Search Documents

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By G Danckert

The key technical theme of ‘orebody knowledge’ has been applied by Rio Tinto in the Pilbara iron ore precinct from 1966, when operations first started there. It forms the basis of present day application, as well as planning for the future.This paper will review how the early towns and mines commenced and how they formed the basis of Rio Tinto’s early operations, on which the Pilbara precinct has been based. A profile of the last decade of Pilbara growth will be highlighted, together with the current integrated network of mines, rail and ports and the next generation of expansions.The paper will specifically describe the Rio Tinto process of significant resource evaluation, including comprehensive drilling programs and the conversion from resource to reserves. It will also describe the overall mine planning process, both from the strategic view, as well as for short-term mine plans.The ability to innovate in resource development will be discussed. This will include not only the technical dimension of changing cut off grades, use of low-grade ores and managing low-grade stockpiling and beneficiation, but also the broader application of new technology and innovation in the iron ore business.

Jul 11, 2011

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Jones

A common problem in the mining industry is that company exploration groups operate in relative isolation to the rest of the company; resulting in poor knowledge transfer (Qureshi and Briggs, 2006) and often priority conflicts with mine geology, operations and project departments. In recognition of this problem, Newcrest created a Minerals Division responsible for stewardship and governance of mineral assets across the value chain from reconnaissance to rehabilitation. It was recognised at an early stage that effective collaboration both internally and externally would be required to improve decision making, deliver faster cycle times and improve governance.Collaboration in companies is generally associated with the introduction of new IT functions. However, modern IT-based collaboration systems and practices are relatively simplistic compared to the long-standing practices associated with collaboration and knowledge management in science and engineering disciplines such as geology and mining.The authors of this paper have started a trial of a 12-point plan for effective collaboration, which recognises that significant efficiencies can be gained and barriers to future success removed if more effective collaboration can be achieved between science and engineering divisions in a company along with external professionals and with the collective intelligence (Tapscott and Williams, 2006) of the outside world. To meet growth aspirations some companies, like Newcrest Mining Ltd, are adopting this comprehensive, step change approach by moving from a closed model the isolates mine geologists to an open and collaborative model that uses IT visualisation systems strategically. The paper describes how an open model provides people with the right work environment and the right information at the right time, which will help individuals and workgroups to work more collaboratively day-to-day. The aim is to achieve speed, focus and mitigate risk through an environment where everyone and anyone can contribute effectively (Cisco, 2008).

Aug 22, 2011

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Hoffmann

Given that each year, 30–40 per cent of mining industry deaths are attributable to failures of vehicle interaction controls (EMESRT, 2023), the mining industry is now armed with a growing body of knowledge from EMESRT (Earth Moving Equipment Safety Round Table) and ICMM (International Council on Mining and Metals) global vehicle interaction initiatives over the past years, that enables mining companies, OEM’s and technology providers to work together to develop and implement more effective controls and drive the adoption of capable solutions. Leveraging 20 years of experience as a global technology provider of Proximity Detection System (PDS) and Collision Avoidance System (CAS) solutions for surface mining operations, Wabtec Digital Mine Technology shares key insights for ensuring the effective selection, implementation and integration of these technologies into existing mine site controls and mining operations for effectively reducing vehicle interaction risk enabling mines to drive towards ‘zero-harm’ objectives. Topics covered include: alignment with industry best practice for controlling vehicle interaction risk by EMESRT and ICMM, importance of the maturity of EMESRT levels 1–7 vehicle interaction (VI) control framework, managing expectations that PDS/CAS is a ‘silver bullet’, alignment with industry functional – performance – technical requirements, proximity detection versus collision avoidance, sensor performance and fusion and limitations, rules engine intelligence critical to mitigating nuisance alarms during normal operations, system health monitoring and reporting, human factors engineering and operator acceptance, implementation strategy, installation standards and quality control, change management program, training programs, reporting and data analytics with actionable insights and maintenance strategies. Insights will also be provided on the challenges moving from EMESRT levels 7 (operator awareness) and 8 (advisory controls) to level 9 (intervention controls) as it’s a journey not an out-of-box solution, the growing demand for coexistence of CAS and Autonomous Haulage Solutions (AHS), functional safety approach, value added systems integration and the applicability of new emerging technologies.

Apr 16, 2024

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

This paper presents an overview of the current status of mine water management in South Africa. The regulatory framework within which mine water management operates is set out, based on the principles and policies embodied in the relevant legislation. The status of the gold and coal mining industries, with regard to water management, is presented on the basis of studies that have been undertaken to develop water and salt balances for these industries. While the data is not available to quantify the status of ARD in South Africa, the range of typical mine water quality problems faced by South African gold and coal mines is presented. The status quo, problems and challenges relating to mine water management are presented and discussed. It is shown that, while there have been major strides in the last decade, and mine water management and treatment in South Africa has moved onto the forefront of mine environmental management, important problems still persist. There is still a significant amount of improvement required, particularly in the field of prediction of water quality deterioration and the application of such predictions to the identification of management actions that can be applied to prevent or minimise mine water pollution in the shortmedium- and long-term.

