Search Documents

The initiation of cast Pentolite primers by detonating cord has been examined by the combination of two different experimental techniques with computer simulation by the finite element hydrodynamic code DYNA2D. In the first type of experiment, the cord/primer system was placed in a water aquarium, and photographed using a high-speed image converter camera. This highlighted the emergence of the detonation front through the primer surface and the generation of shock waves in the surround- ings. Numerical simulation was used to interpret the experimental record, establishing where the cord had induced buildup to detonation inside the primer. The second experiment used the plate dent test, where the primer was placed in contact with a block of metal (here aluminium), with the resul- tant dent in the metal surface being a measure of primer output. Detailed numerical simulation of this test confirmed that the observed dent was caused by the development of a complex series of shock waves inside the Primer.

Jan 1, 1988

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

The Agnew Mine No. 1 Ventilation Shaft is the largest diameter shaft blind drilled in a hard rock mining environment. The selection of this method of shaft development was based on achieving an accelerated mine development and exploration programme. Drilling the shaft from a pre-sink depth of 73m commenced on March 22, 1982 and the shaft was stopped due to rig structural problems at a depth of 750m, 280m from the designed depth, on February 12, 1983, 137 days behind schedule. While problems with rig mechanical availability, cutter life and lost drilling tools in the hole hindered progress and escalated costs, penetration rates above prediction were achieved and both the speed and safety aspects of the method were well demonstrated.

Jan 1, 1983

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

The Great lady gold deposit presented the challenge of providing a new grade control system for an usual type of orebody in the Eastern Goldfields. Mineralisation occurs as secondary enrichment about a quartz sand - granite saprolite contact 30m below surface. The ore horizon, which averaged 2.5m thickness, was near-horizontally disposed in contrast to the typical steeply dipping, shear hosted deposits of the region. A trial mining operation was undertaken on the richest, most continuous portion of the deposit to test the economic viability of this type of orebody. Controlling and minimising vertical ore dilution was considered crucial to the profitability of the operation.An understanding of the grade distribution combined with the practicalities of mining produced a grade control system which allowed for the mining of 1/2rn composited grades on level lm benches. Ore mining was combined with strict monitoring of levels, truck destinations and ore boundaries. Ore reconciliation results showed this system to be effective.

Jan 1, 1990

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By J Pan, T Chun, D Zhu, Z Guo, J M. Young, T C. Ooi

With the rapid development of the Chinese steel industry, the strong demand for iron ores has led to huge imports of various iron ores from all over the world. As a relatively new force in the iron ore world and an important raw material supplier, Fortescue Metals Group (FMG) has achieved an annualised production rate of 100 Mt of iron ore fines. Typical blends were designed to simulate sinter blends employed in Chinese steel mills, and to determine sintering properties and metallurgical performance of blends comprising FMG Rocket fines in pilot sinter pot. It is shown that the sinter of typical blends comprising 15 - 20 per cent rocket fines possesses excellent sintering properties and metallurgical performance. With Rocket fines substitution for competitor ores in a typical customer mill blend comprising fully imported fines, the sinter productivity and tumble index increased from 1.45 t/m2h and 62.0 per cent to 1.54 t/m2h and 64.0 per cent, respectively, while attaining similar reducibility index and reduction degradation index at lower solid fuel consumption.CITATION:Zhu, D, Guo, Z, Ooi, T C, Chun, T, Pan, J and Young, J M, 2013. Sintering and metallurgical performance of blends comprising Fortescue Metals Group rocket fines, in Proceedings Iron Ore 2013 , pp 519-524 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Nickel Rim Depth Cu-Ni-PGE deposit, discovered by Falconbridge Limited in 1993, illustrates several trends in exploration in the Sudbury area. Recent discoveries tend to be deep, high grade, footwall hosted, close to or straddle property boundaries and made using a multi-disciplinarian exploration approach that integrates economic considerations with geology, metal geochemistry and geophysics (borehole EM). The Nickel Rim deposit occurs down dip of Inco's Victor Deep deposit (4.2 million tonnes at 2.25 per cent Ni, 7.30 per cent Cu) in the eastern margin of the Sudbury Igneous Complex (SIC) at a depth of 2650 m. Before commencing drilling an economic evaluation was done to determine the minimum size needed to be economic at the expected depths and determine the expected value of an exploration venture. The subsequent surface exploration program discovered a drill indicated, undiluted mineral inventory of 1.6 million tonnes of 1.58 per cent Ni, 10.13 per cent Cu, 4.17g/t Pt and 3.50 g/t Pd including 519 000 tonnes of 4.13 per cent Ni, 25.53 per cent Cu, 9.76 g/t Pt and 8.42 g/t Pd. The deposit is hosted by gneiss, migmatite, gabbro and pseudotachylite (Sudbury Breccia) 100 m below the base of the SIC.

