.

Jan 1, 1987

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By M J. Sale

The Epithermal and Mesothermal Gold Prospectivity Modelling Projects recently completed by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250 000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, which was to stimulate mineral exploration and investment in exploration, has been successful with new companies acquiring new tenements and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were undertaken at a national scale and consequently not all exploration data were compiled into the prospectivity models. HPD New Zealand Ltd recognised the value of the prospectivity modeling work and committed exploration funds to continue the modelling process started by the projects. They recognised the need to compile the remaining data and run the models again to allow detailed exploration targeting.

Jan 1, 2004

The Mineral Resources Act 1989-90 came into force on 1 Septem- ber 1990 and the Second Schedule of this Act set out the Savings, Transitional and Validation Clauses to this legislation. The Second Schedule gave rise to a number of interesting situa- tions however due to the fact that the time set aside to attend to these matters (the prescribed period) has now expired, with the exception of the points raised below, most of these situations are now history and are of no relevance. The Transitional provisions of the Second Schedule provided for a three month "prescribed period" in which certain actions were required to be undertaken to ensure tenements granted or applied for under the repealed legislation transitioned into the framework provided by the Mineral Resources Act. This Second Schedule of the Mineral Resources Act highlighted a number of anomalies which are still worthy of mention and are listed below.

Jan 1, 1991

By Q Zhou, Y Ma, J Zhu, R L. Frost, P Yuan

A series of organoclays with different surfactant arrangements were prepared by ion exchange. The resulting organoclays were investigated using a combination of characterisation techniques, including X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric measurement (TG) and N2 adsorption-desorption. In the present study, the pores within the organoclays were discussed on the basis of the micro- structural parameters, including BET-N2 surface area, pore volume, pore size, surfactant loading and distribution. The results show that both BET-N2 surface area and pore volume decrease from low to high packing density of the surfactant as the average pore size increases. Two basic organoclay models were proposed for hexadecyltrimethyl- ammonium bromide (HDTMAB) modified montmorillonites: 1. the surfactant mainly occupied the clay interlayer, and2. both the clay interlayer space and external surface were modified by surfactant. This study demonstrates that the pore structure of the resulting organoclays has a significant influence on the sorption efficiency and mechanism of p-nitrophenol onto the organoclays.

Jan 1, 2008

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By O N. Antzutkin, W Forsling, K J. Pike an

The adsorption mechanism of three different O,OÆ-di-alkyl-dithiophosphate (dtp) collectors, K[S2P(OR)2] with R = Et, i-Bu and i-Amyl, on the surface of synthetic chalcocite (Cu2S) was studied by means of solid-state 31P CP/MAS NMR spectroscopy. The morphology changes on the conditioned Cu2S surfaces, in the collector concentration range 0.1 - 10 mM, were also monitored with scanning electron microscope (SEM). In order to assign Cu(I)-dtp species on the surface of Cu2S, the corresponding bulk Cu(I)-dtp compounds, which are clusters of the monovalent copper containing either Cu6(antiprismatic) or Cu8(cubic) cores, were synthesised, and characterised by means of solid-state 31P CP/MAS and static 65Cu NMR. Further investigations on the crystal habits of the bulk systems were carried out by powder x-ray diffraction and SEM. A comparative analysis of the 31P chemical shift and chemical shift anisotropy (CSA) data estimated from the experimental NMR spectra of the polycrystalline bulk Cu(I) dialkyldithiophosphate complexes was used for assigning the 31P resonance lines in the NMR spectra of the collector treated Cu2S powder samples. The species formed on the synthetic Cu2S surfaces were assigned to polycrystalline phases of: Cu6L6 with L = Et2dtpû, Cu6L6 and Cu8L6(S) with L = i-Bu2dtpû, and Cu8L6(S) with L = i-Amyl2dtpû. A heterophase autocatalytic step process of both formation and growth of solid CuxLy (L = R2dtp, x = 6 or 8 and y = 6) complexes on the collector treated Cu2S surface is proposed. A possible role of the oxidised form of dithiophosphate collectors, bis[di-alkyl-thiophosphoryl]-disulfane (disulfide), is discussed in terms of a specific self-redox reaction. The second order quadrupolar lineshapes in 65Cu NMR spectra were simulated and the interaction parameters, CQ and hQ, for the bulk dialkyldithiophosphato-copper(I) complexes were obtained.