Jan 1, 2003

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

By J Light

Since 2019, the mine planning team at Olympic Dam has been establishing and maturing a shift from deterministic to probabilistic scheduling techniques. This paper outlines this journey undertaken by the mine planning team, key learnings from implementation and further work required to increase the level of planning maturity. Olympic Dam (OD) is a highly variable, polymetallic orebody with a vertically integrated value chain from operations to final product. The processing plant has a tight set of quality constraints which are managed through timing of stopes from varying parts of the orebody. Value is eroded for the operation when forecasted quality of the mine feed encounters disruptions from unplanned changes to the timing of stope starts. As production has moved from the historic Northern Mining Area into the more geologically complex Southern Mining Area, average stope size has reduced, resulting in increased mining fronts required to meet production targets. This has created a problem of increased schedule complexity and difficulties in identifying and communicating resource priorities within a large set of individual stope critical paths. The problem was approached by considering each stope as an individual project constructed by teams working across multiple projects at any one time. The operation could then be considered a multi-project environment with shared resources and enables the application of Critical Chain Project Management (CCPM) to the mine plan. Key to CCPM is the addition of time buffers to protect the critical path of a project form upstream or downstream processes. Implementation of time buffers protects the stope start date against compliance to plan variance. The monitoring of each time buffer consumption, as a proportion of total construction activities completed enables proactive prioritisation of resources. This resulted in an increase in the number of stopes starting in accordance with the mine plan, simplified communication of priorities to all levels of the operation, increased compliance to plan and a clear measure of schedule risk during planning routines.

Mar 29, 2023

By Kanchibolta S. S, Brunton I, Tapia-Vergara F

The Split digital image processing system has been implemented in three Australian mines for analysing the size distribution of rocks from the images taken from muckpiles, conveyor belts and tipping trucks. This paper presents an overview of t

Jan 1, 1998

By R H. Knight

Production mine geology must be accurate and efficient in order to reduce risk and ensure that ore value and mining operation revenue are maximised. Present grade control practices are commonly based on outmoded and inaccurate 2D geological mapping techniques where spatial relationships are estimated by eye, sketched by hand and projected to arbitrary reference planes. The 3D mapping approach outlined in this paper integrates 3D photogrammetric imagery with implicit modelling techniques to enable more accurate grade control and reconciliation in underground mines. High-resolution stereo photographs are taken of daily ore development headings. Ore contacts are traced directly on a 2D face photo using a stylus and rugged tablet. Area-weighted face grades are estimated and calculated on mapped 2D face planes. In the office, a 3D photorealistic mesh is processed and georeferenced. 2D face mapping data is transformed into its actual 3D location and true 3D mine mapping is performed by digitising oriented 3D polylines representing ore contacts and other geological features directly onto the image surface. Three-dimensional spatial relationships are fixed, eliminating the projection error of traditional 2D methods. Ore envelope and waste solids are modelled within the closed, drift-round mesh. Volume-weighted ore envelope and round grades, as well as round volume and tonnage, are calculated. Ore/waste classifications, grade, tonnage and per cent dilution are quantified per round, visually assessed in 3D and reconciled with short- and long-term models on a daily basis. Updated geological continuity models provide geological guidance in development headings under geological control and accurate 3D structural and form-line mapping improves definition drilling and stope planning. Three-dimensional imagery provides a permanent detailed survey and geological record of mine workings that can be revisited virtually to reinterpret geological ore controls in light of new observations and insights. In addition images can be used to monitor daily production performance, create training scenarios for miners, engineers and geologists and prepare management presentations. This approach adds value to underground mines by improving the accuracy and efficiency of mine geology practices. The method is particularly effective in mines with visually distinct and geometrically complex orebodies, such as those in the Balmat zinc mine located in New York State, USA, which are used to illustrate the method.CITATION:Knight, R H, 2017. 3D mine mapping – improving grade control and reconciliation in underground mines using photogrammetric imagery and implicit modelling techniques, in Proceedings Tenth International Mining Geology Conference 2017, pp 203–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The paper describes the design of the dilute medium and medium recovery circuits installed at the coal preparation plants at the Cornwall Coal Company's Fingal Mine, and the BP Coal Australia's Howick Mine. These circuits maximize the use of clarified water for rinsing to improve the mass transfer of adhering medium from the coal surface into the carrying liquid, and have been combined with the use of a two stage magnetic separator. The separator utilizes a conventional concurrent first stage and a counter-rotation second stage. This combination results in high medium recoveries during both normal operation, and start up and shut down phases when large quantities of medium can be lost from a conventional circuit. Overall losses using this circuit have been estimated to be, 200g/t, over a twelve month period. Further advantages in plant operation are also obtained, especially steady operating conditions in the centre-tube pump tank, lower slimes contamination of the product, and lower quantities of non magnetics trapped in the separator concentrates. The techniques are particularly suited to incorporation in circuits treating coals containing high percentages of sticky and difficult clays, as are found in the Walloon coal measures.