Jan 1, 1996

By T Atchison

In-pit crushing and conveying (IPCC) systems have come under growing scrutiny as a perceived mitigation to fuel and equipment price fluctuations, labour shortages and the need to move everincreasing volumes of material. Individual vendors and delivery organisations are now offering a sometimes confusing array of systems, particularly for the dig and dump side operations.One system does not suit all operations. This paper seeks to document the factors that should be considered in assessing the suitability of different IPCC systems, with a focus on dig side equipment layouts in particular. These factors include the productivity of the systems, interactions with the drill/blast and bench operation sequence, the ease of relocation, flexibility to changes in the reserve, scalability and compatibility with other elements of the system.

Jul 11, 2011

By Hayes P. C

The reduction of small, dense zinc oxide (ZnO) samples in CO/CO2, and CO/N2 gas mixtures has been investigated at temperatures between 900 and 1100¦C. The microstructural characterisation of the reacted and partially reduced samples was complemented with measurements of the rates of the reactions. The mechanisms and kinetics of reduction of zinc oxide were found to be dependent upon the CO partial pressure, the oxygen potential of the gas mixtures, temperature and degree of reduction.

Jan 1, 1991

By L Sandery, S Light

Within 22 months of commencing decline development, the Prominent Hill Ankata Underground Project achieved its full production rate of 1.2 Mt/a.In 2010 construction of the Ankata Underground Project was approved. Decline development commenced in November 2010 and the turnout for the first sublevel was reached by August 2011. The first stoping ore was produced in the first quarter of 2012 and production was successfully ramped up to full production during the third quarter of 2012.Diamond drilling commenced in October 2011 and was conducted concurrently with the underground development. This presented challenges as mining and production targets had to be balanced with underground exploration activities. To achieve production on schedule, without adversely affecting the diamond drilling program and future development, meticulous and adaptive planning techniques were required. This included involvement from engineers, geologists, underground operators and underground diamond drillers.The granularity of these planning techniques allowed the management and prioritisation of development and diamond drilling down to an almost hourly basis. A constant flow of information from drill assay results was fed back into the planning systems. This resulted in a constantly evolving mine plan as the orebody was further refined. High priority areas were identified and targeted to allow continued development and a successful rapid ramp up to full production.CITATION:Sandery, L and Light, S, 2014. Managing the diamond drilling interactions in commissioning the Ankata underground mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 75–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

By K Sommerville, J Parkinson

"Open pit mines today have more technology and data available. The challenge is to effectively use resources to analyse and identify mine productivity improvements. AMC Consultants Pty Ltd (AMC) has completed more than 100 benchmarking studies worldwide. In the process of gathering cost and productivity data, insights have been gained on how mines are using data to drive productivity. This paper aims to share good practice on using data, what benchmarks operations should be aiming for, where mines are currently sitting, high value areas to target, and how to best prioritise improvement to meet operational goals.A key purpose of data is to assist in managing and improving operations. Key information is used to drive meetings, decisions, budget estimates and reports. Safety, equipment productivity, available stocks, grade and spatial reconciliation are examples of where data is important for management systems. The key is to keep reporting simple whilst maintaining access to source data for troubleshooting and analysis.Some operations still have paper-based reporting systems. Some operations collect data directly off machines and instruments, use cameras and have off-site control centres. The level of technology is a fit-for-purpose choice.Comparisons of productivity assumptions commonly used in feasibility studies with good practice productivity numbers sourced from AMC’s benchmarking database will be shared in this paper. A typical activity mining cost breakdown will highlight where the high value areas for productivity improvement sit.In addition to examining the productivity of each mining step it is also important to examine the impact on the mine plan. Equipment numbers, strip ratio, grade and material hardness can impact the results of bottleneck analysis. A bottleneck example case study will highlight how productivity and other factors can be used to identify and prioritise improvement opportunities.Keep it simple. Use only the critical data for meetings, decision-making, reports and plans. Knowing and communicating the key performance indicators (KPIs) you are striving for aligns the operation and prioritises improvement plans.Citation:Parkinson, J and Sommerville, K, 2016. Getting the Most Out of Technology to Drive Mine Productivity Improvements, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 84–93 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012