Search Documents

By Blackwood R. L, Crichton G. P

In recent years, the value to Australia of the introduction of a system of resource rent taxation on the mining industry has been frequently debated. The forms that this rate of return based tax could take, and the impli- cations on government revenue and mining com- pany profitability have been discussed at some length. Further, the selective application of this taxation scheme to certain mining industry sectors has received considerable attention. This study takes the form of a survey of the taxation history of one significant Australian mining venture, the Mount Lyell Mining and Railway Company. The conditions faced by this company during its history are used as a base for the imposition of rent taxation schemes. Comparisons are drawn between the historical taxation liability of the company and that which would have been incurred if a resource rent form of taxation had been in existence. From the results of the study, it can be concluded that while the company can be con- sidered to have been a successful enterprise during most of its history, it has not achieved a level of profitability which would warrant the collection of any form of excess profits Tax.

Jan 1, 1979

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

By Grouhel P

Blasting performance is directly related to the characteristics and efficiency of the explosives used. The selection of the correct explosive for particular blast conditions and objectives depends on the ability to characterise the performance of individual explosive products. Techniques have been developed by the JKMRC to measure explosive performance and assess the impact of explosive performance on blast results. Studies conducted at a number of mine sites have shown that different types of explosives perform quite differently and that the performance of any particular explosive can vary significantly. The principal causes of these variations have been identified and detailed blast monitoring techniques, including the analysis of muckpile fragmentation and shape, have been used to quantify the effects of explosive performance on blast Results.

Jan 1, 1990

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

Towards Improved Hydrocyclone Models - Contributions from Computational Fluid Dynamics

Sep 13, 2010

By Fraser RJ

A Robbins Raise Drill Model 61R was used to provide one 7' diameter shaft 1050' deep in Clutha Development's exploratory mine at Blackwater in Central Queensland and two 7' diameter shafts 1450' deep at their South Clifton mine on the Illawarra Coast of New South Wales.

Jan 1, 1972

Comalco's Bell Bay smelter produces some 94 000 t.p.a. of primary aluminium in the form of foundry alloys, extrusion billet and rolling blocks. The extrusion billet and rolling block are produced by a process, in which molten aluminium is poured into an open ended water cooled mould of the required shape. The bottom of the mould is initially closed off by a dummy or starting block. Primary cooling takes place at the mould wall and secondary cooling is achieved by direct water sprays onto the out side shell of the product. Careful preparation of the molten alumin- ium is essential if stringent alloy specific- ation limits are to be met. Optimum casting temperature must be maintained within a narrow range and metal cleanliness is important to ensure a consistent product. Increased demands of recent years for larger product and higher standards of surface quality and dimensional control have been instrumental in forcing improvements in furn- aces, casting machines and in mould and dummy Doq,

Jan 1, 1977

By Whiting AN

Major changes in the world in recent years are changing the criteria for selection of future developments. Oil prices soared during the 1970's while commodity prices including metals and minerals fell. Many new independent nations, have been created and now control the resources in areas which were once part of great colonial Empires.

Jan 1, 1983

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

Myuna Colliery long term ventilation requirements were included as part of the overall planning of colliery construction and underground development. Ventilation, during the simultaneous sinking of two drifts and the downcast shaft, was accomplished by established methods of ducted exhaust and blower fans. Drivages for the 3 seam interconnections of shaft and drifts were ventilated by extension and duplication of the exhaust systems. Ventilation, for the below seam extension of the belt drift, construction of between seam and below seam bins, and the completion of a circular between seam drift, required a step by step changeover to a temporary main ventilation exhaust fan mounted adjacent to the top of the completed downcast shaft. The second, permanent upcast, shaft was commenced and colliery production started one seam at a time, using the transport drift, while the underground bins, belt and between seam drifts were completed. The uocast shaft was completed and a connection made in the upper seam, completing all contract mining and allowing the main fan to be erected. The permenent twin centrifugal fan system was installed, commissioned and test run to

Jan 1, 1983

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

By Beeby C. j, Fernando W. J, Ming M. Q I, Guang Li Xi

Removal of moisture in steam-fluidized, mainly steam-heated, fluidized beds makes possible significant energy savings over conventional forms of large-scale drying. The systens are described and their applications to brown coal and alumina hydrate are reviewed. In application to brown coal the use of the system to permit meeting diurnal variation in power station output, and the use of triple-effect drying to minimise coal usage and to avoid the necessity of recovering in the turbines the energy in the steam from the last dryer are discussed. To facilitate the rapid adoption of the systems proposed, studies are being made of heat-transfer to dried coal, of moisture equilibrium in pressurized and vacuum systems, of tapered beds as a means of reducing carrier steam and permitting wider size variation, and of the use of carrier solids for drying lump materials.

Jan 1, 1989

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By G MacDonald, B Forsyth, D Corkery, T

An investigation was carried out at Diavik Diamond Mines Inc (DDMI) to identify and quantify the mechanisms through which ammonium nitrate (AN) was entering the mine discharge water. The goal was to develop and complete an investigation of the potential AN loss mechanisms in order to assess their contribution to ammonia in the mine water system. The initial phase of the project involved the collection and analysis of blasting and water quality data that were used to determine the mechanisms by which the ammonia enters the mine water system and to establish a baseline data set for comparison with results from future trials designed to reduce AN loss. Three potential options for reducing AN loss were identified through the first phase of the project. The second phase of the project involved conducting a series of monitored trials with changes made to the drilling and blasting process. The results of these trials were compared to the baseline data set to determine if the changes introduced for the trials had reduced AN losses while producing satisfactory blast results. This paper describes the process for the collection of the baseline data, provides an analysis of the resulting data, discusses the changes made to blasting operations in order to minimise AN loss and describes the results observed subsequent to these changes.

Jan 1, 2007

From August 1962 to June 1976 Peko Mines Ltd. produced Gold Bullion at the Peko Control Mill using 18x24 Denver Mineral Jigs and strake tables. Gold ores treated during this period were obtained from Orlando, Juno and Ivanhoe Mines and from the Warrego Mine after 1974, all in the Tennant Creek Area of the Northern Territory. With the downturn in copper prices Warrego Copper ore mining ceased and the copper Smelter closed down in February 1974, Warrego gold ore continued to be treated in the Peko Concentrator.

Jan 1, 1978

Many volcanoes in western Melanesia have tectonic settings and rock compositions that do not conform to conventional models of arc- trench systems. Part of the reason for this may be that in an environment of rapid tectonic change mantle source regions bear the imprint of former subduction even though subduction has now ceased. Results bearing on this concept and on other important aspects of Plelit nesian v ican ism and tectonics, were obtained in 1982-1986 from >e,:eral marine - geoscience studies in the re,,ii n

Jan 1, 1987