Search Documents

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

This paper examines some of the important aspects of mineral taxation policies and practices, with reference to the mining tax regimes of selected Pacific Rim countries (see Tables 1 and 2). The following subjects are addressed:what is æmineral taxationÆ?, basis for mineral taxation, types of mineral taxes, objectives of the mineral taxation regime, best practices, and mineral royalties. Many countries, in some cases with the encouragement and assistance of international funding agencies, are actively assessing the international competitiveness of their mining tax regimes with a view to attracting investment. However, these countries recognise that the mining tax regime is not the only consideration that is taken into account by prospective investors. The countryÆs geological prospectivity, physical infrastructure, labour force, political risk, and regulatory system are also important factors in the investment decision making process. Although it is probably true that an attractive mining tax regime will not necessarily attract mineral investment, there is a real possibility that an unattractive regime can drive away investment. For example, Hugo Dummett, general manager for discovery at BHP, hinted recently that BHP could cease exploration in Russia in the absence of positive tax changes. Dummett is reported as saying that if taxes æend up being as onerous as they are now, we really have to rethink why we are hereÆ (Mining Journal, London, November 27, 1998).

Jan 1, 1999

By M Hedley

Tracking plant and personnel in mining operations provides multiple potential benefits for a mine including improved safety, better monitoring of production, traffic control and, in the future, monitoring and control of autonomous vehicles. The main techniques currently proposed and used for wireless tracking are radio frequency identification (RFID), signal strength based techniques and time of arrival (TOA) based techniques. RFID provide poor accuracy in the complex radio propagation environment present in mines and does not provide continuous tracking and signal strength techniques. TOA based techniques are potentially the most accurate, however, most current equipment has not realised the potential of the technique. CSIRO has been developing the Wireless Ad hoc System for Positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines and surface operations, where GPS reception is compromised by depth. The system utilises a number of ‘anchor nodes’ that are placed at fixed and known locations within the mine and tags attached to the plant or personnel to be tracked. The system provides an ad hoc data communication network, thus, wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging down to 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of testing in underground and surface operations showing the system achieving high ranging, hence localisation, accuracy.

Nov 22, 2011

By N Wharmby

In recent years in New Zealand there have been a number of tunnelling and deep directionally drilled pipelines projects that have required access shafts. Often these shafts are in urban environmentswhere vibration and high noise levels are not tolerable. There are a number of methodologies that can be adopted dependent upon the shaft plan area, depth and geology.This paper will describe some different methodologies that can be adopted that use piling methods such as large diameter piles, and secant piles. The paper will use case studies to highlight:· construction methodology,· specific methodology issues and constraints,· lessons learnt, and· recommended specifications.The development of piling technologies in New Zealand has enabled the development of cost effective solutions for the construction of deep shafts in sensitive urban environments.

Mar 8, 2011

Cretaceous volcanic activity (Hauterivian Albian) in the Peruvian Andes can be found along the coast of Peru and the western edge of the Andes mountains between 15o30'S and 5o30'S, extending discontinuously in south to Chile and north to Ecuador and Colombia. This volcanic activity formed in three aborted marginal basins; the NNW-trending volcanic Ca±ete and Huarmey, and NNE-trending Lancones basins. These volcanic rocks are predominantly andesitic and basaltic in composition, of calc-alkaline and tholeiite affinity with subordinate dacitic and rhyolitic rocks. One notable feature is the appearance of æocoitasÆ from Ica (14oS) south to Santiago de Chile. These rocks have a calc-alkaline to alkaline affinity. From south to north, the continental crust gradually becomes thinner, allowing mantle material to rise towards the surface. Ophiolitic sequences of this type form a marginal basin in Colombia. Very low-grade regional metamorphism which affects the volcanic rocks also varies gradually from south to north. Between Santiago de Chile and Ica this takes the form of burial metamorphism, with moderate geothermal gradients (20o-30oC/km). Metamorphism in the Huarmey basin is transitional between burial and ocean-floor metamorphism, with very high geothermal gradients (>3000C/km). High geothermal gradients are also apparent in metamorphism of the Lancones basin, though less than the other basins. Ocean-floor metamorphism is present in the ophiolitic sequence in Colombia. Associated mineral deposits in the Huarmey and Lancones basins, and in the north, are of the volcanic massive sulphide-type (VMS). The principal deposits in Peru are Leonila Graciela (20 Mt Zn and Pb) and Tambogrande (40 Mt Cu and Zn). There are also smaller mines and prospects. To the south of Lima, manto-type Cu deposits (CuMT) are found with a mineralogy of chalcopyrites, pyrites, magnetite, actinolite and apatite. The main example is Raul Condestable (10 Mt Cu). Other prospects are present to the south and Chile has some very large mines of this type (El Soldado, Lo Aguirre). The notable differences between the CuMT and the VSM deposits are thought to be the result of the prevailing conditions in the earthÆs crust during the Hauterivian Albian. To the south, calc-alkaline and alkaline volcanic activity in aborted marginal basins, with thicker crust, was thick, produced moderate geothermal gradients associated with burial-type regional metamorphism and deposits of CuMT. In the north aborted marginal basins associated with calc-alkaline to tholeiitic volcanic activity and a gradually thinning crust, produced transitional regional metamorphism between burial-type and ocean-floor type, associated with high to very high geothermal gradients and VMS deposits. In Colombia these conditions led to ophiolite extrusive rocks, ocean-floor metamorphism and also VMS deposits.

