Search Documents

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By S R. Pecover

AustraliaÆs opal and sapphire mining industry has fallen from its peak in the 1980s and 1990s into a significant low today. This is not due to exhaustion of the resource, but instead an over-reliance of the Australian miner on achieving a fair price for the gemstone product from offshore middlemen dealers. Gemstone and geological research is also at a low as Federal higher education expenditure has fallen with research institutions relying increasingly on private funding in an environment of restricted autonomy and flexibility for researchers. What little remaining research skills the universities have is being bled into the private sector as a result of the mining boom and encouraged by lower than average academic salaries. Nevertheless, some highly innovative research has been taking place, often by self-funded individuals and retired academics simply with a desire to advance the understanding of the particular branch of science in which they are interested. New models for the formation of sapphire and opal are now beginning to be applied to the exploration for these gemstone commodities. This research, together with well thought out plans for managing the gemstone product through its value-adding steps to the jewellery retail level, has the potential to bring about a resurgence in the Australian gemstone industry.

Jan 1, 2008

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

By Bromley JC

Eimco Great Britain, a division of Baker Mining Equipment Company, was contracted to develop a hardrock tunnelling machine in conjunction with British Coal. The objective: a machine to cut rock up to 170 MPa compressive strength yet retaining the flexibility of roadheader type machines. This flexibility to encompass mobility, wide range of excavation shapes and sizes, simplicity of design and use, compact size, and efficient cutting operation. Current roadheaders operating in hard material are characterized by: 1. Severe machine vibration 2. Bouncing of the boom away from the rock 3. Very high pick wear 4. Inability to sump head in bad floor conditions The reasons for this poor performance can be attributed in part to: 1. High speed of cutting head rotation 2. Inability to hold boom against rock while cutting variable hardness strata. To overcome the problems described, a new articulation method was developed utilizing four hydraulic rams to "lock" the boom in position on one axis and four hydraulic motors to rotate the boom for cutting via a turret arrangement. The slide mounted turret is hydraulically advanced for sumping into the face, independent of the machine base. To transfer cutting forces back to the rock, the machine base is held rigidly in the excavation by floor to roof or side to side rams. A cutting head mounted on the boom rotates at very low speed, but with very high torque.

Jan 1, 1987

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

By O A. Aladejebi, S Mitra, T Singh, D J. Pinson, S, S J. Chew, T Honey

Currently, many commercial sinter plants are exploring the potential addition of high-grade iron ore concentrates to improve the sinter grade. A better understanding of the ore blend, granule behaviour and green bed properties is critical to making this change and maintaining productivity in the sinter plant. This study compared the performance of a laboratory scale granulation drum to a commercial scale unit. The blend used was an Asia-Pacific style sinter blend containing iron ore concentrates. The operating conditions of the two granulation drums (laboratory and commercial scale) were fixed at the same Froude Number (0.00337), space factor (15 per cent) and residence time (4.5 mins). The granules were characterised by measuring their mean size, size distribution and green bed voidage. It was found that the laboratory scale granules were representative of commercial sinter plant granules at similar moisture content. When the moisture was fixed at ~6.9 per cent, granulation time had no significant effect. A further fundamental investigation was undertaken to measure the water holding capacity and intra-particle porosity of the individual ores used in this study. The kinetics of water absorption were measured which showed that water absorbs quickly into the ore particles within the first 60 seconds, slowing down until final saturation was attained after six hours. A linear relationship between the water holding capacity and intra-particle porosity was noted for different ore particle sizes. The results of this study provide a baseline understanding of the current commercial sinter blend and encourage exploring the specific effect of increasing the proportion of ultrafine concentrates in sintering in a future study.

Sep 18, 2023

By Wymer DG

The concept of hydro power in deep mines is based on the exploitation of the hydrostatic head that can be gained as refrigerated cooling water descends in shaft pipe columns from the surface, to provide hydraulic power for machines at the working face. This paper describes the work done on two important aspects of the controlled distribu-tion of the high pressure water within a mine, namely the control of pressure under normal operating conditions, and the control of flow in an emergency situation following a pipe breakage. Suitable methods of control have been determined using theoretical techniques to model the steady and unsteady flow behaviour of the water in the pipeline, and taking into consideration the environmental constraints on the types of control devices that can be used. The preferred approach is one in which the high pressure water itself is used as the control medium. The control valves themselves can be fairly conventional in design, but in the case of pipe break protection it is shown that a less conventional approach based on the use of a hydraulic fuse gives improved control performance.

Jan 1, 1985

The population and the per capila consumption of mineral resources have both grown dramatically during the century past. It is argued that growth will continue through the century ahead but that the magnitudes of undiscovered resources are probably adequate to meet demands. The challenge that the mineral explorer of the future will face is finding deposits beneath several kilometres of barren rock.It is further argued that the principal challenge that society will face in the century ahead is the amelioration of environmental stress.

Jan 1, 1993

By Kazis JV

The beneficiation of fine coal has been the major problem facing the coal preparation engineer in recent years. The influence of clay slime, particle size and reagent type are but a few of the many factors that affect the recovery of fine coal. Laboratory test work has indicated that substantial increases in recovery could be achieved by improvements in technology in all these areas. Unfortunately, in most cases this technology has not carried through to the operating plants.

Jan 1, 1984

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By Huntington J. F, Green A. A

The quality of a photointerpreter's anno- tation of an image may be displayed by writing maps in which the pixels are shaded according to the number of times a pixel was seen to be on a feature. The map of grey tones is more valuable, if, for each grey level, a measure of quality is determined, which is the probability that a feature exists in a pixel of a given grey tone. From repeated annotations (at least four) of the same image by a single observer, it is possible to formulate a perception model which describes stochastic processes in the observer. From that model, it is possible to assign estimates of data quality for each observer to each grey tone. For two observers on the same scene, the 'mean' method of quantifying the grey levels is to assign a value equal to the mean of the ii,:lities for each of the two observers separately. For this example, the grey tones arr thus quantified at probability levels of 0.70, 0.80, 0.90 and 0.95.

Jan 1, 1977