Jan 1, 2005

By Groves D. I

The Norseman-Wiluna Belt (Fig.1) is a richly mineralized (production 1900 tonnes Au), Archaean greenstone belt, up to 800km long and 200km wide, which forms the major part of the Eastern Goldfields Province within the Yilgam Block. The Belt evolved ca. 2700 Ma ago as an oblique-slip mobile belt between flanking portions of an older greenstone terrane. Volcano-sedimentary successions in the Belt represent two distinct tectono-stratigraphic associations. Sequences of metamorphosed caic-alkaline intermediate to silicic volcanic rocks interlayered with tholeiitic basalts probably represent the remains of a dissected Archaean volcanic arc (or arcs), and sequences composed dominantly of ultramafic to mafic lavas and intrusions, with minor interflow tuffaceous, sulphidic or cherty sediments are interpreted as remnants of the floor of an ensialic marginal basin (Barley and Groves, 1988). Ultramafic volcanism at Kambalda has been dated at 2692 ¦ 2 Ma (Claoue-Long et al., 1986). The dominantly volcanic associations are locally overlain by coarse clastic sedimentary succes- sions. The Belt is also typified by major north- to north-northwest-striking fault systems, shear zones, and tectonic lineaments, many of which are traceable for more than 300km. As well as defining the boundaries of the belt, these structures have accomodated much of the regional strain and acted as conduits for hydrothermal fluids during deformation, metamorphism and mineralization. As a result, most of the epigenetic gold deposits in the Belt occur in subsidiary structures related to these fault systems (Eisenlohr et al., 1988). Deformation involved oblique compression resulting in a closely spaced network of low-angle faults (thrusts) as well as upright folds and oblique- to strike-slip faults (Archibald, 1987; Veamcombe et al., 1988). This was accompanied by regional metamorphism and granitoid emplacement. At Kambalda, regional deformation and metamorphism were synchronous with the emplacement of the Kambalda Granodiorite which has been dated at 2662 ¦ 4 Ma (Hill and Compston, 1986), approximately 30 Ma after volcanism.The tectonic history and style of deformation of the Norseman-Wiluna Belt are similar to those of Phanerozoic oblique- slip mobile belts at continental margins, which are also a major source of hydrothermal gold mineralization.

Jan 1, 1988

Depending upon the probability one assigns to project go-ahead, up to $10 billion (1978 figures) could be required for resource based projects in Australia in the next decade. In the past major resource projects were readily financeable against sales contracts. In the future the complexities imposed by such matters as political risk, inflation, currency movements and environmental and other socio- economic considerations on project development costs and returns may require a different approach. This paper addresses itself to the ramifications of providing development finance for resource based projects in the future - and in particular examines such factors as project completion guarantees, sales contracts, protection against exchange rate fluctuations, interest rate structures and debt/equity ratios as each relates to the provision of finance. TABLE OF CONTENTS SECTION 1 : Introduction SECTION 2 Factors Affecting Project Financing in the Next Decade SECTION 3 Some Aspects of Financing New Projects in Australia in the 1980's Conclusion

Jan 1, 1979

In 1975, following a programme of solution characterization and small scale laboratory test work, a pilot plant was constructed to treat waste liquors from the Risdon works. The plant was designed basically to neutralize liquor to a desired pH, and to flocculate, thicken and then filter the resultant pulps. The primary objective was to purify waste liquors to stand- ards set by Tasmanian environmental regulations and at the same time to provide design data for construction of a full scale treatment facility. Waste liquors were divided into two groups, those from the Zinc Plant, and those from the Acid and Superphosphate Plants, and were treated independently. To satisfactorily purify Zinc Plant waste liquors the following reaction sequence was required: 1. Neutralization to pH 10.5 (with aeration for Mn removal). 2. Further reaction of neutralized pulp with Na2S at an addition rate of typically 5 mg of S2-/litre of liquor treated to remove Cd.