Jan 1, 1999

By M W. N Buxton, M S. Shishvan, J Benndorf

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance in terms of produced ore grades and quantity and extraction process efficiency often deviate from expectations. Reconciliation exercises to adjust mineral reserve models and planning assumptions are performed with timely lags of weeks, months or even years.With the development of modern information and communication technology over the last decade, a flood of data about different aspects of the production process is available in a real-time manner. For example, sensor technology enables online characterisation of geochemical, mineralogical and physical material characteristics on conveyor belts or at working faces. The ability to utilise this additional information and feed it back into reserve block models and planning assumptions opens up new opportunities to continuously control the decisions made in production planning to increase resource recovery and process efficiency. This leads to a change in paradigm from a discontinuous method to near real-time reserve reconciliation and model updating, which calls for suitable modelling and optimisation methodologies to quantify prior knowledge in the reserve model, process and integrate information from different sensor sources, back propagate the gain in information into reserve models and efficiently optimise operational decisions in real-time.This paper introduces the concept of an integrated closed-loop framework for real-time reserve management, incorporating sensor-based material characterisation, geostatistical modelling under uncertainty, modern data assimilation methods for sequential model updating and mining system simulation and optimisation. The effectiveness of the framework and the value added will be demonstrated in an illustrative case study.CITATION:Benndorf, J, Buxton, M W N and Shishvan, M S, 2014. Sensor-based real-time resource model reconciliation for improved mine production control – a conceptual framework, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 223–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By E Donskoi

In order to develop downstream processing routines for iron ore and to understand the behaviour of the ore during such processing, extensive mineralogical characterisation is required. To determine mineral associations, mineral liberation and grain size distribution, imaging techniques have to be used. There are two main imaging techniques used for the characterisation of iron ore, ie, Optical Image Analysis (OIA) and Scanning Electron Microscopy (SEM). In this article a QEMSCANTM system is used as an example of SEM methodology and results obtained from it are compared against results obtained by the CSIRO ‘Recognition3/Mineral3’ OIA system.Both OIA and QEMSCANTM systems have advantages and drawbacks. Even though the latest QEMSCANTM systems can distinguish between major iron oxides and oxyhydroxides, it is still problematic for QEMSCANTM to distinguish between iron ore minerals very close in oxygen content, eg haematite and hydroheamatite, or between different types of vitreous goethite.QEMSCANTM also can misidentify minerals with close chemical composition, ie haematite as magnetite and vitreous goethite as haematite. In OIA, iron minerals with slight differences in their oxidation or hydration state are more easily and directly recognisable by correlation with their reflectivity. In both methods, the presence of microporosity can result in some misidentification, but in SEM methods misidentifi cations due to microporosity can be critical. Low resolution during QEMSCANTM analysis can significantly affect the textural classifi cation of particle sections.The main conclusion of this study is that, for low iron content ores or tailings, QEMSCANTM can provide much more detailed information on the gangue minerals than OIA. However, for routine characterisation of iron ores with high iron content and containing a variety of iron oxides and oxyhydroxides, OIA is a faster, more cost-effective and more reliable method of iron ore characterisation. A combined approach using both techniques will provide the most detailed understanding of iron ore samples being characterised.