Jan 1, 1987

By C Simpson, J Market

The process of sampling blasthole cones utilising personnel to manually shovel material into sample bags is a long-standing industry accepted process. However, this method has several drawbacks, including the safety issues around having personnel performing manual sampling in a harsh environment and the variability involved in getting a human to repeatedly get a ‘shovel full of dirt’, and make it always representative. Geophysical blasthole sampling, or utilising a Downhole Assaying Tool (DHAT) has been tested and has now begun implementation at many iron ore sites throughout the Pilbara region, Western Australia. This method uses a geophysical tool to capture data within blastholes, and together with a semi-autonomous logging platform to minimise risks around manual handling, delivers a multielement proxy-assay which can be utilised by the mine geology team to accurately domain the orebodies. Logistically, the combination of a specially designed tool and semi-autonomous truck are the way forward for a safer and more data-robust blasthole sampling practice. The method utilises a neutrongenerating geophysical tool and linked elemental spectroscopy sensor, which measures the response of the material surrounding an open hole. This delivers results at submetre intervals. These results are then utilised, similar to blasthole sample results, to map out areas within the blast pattern that are ‘ore’, ‘waste’, or ‘other suitable grade’. This paper outlines a project that has been in ‘proof of concept’ at selected Fortescue sites over the last few years with testing of these tools carried out on reverse circulation (RC), diamond drill and blastholes. The method is now being implemented at operational hematite mine sites. Fundamentally, the method adds more than enough value to justify its implementation. The aim is that these learnings will enable the greater industry to adapt, implement and improve their mining practices. Ultimately, the outcome will be greater value in mining for the industry by having a larger volume of good quality data to make reliable decisions on material movements, minimising ore-loss and dilution, and maximising the value of our current and future orebodies.

Nov 8, 2021

By A J. Gunson

The Norman B Keevil Institute of Mining Engineering, or the Department of Mining Engineering (the Department), at CanadaÆs University of British Columbia (UBC) is addressing the integration of sustainable development concepts into mining education and research on behalf of industry and society. Over the past decade, the DepartmentÆs education and research model has been evolving to incorporate collaborative and multidisciplinary strategies, where sustainability initiatives are taught in classes, supported in research and discussed in a voluntary collective of mostly graduate students û the Sustainability Working Group (SWG). The SWG has brought together a diverse array of disciplines from academia, industry, government, non-governmental organisations (NGOs) and mining communities. The operational mechanisms and structure of the SWG have enabled momentum to be gained through several multidisciplinary educational and research networking initiatives. It acts to attract new students with diverse backgrounds, foster innovative research, develop relationships and networks, and create the space to discuss progressive ideas and projects. The original cohort of SWG graduate students laid the foundation for sustainable research initiatives within the Department at UBC. Novel research has incorporated topics such as: community resilience, artisanal small-scale mining, sustainability indicators and corporate social responsibility, environmental assessment and impact benefit agreements and the recycling of waste. Propelled by the support of the Department and inspired by the works completed, a host of new graduate students have embarked on their research quests to integrate sustainability principles into their projects. Such projects include: social impacts and benefits of mining, artisanal small-scale mining, community health, the production and transport of mine pollutants, mine waste management, mineral process plant design and the evolution of community education and mine policy. This paper reports on the departmentÆs continuing research and development towards an understanding and evaluations of the ongoing contributions of mining to sustainable development.

Jan 1, 2009

By J Jones, J Blunt

"The requirement for environmental approvals and associated environmental impact assessments (EIAs) is now commonly regarded as a key milestone and body of work during project development. EIAs can be undertaken at various phases during project development, generally either:\ during the scoping or prefeasibility studies, where limited project information is available and the mitigation and management measures of the EIA become a set of criteria and commitments that control project design during the feasibility study, as an iterative approach whereby mitigation and management measures are developed through an integrated process with the engineering team, and measures are included in the feasibility study cost model following the feasibility study, where detailed project design information is available, the cost model is complete, and the EIA is an assessment of a fixed project with limited opportunities for mitigation and management measures to be integrated into engineering design. This paper investigates the advantages of integrating EIA into life-of-mine planning during the feasibility study phase, using the Tampakan Copper-Gold Project (the Project) as a case study. The Tampakan Project is located in the Philippines on the southern island of Mindanao. The Project involves the proposed development of three main areas of infrastructure:a large-scale, open pit copper-gold mine and associated mine site infrastructure (including tailings and mine waste storages, fresh water dam, concentrator, etc) a power station, port and filter plant (PPFP), located approximately 60 km from the mine a pipeline and transmission line linking the mine and PPFP sites.Examples of engineering measures developed through an iterative process to mitigate and manage predicted environmental and social impacts include design of water management infrastructure, modification of the disturbance footprint (eg roads realigned to avoid critical habitat) and realignment of project infrastructure to minimise impacted water catchments.CITATION:Blunt, J and Jones, J, 2012. Integrating environmental impact assessment into life-of-mine planning, in Proceedings Life-of-Mine 2012 , pp 143-152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012