Jan 1, 1977

During the 1960s chalcocite ore was mined from the Black Rock open cut. A large amount of this uneconomic material was not treated by the No 3 Concentrator at the time and as a consequence a surface stockpile was created which contained 750 000 tonnes of material at an average of 1.5 per cent copper.Laboratory trials indicated that due to oxidation, an average of 25 per cent of the copper was water soluble and the remaining copper was leachable using a sulphate/ferriclbacterial leach. On the basis of these trials it was decided to investigate the feasibility of producing copper via a leach SX-EW process. The investigation proved the process was feasible, so began the design, construction and commissioning of a 10 tpd (cathode copper) Copper Leach SX-EW Pilot Plant. CMPS Pty Limited in a joint venture with John Holland Engineering Pty Limited were awarded the turnkey contract for the design, construction and commissioning of the Pilot Plant.

Jan 1, 1993

By Hedley TP

Success for underground coal mine operators in the 1990's and beyond will be dependent upon better understanding of the dynamics of their operating environment, and extension of emerging technologies to reach new levels of output and productivity. The Collieries Division of B.H.P. Steel International Group clearly identifies with the concept of business/product life cycles - and the need to adopt strategies that can drive the business successfully into the future. Three main thrusts within BHP Collieries Division relate to: 1) Detailed assessment of current mines to determine: a) The real output potential of the current facilities. b) What factors now inhibit the full potential from being realised. c) Opportunities that exist to enhance overall mine performance. 2) Based upon the findings of these studies, putting into place cost effective strategies and systems for the ongoing "tuning" of the mine. 3) of new/improved technology primarily in areas of: a) Coal cutting and underground coal clearance. b) Controlling the overall mine gas Regime.

Jan 1, 1987

By E Nettleton, A Melkumyan

Identification of geology and mineralogy in situ on the mine face is essential if mining processes are to be automated for tasks such as exploration, grading and reconciliation. Hyperspectral data acquired from field based platforms are ideally suited to these tasks, and are set to revolutionise the automated mining industry. Changing conditions of solar illumination introduces variation into the hyperspectral signal, which is unrelated to geology, complicating analysis of data. Thus, algorithms must be able to deal with changing illumination conditions and operate in a consistent and probabilistic framework, which is a prerequisite for data fusion with other sensors. To produce accurate classification maps of geology, algorithms must be developed that are effective under different conditions of illumination.The efficacy of three algorithms to classify hyperspectral data for geology mapping on vertical mine faces was assessed. These algorithms are the spectral angle mapper (SAM), and two machine learning methods operating within a fully probabilistic Gaussian process (GP) framework û the squared exponential (SE) and the observation angle dependent (OAD) covariance functions (kernel). Two experiments were done to assess the classification performances. The first determined the performance of the algorithms by classifying hyperspectral data of known rock samples acquired using a field spectrometer. The GP-based methods had a similar performance, with average accuracies and F-scores of 97 and 88 per cent (GP-OAD) and 95 and 81 per cent (GP-SE), respectively. Average accuracies and F-scores for SAM were significantly smaller (80 and 40 per cent respectively). The algorithms were then applied to hyperspectral imagery acquired from a vertical mine face at different times of the day, under very different conditions of illumination. In contrast with experiment 1, SAM and GP-OAD gave results which were superior to GP-SE and were entirely consistent with geology mapped in the field. Compared with SAM, GP-OAD was less sensitive to the effects of shadow and produced classified images that were less noisy. The GP-SE method failed to delineate even gross changes in geology on the mine face. These results show conclusively that in order to use independent training data (spectral library) to classify imagery acquired under a different set of conditions, algorithms must take into account variability in incident illumination. Measures based on spectral distance are inferior to those based on spectral angle.The OAD kernel within the GP framework (GP-OAD) is superior to the other two methods because:it provides a probabilistic framework;it is insensitive to variability in illumination within and between imagery acquired under different conditions; andit can identify and map geological zones on a vertical mine face using an independent spectral library, without a priori knowledge.

