Search Documents

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

By Johnson G. D

Confidence in Yakabindie becoming a truly cost competitive nickel project has risen recently because of: ò the emergence of an economically effective contract mining climate; ò the delivery of cheaper energy via the Goldfields Gas Pipeline; and ò the development of the Yakabindie Process for production of nickel cathode and cobalt by-product directly from sulphide concentrates at site, dramatically cutting capital and operating costs compared to the conventional route. Development of the Yakabindie Process was a result of 'necessity being the mother of invention'. Yakabindie can now break out of the trap of relying on existing downstream processors to treat an intermediate, and instead the project can gain direct market access. The very attractive cost advantages demonstrate that hydrometallurgical processing of sulphide concentrates is a worthy prize. Improved cobalt recoveries, and tolerance of higher levels of magnesium and arsenic than allowable by smelters, are further advantages of this approach. Leach residues are combined with much larger quantities of naturally alkaline flotation tailings and remain at site. As a result the process is more environmentally sensitive than the conventional smelt/refine route, with no sulphur dioxide gas emissions and 'metal only out the gate'.

Jan 1, 1996

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012

By A B. Christie, R Barker

Recent studies carried out to support the development of a strategy for the New Zealand mineral industry by the NZ Minerals Industry Association have included investigations of mineral potential, and the development of scenarios for realising this countryÆs mineral potential by 2010. New economic research is applying a general equilibrium model to quantify the opportunity cost of this potential. The model analyses separately four categories of land (private land and three categories of Crown land) and identifies four distinct mineral classes û precious metals, industrial minerals, coal and aggregate. It investigates the economic effect of the increased availability of mineral resources on the mining industry itself, on other industry sectors and on the NZ economy generally, including its impact on unemployment, GDP and household welfare.The analyses suggest that increases in the level of GDP of between 1.9 per cent and 3.4 per cent may be obtained by utilising New ZealandÆs mineral wealth to varying degrees. The mineral industry sectors are significant beneficiaries under all scenarios; mineral output increases by between two and five times its current level. However, the flow-on effects to the rest of the economy, and to households, are also significant. The analyses show that household income, adjusted for changes in consumer prices, can be expected to increase by between 1.6 per cent and 2.7 per cent. This results largely from increased employment.

Jan 1, 2002

By N Murphy and, S Santomartino, M Cramer

Acid rock drainage (ARD) can have detrimental effects on mining infrastructure, water reuse options and environmental discharge. As a result, some form of short- or long-term treatment is required at many mine sites. Successful treatment depends on a number of factors including the selection of an appropriate treatment technology and its correct implementation. A variety of passive and active technologies are available for dealing with ARD. Passive treatment solutions do not require continuous chemical inputs but take advantage of naturally occurring chemical and biological processes. They are often low cost, site specific approaches and are predominantly used in post-closure situations. Passive systems are well suited to drainage with low acid loads and low soluble aluminium concentrations, and are more effective with highly reduced (ie low oxygen) water. While they are often regarded as permanent fixes, most require some form of ongoing maintenance and all have an engineered life expectancy (ie finite carbonate and organic matter budgets). Passive treatments include, oxic limestone drains, anoxic limestone drains, limestone diversion wells, various reducing and alkalinity producing systems, pyrolusite limestone beds, aerobic and anaerobic wetlands, permeable reactive barriers (organic ¦ carbonate and zero valent iron), slag leach beds, and gas redox and displacement systems (GaRDS). Active treatment solutions require a continuous or semi-continuous activity (eg reagent dosing) to correct water quality issues. They can be engineered to treat virtually any type of drainage or site specific ARD issue, and have no set acid load or redox limitations. Tasks handled by active treatment systems are almost invariably larger and more costly than for passive systems. Active treatment approaches include; pH control, adsorption/absorption, ion-exchange, electrochemical concentration, biological mediation/redox control, flocculation/filtration and crystallisation. A range of generally available and proprietary technologies has been developed around these approaches. Active treatment involving pH correction with alkaline amendments is the most common and cost-effective form of ARD treatment. A variety of fixed plant and portable treatment systems are available. Calcium-based reagents, including quicklime (CaO), hydrated lime (Ca(OH)2) and limestone (CaCO3) remain the reagents of choice for the majority of active ARD treatment worldwide. This is principally due to their widespread availability, non-proprietary nature, and variety of proven dispensing technologies and cost-effectiveness. Limestone, in particular, is a very low cost reagent. However, due to æefficiency of useÆ problems with limestone in passive treatment systems, combined with its very low cost, there has been a recent emphasis on developing active treatment systems that use limestone efficiently. As the requirement for treatment increases, there is a growing emphasis on treatment sludge management and sludge stability. The final choice of a suitable treatment technology is dependent upon water chemistry (eg pH, type of metal contamination, acidity), flow rates, acid load, local natural resources (neutralising materials, topography), climate, site logistics, environmental risk and economics. The benefits and limitations of both passive and active treatment technologies are summarised.