Jul 11, 2011

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

By Whittle J

Definition of the optimum open pit, whether an intermediate phase or final design, will be sensitive to many factors. The most basic will include geological and mining constraints, mining and processing costs, pit slopes and product prices. The application of the three dimensional Lerchs-Grossmann pit optimization procedure to this task is described for a range of gold deposits. A new approach to the modelling and manipulation of the geological model enables complex geological environments to be assessed, and sensitivity analyses to be developed. Comparisons with manually developed pit designs have been made to validate the results. The computer implementation is simple to use and can be adapted by non-computer professionals at mine Sites.

Jan 1, 1986

With the continuing move towards digital signal based control and measurement, it is inevitable that such technology will be increasingly employed on remote sites. The benefits of increased metallurgical performance, of reduced energy and manpower requirements far outweigh the problems associated with high technology in remote locations, provided that the installation is well thought out from both technical and manpower viewpoints. The new accessibility of vast quantities of process data will uncover previously unthought of savings and profit opportunities but brings with it the responsibility to carefully design the data presentation methods. The resulting changes in installed hardware will force changes in the maintenance and engineering workforce and will affect even the stores and purchasing department methods.

Jan 1, 1985

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By B G. Blacka, O Salisbury, K W. Mills, R G. Jeffrey

Whitehaven Coal Limited operates an underground longwall mine near Narrabri, New South Wales. The mining horizon in the Hoskissons Seam is overlain by a 16–20 m thick unit known as the Digby Conglomerate, a unit that is sufficiently massive to have potential to cause a windblast during first caving at the start of each longwall panel and periodic weighting throughout the panel. A program of hydraulic fracturing has been successfully used to precondition the conglomerate strata to increase its caveability at the start of each panel. This paper presents a system of temperature monitoring that was used successfully to measure hydraulic fractures at Whitehaven confirming their rate of growth, orientation and interaction with previously placed hydraulic fractures.CITATION:Mills, K W, Blacka, B G, Jeffrey, R G and Salisbury, O, 2014. Temperature monitoring of hydraulic fractures used for preconditioning massive conglomerate strata to reduce windblast, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The Australian minerals sector has a shortage of skilled professionals to satisfy an industry that is experiencing renewed vitality. Graduate numbers are low throughout Australia and the world, while economic rationalisation is seeing many educational institutions downsize, or even close, their minerals-related programs. In addition to requiring more entry-level graduates, minerals producers are looking to update the skills of their current workforce to keep up with the industryÆs continuing technological revolution. To address the issue the Minerals Council of Australia (MCA) endorsed collaboration between several Australian minerals producers and a team of universities to generate the Mineral Tertiary Education Council, or MTEC. MTEC recently initiated a venture to increase the availability of professionals with relevant skills to the minerals industry. Primarily aimed at delivering postgraduate programs, the initiative will allow graduates from other disciplines to æconvertÆ to the minerals sector as well as provide professional development training to an existing work force. This venture represents a novel approach in that courses will be delivered by more than one institution and will employ innovative teaching materials with flexible and remote delivery formats. The programs will cater specially for professional development in the minerals sector, which generally requires high flexibility due to the nature of work conditions and locations.

Jan 1, 2004

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan includes mining of the:unmineralised banded iron formation (BIF), Mt Whaleback Shale, Mt McRae Shale, Mt Sylvia Formation, and parts of the Wittenoom and Jeerinah Formation. With the exception of BIFs, all other units contain zones with varying amounts of sulphides and carbon û æreactive shaleÆ. Reactive shale has a propensity to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulphide rich zones also have the potential to generate acid rock drainage (ARD). Mining reactive shale at the Mt Whaleback mine must be undertaken in a safe, efficient and environmentally responsible manner. Key tasks in the mining process include:100 per cent identification of blastholes that may contain reactive shale; 100 per cent correct loading of blastholes with specified blasting products; 100 per cent of reactive shale mined, hauled and dumped in designated overburden storage areas; 100 per cent containment and treatment of ARD water onsite; and ongoing research into ARD, self-heating and spontaneous combustion. Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments.

Jan 1, 2002

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

By Nilmani M, Malone J, Taylor RN, Floyd JM, Gray NB, Fountain CR

CSIRO staff and University of Melbourne staff and students collaborated in an intense programme of investigation on the CSIRO 50 kg Sirosmelt pilot plant.In two days of operation copper matte converting and zinc slag fuming trials were performed, whilst investigation of the process dynamics and process chemistry was carried out. This exercise is an example of the techniques available for process evaluation, which can rapidly advance the understanding of pyrometallurgical operations by use of a team approach covering a wide range of experiments.

Jan 1, 1985

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990