Sep 26, 2011

By A Fareth

Constructed between 1885 and 1891, the New Croton Aqueduct (NCA) in New York State is a 50 km long (31 mi) brick-lined tunnel conveying water from the Croton watershed north of New York City to distribution systems in the Bronx and Manhattan. Except at two siphons, the aqueduct operates as an open channel conduit from the New Croton Reservoir downstream 39 km (25 mi) to the Jerome Park Reservoir in the Bronx. The remaining 11 km (6 mi) is operated as a pressurised conduit and includes a major siphon, of circular cross-section, under the Harlem River. The aqueduct has a flow capacity of approximately 1100 million litres of water per day (13 m3/s or 290 million gallons per day) and supplies on average ten per cent of New York CityÆs drinking water. The CityÆs water supply system is operated and maintained by the New York City Department of Environmental Protection (NYCDEP). This paper covers the work done during the three main stages of the program to rehabilitate the entire NCA: inspections, design and rehabilitation. It also includes some of the more interesting structural findings of the original construction as well as documents and drawings from the NYCDEP archives. The rehabilitation program has been underway in phases since 1993, with inspections scheduled to minimise outages, allowing this strategic aqueduct to remain in service during critical seasonal periods. The open channel flow section of the aqueduct in the north is horseshoe shaped, with inside dimensions of 4.1 m (13.6 ft) in width and 4 m (13.5 ft) in height. The pressurised section is 3.7 m (12.3 ft) in diameter, and includes a 90 m (330 ft) deep siphon under the Harlem River. A total of 163 million bricks were used in the construction, enough to build a 48 km (30 mi) wall around Manhattan Island, 3 m (10 ft) thick and 15 m (50 ft) high.Between 1993 and 1997 a series of in-tunnel investigations were performed in the open channel portion of the NCA, consisting of field inspection, non-destructive geophysical testing, and coring of the brick liner. Between November 2004 and September 2005, a major inspection program was conducted to assess the condition of the 11 km (6 mi) long pressurised section and all shafts, headhouses and blow-off structures along the entire 50 km (31 mi) alignment. Inspection methods included using an underwater remote operated vehicle (ROV) equipped with sonar and cameras to inspect the deep siphon, fibre optics examinations of probe holes drilled through and beyond the brick lining, and core holes and geophysical inspections to assess properties of the liner and behind-the-liner materials. A water pressure and test grouting program was conducted to assess methods and expected grout takes for the rehabilitation work in the pressurised sections. The rehabilitation program is anticipated to be completed in 2010.

