Search Documents

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By K Nilsson, G Cheong

Troy Resources NL acquired a 70 per cent interest in the Mina Sertpo gold project in Goißs State, Brazil, in 2001 following a successful bid for the highly competitive international tender of a tenement package put out by Western Mining Corporation (WMC). The Sertpo deposit is located on cleared grazing land 380 km west of Brasilia and is 30 per cent owned by Amazonia Mineracao Ltda, a private Brazilian company. It is a small high grade open-pittable orebody with a measured and indicated resource of 108 000 tonnes at a grade of 49.7 g/t for 172 500 ounces using a 2.0 g/t cut-off. Troy undertook the project management and development of the project while Amazonia managed the exploration activities and provided other services as required. The project development involved drilling metallurgical test holes, scouring the world to locate an available and suitable second-hand plant, and arranging shipping to andreconstruction in Brazil.

Jan 1, 2004

The Rum Jungle mine was operated by Territory Enterprises Pty Ltd who mined uranium on behalf of the Australian Government with operations spanning the period from 1953 to the final closure of the mine in 1971. In addition to the extraction of uranium from the open cut pits, copper, manganese and lead were mined and processed at Rum Jungle. During the latter part of the operation, and after the closure of the mine, environmental studies were carried out which were aimed at determining the causes of the pollution at Rum Jungle and identifying a rehabilitation strategy for the mine site. These studies identified sources of heavy metal and acid pollution and proposed a rehabilitation strategy which consisted of 1. recontour, construct impervious covers and controlled surface drainage on, and revegetate three overburden heaps,

Jan 1, 1984

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By Shinnosuke U, Zhang HE

In this paper, it is shown that the higher the pre-activation concentration of copper ions in pulp, the larger the adsorption amounts of copper ions and xanthate on arsenopyrite surface, and the better the arsenopyrite flotability in strong alkaline medium. On arsenopyrite pre-activated with cupric ions, the xanthate adsorption density in strong alkaline medium is approximately equivalent to that of cupric ions. It is therefore concluded that an amount of copper ions adsorb on arsenopyrite surface first, and then an amount of xanthate can (and only can) adsorb dependently on the surface active sites produced by these adsorbed copper ions on the mineral, so that arsenopyrite is kept rather flotable and is hardly separated from pyrite even in very strong alkaline medium. Selectively wiping out the surface copper active sites on arsenopyrite is the key point of successful separation of pyrite from arsenopyrite. According to this theory, a new 'SZLI' (know-how) method was recommended to satisfactorily deal with the difficult separation.

Jan 1, 1993

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

Mining is an intensive resource development industry, where operations are often of relatively short duration and can result in dramatic impacts on the natural environment during the operational period and for many years post mining. An integral component of all mining operations is water û through exploration, resource definition, mine development and operation, rehabilitation and the long-term post-mining land use. Water is a basic requirement in the provision of worker amenities, in drilling, as a means of dust suppression, as a medium for washing or processing the mine product, and as an aid in establishing vegetation on post-mining landforms. Water also plays an important role in mobilising environmental contaminants and is the primary medium for the transport of contaminants off the mine or processing site into the wider environment. It is for this second reason that the mining industry considers water management as a key component of mine management. Cost-effective water management relies on planning that incorporates a total mine system approach commencing prior to exploration and continuing through to rehabilitation and decommissioning. One of the primary considerations that will provide confidence to both government and community at the time of mine closure and lease relinquishment, will be the evidence that any water originating from, or passing through, the mine site is of a quality that will not have any negative impact on the surrounding environs into the future. The role of vegetation in stabilising disturbances to a landscape is well known, as is the recognition of vegetation being a fundamental component of the water cycle through the physiological processes resulting in the transfer of water back to the atmosphere through transpiration. In terms of water management at a mine site, the two crucial issues are the æquantityÆ and æqualityÆ of water that enters a receiving æoff-leaseÆ catchment. In terms of tolerances of the receiving environment, the total load of potential contaminants becomes critical, a reduction in which can be achieved through reduced volumes of water discharged, reduced chemical and physical concentrations of contaminants in that water, and ideally, both. This paper examines the potential role of vegetation in reducing the quantity of water released from a site, and secondly considers vegetation in the role of influencing the quality of that water.

Jan 1, 2003

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

By Lynch K. S, Street R. P

Hamersley Iron&apos;s pellet plant at Dampier involves ore drying, dry grind- ing in ball mills, disc balling and, indurating by use of the straight grate system. After five years of operation, the plant&apos;s output has been increased from the design capacity level of 2 M.T.P.Y. to 2.5 M.T.P.Y. Steps taken in equipment modifica- tion, improvements in process control, and changes in maintenance procedures are described.

Jan 1, 1973

By R-H Yoon

A turbulent flotation model has been developed by considering the subprocesses of collision, attachment, detachment, and froth recovery. AbrahamsonÆs model (1975) of infinite Stokes number is used to model collision, while the attachment and detachment subprocesses are modelled by considering the kinetic energies required to overcome the energy barriers and the work of adhesion, respectively. The energy barriers are determined by considering various surface forces, including electrostatic, dispersion and hydrophobic forces, while the kinetic energies are determined from the particle velocities at close separation distances from air bubbles. The latter has been determined by modifying the turbulent root-mean-square (RMS) velocities of Liepe and Moeckel (1976) and Schubert (1999) in view of a lubrication theory. In calculating the RMS velocities, it is assumed that a flotation cell is subdivided into low and high energy dissipation zones. The model predictions made by varying various hydrodynamic and surface chemistry parameters are consistent with flotation practice.

Jan 1, 2005

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By N Kojola, A Vickerfält, J Huss

The possibility of using an acidic autogenous hydrogen direct reduced iron (H-DRI) slag as a basis for vanadium extraction is investigated. For a raw material to be suitable for producing high-quality FeV, the vanadium oxide content should be sufficiently high and the phosphorus oxide content in a tolerable range. Therefore, the feasibility for vanadium extraction relies on fulfilling two demands: the predominate partitioning of phosphorus to the metal and vanadium to the slag. Correspondingly, the behaviours of phosphorus and vanadium in the Al2O3-SiO2-FeOx-VyOz-P2O5-Fe system were studied experimentally. Slag, 10 g, was put in contact with liquid iron, 30 g, for different durations (2–24 hrs) in closed alumina crucibles at 1873 K. The slag composition was varied between 33.1– 49.3 wt per cent Al2O3, 27.1–46.7 wt per cent SiO2, 16.6–30.1 wt per cent FeOx, and 2.5– 8.8 wt per cent V2O3. The equilibrium phosphorus distribution was 0.42, while the vanadium distribution ranged from 7.6 to 43.4, increasing with the Al2O3- and the FeOx-content.

Jun 19, 2024

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton&apos;s Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991