Jan 1, 2003

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

The economic viability of many Southern African massive mining operations is threatened by excessive dilution. In many operations currently in progress, some stopes are experiencing as much as 115 per cent waste ingress reporting to drawpoints. This paper examines the magnitude, causes and types of dilution and presents a set of general principles for the control of dilution in massive stoping operations.

Jan 1, 2000

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

By D Landriault, G W. Wilson, L Langetine and

Engineered soil covers are used for final closure options for both waste rock and tailings disposal facilities. Currently, cover construction requires excavation of appropriate cover material from a nearby site. If no suitable materials are available, the mine operation may have to ship appropriate materials long distances to the site before the construction of the cover can even begin. This has led to the proposal to engineer cover materials using existing waste materials from the mining operation. The paper presented here describes the results of a laboratory scale testing program to evaluate the potential for blending waste rock, smelter slag and tailings for the creation of a suitable cover material at a site in Canada. Tailings from the local mill, waste rock and slag were collected in the field and blended to create a material with an air entry value similar to the tailings and with physical strength similar to the waste rock. Testing indicated this mixed material could be blended at a consistency of a paste and was suitable for pumping. It can also be compacted to a high-density material. The preliminary results show that it may be possible to blend waste rock, slag and tailings into a material that can be utilised in the construction of a water retaining cover.

Jan 1, 2003

The Southern 'B' lode orebody at the New Broken Hill Consolidated Limited (NBHC) mine, Broken Hill, is a continuation of the zinc-rich orebody that was first mined in NBHC in the 1940's. Preliminary diamond drilling in the early 1960's resulted in sufficient information to delineate the southern extension of the presently mined 'B' lode orebody, In 1966 the sinking of a 7.3 metre diameter circular shaft (No. 3 Airway) was commenced to improve the ventilation of the southern extremities of existing workings and to provide a base to further explore and develop the orebody extension. Development on four levels was started in the early 1970'.s to link the existing workings with the new shaft. Three possible mining methods - sublevel open stoping, loader cut and fill with ramp access and sublevel caving - were investigated and the decision was made to mine the orebody by transverse sublevel longhole stopes and pillars with trackless equipment and ramp access between the major working levels.

Jan 1, 1977

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By CorrOa de Araujo A, Salum MJG

The treatment of mining and metallurgical liquid effluents is becoming, everyday, a necessity felt by these industries. Physical-chemical and chemical methods for treating such effluents are generally necessary whenever heavy-metals and other toxic compounds such as cyanide are present. The present paper discusses the use of precipitate flotation as an alternative physical- chemical method that can be applied for the treatment of effluents containing heavy-metals (mainly zinc and cadmium) and cyanide. Examples of laboratorial scale applications on real effluents are given. In both cases precipitate flotation was able to reduce the concentration of toxic components of the effluents at a very high removal rate, generating a solid waste that can either be disposed, re-used or recycled. A cationic collector - dodecylamine hydrochloride - demonstrated to be the best choice of surfactant for the two systems investigated. Sodium sulphide and dithizone were selected for the precipitation of the zinc bearing effluent whereas a copper salt was preferentially used for precipitating cyanide in a form adequate for its recycling envisaging the use of an AVR (acidification - volatilisation - regeneration) technique.

Jan 1, 1993

By J Harris, P Kirsch, R LaBouchardiere

æMining + Health in DevelopmentÆ is a project funded by the International Mining for Development Centre (IM4DC, 2012) to develop a centralised database of corporate sustainability initiatives for managing and improving occupational and public health, based on information extracted from social and environmental reports of major mining, oil and gas (MOG) companies. This register of materials has the potential to increase stakeholder awareness of the unique health risks impacting the minerals industry, employees, their families and surrounding communities, as well as to inform stakeholders on global industry approaches to health management.Data and preliminary outcomes from analysis of different MOG corporate sustainability reports on public health and disease management are presented for six African countries (Democratic Republic of Congo, Ghana, Mozambique, Sudan, Tanzania and Zimbabwe) and six Asia-Pacific countries (Indonesia, Mongolia, Pakistan, Papua New Guinea, Philippines and Vietnam).With the minerals industry facing ongoing rapid growth worldwide, including continuous expansion into developing regions, the æMining+Health in DevelopmentÆ project will inform industry, civil society and regulators of current health management practices and programming among the different sectors of the minerals, oil and gas industries and across various regional operations. This baseline information will serve as a resource for minerals industry managers, providing a forum for sharing best practice health management approaches amongst MOG companies.CITATION:LaBouchardiere, R, Harris, J and Kirsch, P, 2012. Mining and health in development - An inventory of global resource industry health initiatives in developing countries, in Proceedings International Mine Management 2012, pp 75-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012