Jan 1, 2008

The purpose of this work is to determine the equilibrium-state of the aqueous-solution which is produced by the leaching processes, including natural weathering of pyrite minerals. The latter can lead to acid-mine-drainage (AMD). The ferric iron species (Fe3+) resulting from bacteria-catalysed oxidation of ferrous iron (Fe2+), in the presence of water and air, is known to bring about steady-dissolution of minerals chalcopyrite (CuFeS2), sphalerite (ZnS), pyrite (FeS2), and so forth. Good-aeration, relatively high-porosity and sufficient bacterial activity tend to promote leaching in waste-rock-dumps. The composition of the aqueous-phase that accumulates in the pore-space (or in open-pits) is of practical interest as it would strongly influence the leaching of both sulfide and non-sulfide minerals. Since the reactions among the various ionic species occur relatively fast, the solution-phase may be regarded as approaching a state of virtual-equilibrium and it is possible to determine by computation the respective concentrations of the many dissolved species. For the Cu-Fe-H-O-S system, these species may include: H+, Fe2+, Fe3+, Cu2+, HSO4-, SO42-, OH-, CuSO4o, H2O, Fe(OH)+, Fe(OH)2+, Fe(OH)2+, Fe2(OH)24+, Fe(SO4)+, Fe(HSO4)+, Fe(HSO4)2+, and Fe(SO4)2-. The aqueous-system which may be constituted from appropriate mole-quantities of H2SO4, FeSO4, Fe2(SO4)3, and CuSO4 is in fact the result of various natural processes (reactions) and due respect must be accorded to the extents of these reactions. The present model computes the equilibrium molalities of the foregoing ionic and neutral aqueous species, using the iterative equilibrium constant method that ensures strict-adherence to charge-balance and elemental molar-balance constraints. The dissolving sulfide-minerals (FeS2, CuFeS2) consume Fe2(SO4)3, H2O, and O2 and yield FeSO4, H2SO4, and CuSO4 while the aqueous-phase tends to become progressively acidic (declining pH) reflecting the gradual increase in the extents of sulfide-dissolution reactions. The equilibrium-state of the solution-phase is computed for specific set of values for the extents of respective reactions. The temperature and pressure of the system are 25¦ C (298.15 K) and 101.325 kPa (1.0 atm), respectively. The mica-like minerals such as the biotite [H2K(Mg,Fe)3Al(SiO4)3] tend to consume much of the H2SO4(aq), with the extracted K+, Mg2+, Fe2+ and Al3+ ionic species accumulating in the solution. The precipitation of the jarosites (potassium, hydronium, or ammonium) contributes to the removal of ferric and ferrous species from the solution-phase. In the present work, the emphasis is on predicting the compositions of the aqueous- and condensed-phases with advancing time or increasing æextent of reactionÆ. The results of such calculations are compared to published data on raw AMD (acid-mine-drainage).

Jan 1, 2008

High pressure (-1.2 GPa) Early Cretaceous granulite facies orthogneisses in Fiordland, New Zealand are in tectonic contact with a cover sequence comprising mid-Palaeozoic amphibolite facies metasediments, subordinate metavolcanic rocks and syntectonic granitic orthogneisses. This cover sequence and the underlying granulites constitute upper and lower crustal plates of a mid-Cretaceous metamorphic core complex whose emplacement was linked to continental rifting and the Late Mesozoic breakup of the Pacific margin of Gondwana. Exhumation of the lower plate granulites occurred in two stages. The first stage was associated with extreme attenuationand tectonic denudation of the cover sequence accompanying emplacement of the core complex, leading to rapid uplift of the granulites but without generating the large volumes of Fiordland-derived sedimentary detritus normally expected if uplift and erosion were the only factors involved in unroofing the granulites. Final uplift and exposure of the granulites at the surface occurred mainly during the last 10 Ma in response to transpression across the mid-Tertiary Alpine Fault and/or the obduction of Fiordland continental crust over oceanic crust of the Tasman Sea.

Jan 1, 1990

In Australia, current production of rare earth element (REE) minerals, monazite and xenotime, occurs as by-product from titanium-enriched placers and beach sands. Undeveloped REE resources are associated with carbonatites, alkaline igneous rocks, pegmatites, phosphorites, cemented fluvial sandstones, and uranium mineralisations. The REE are held within a range of minerals including silicates, phosphates, a1uminophosphates, carbonates, and oxides. The development of these REE resources may require new processing and extraction methods. The distribution of REE in the currently mined ore minerals, monazite and bastnaesite, does not match that requested by the market. Exploration for new REE resources should be focused on ores with more marketable REE distributions, particularly with heavy REE, neodymium, samarium, europium and yttrium enrichments. Such ores occur within alkaline igneous rocks, in laterites overlying carbonatites and alkaline igneous rocks, and in placers derived from low-grade regional and contact metamorphic sediments. Lateritic REE deposits may be easily and economically mined by shovel in open pits and are unlikely to require extensive crushing and milling. In addition, lateritic REE clay deposits may be processed by simple hydrometallurgicaltreatment mehtods.

Jan 1, 1991