Search Documents

By Noller B. N, McGill R. A

The Alligator Rivers Region has been the scene of one of Australia's most intensive environmental monitoring efforts since the current generation of uranium mining was mooted in the 1970s. Prior to mining, the local environment and the nature of potential impacts were not well known. The initial monitoring programs therefore included large baseline characterisation and research components. After some 15 years, water, soil and sediment monitoring programs have been reduced to a fraction of their early size, as the mining and natural systems became better known and characterised, and the actual nature of the environmental impacts were established. Modem techniques allow much more rapid and thorough identification of chemical species and elements of concern, allowing much more focused monitoring programs to be designed. In the 1980s data collection was emphasised at the expense of interpretation, and monitoring programs were maintained at much higher levels than were in fact required. It is now clear that investigations are important and should be distinguished from monitoring programs, and that the timely interpretation of investigations and implementation of recommendations can greatly reduce the effort and expense that can be involved in a monitoring program. Monitoring programs based on a sound understanding of potential environmental impact may then be efficient and cost-effective, yet provide sufficient information to assess the environmental impact of mining, guide further environmental protection measures when problems are detected, and demonstrate compliance with regulatory requirements.

Jan 1, 1994

By J A. Sanchidrián

The general ranges of validity of some distribution functions are assessed from their behaviour with 119 sets of fragmentation data from bench blasting obtained by sieving. The emphasis is on determining the lower size/passing limit that the size-scaled Rosin-Rammler, Grady and Swebrec functions, and their bi-component versions, can represent with reasonable precision. By fitting these functions to the data using different weights, the accuracy of the fit varies in the different size/passing zones, so that an overall knowledge of the capacity of the function is obtained across the whole size range, from the coarse zone to the fines. Reasonable ranges of use of bimodal Rosin-Rammler and extended Swebrec (all of them five-parameter, bi-component distributions) are, in terms of percentage passing p, 99 > p > 2 per cent (up to 100 per cent for the extended Swebrec), or 90 > p > 0.5 per cent, in which the expected error of the calculated size is below 15 per cent in the extremes of the range, and less than five per cent in most of the central range; maximum errors (ie errors that will only rarely be exceeded) are typically less than 50 per cent in the central range, and up to about 100 per cent in the extremes. Ranges of use for the Swebrec and the size-scaled Rosin-Rammler (three-parameter distributions), with only slightly larger errors than the bi-components, are 100 > p > 5 per cent or 80 > p > 2 per cent. The classical two-parameter Rosin-Rammler can be used in the range 95 > p > 20 per cent or 90 > p > 10 per cent, with expected and maximum errors less than about 15 per cent and 100 per cent respectively.CITATION:Sanchidrián, J A, 2015. Ranges of validity of some distribution functions for blast-fragmented rock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 741–748 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By J Brisebois

The Wisemans Creek derelict mine site is located in native forest approximately 150 km west of Sydney. Mean annual rainfall at Bathurst, 20 km to the north, is 634 mm and reasonably distributed throughout the year, with slightly more rain falling in the summer months. Evaporation is 1350 mm per annum and considerably exceeds rainfall in all but the winter months (May to August). This results in a water deficit for much of the year. Groundwater is relatively deep, as it has not been intercepted in the shallow open cut workings. Investigation of the groundwater regime was beyond the scope of the current study. Mining has taken place on the site for almost 100 years, during which copper, talc and gold have been sequentially extracted from surface and shallow underground workings. The site is now characterised by the presence of small open pits, unprotected shafts and adits, mullock heaps and an unconfined tailing deposit from a small cyanidation plant. From a distance, the mine area is visible because of two distinct steep bare slopes below the relatively small mine workings and mullock heaps. The mining area was characterised in terms of its environmental, safety and heritage issues. Mullock from the early copper mining was found to be acid forming and leachate from this, combined with clearing of timber, has most likely resulted in death of vegetation below the heaps. The mullock also contains elevated concentrations of heavy metals. The gold tailing is apparently benign and not acid forming, although there are indications of oxidation and acid formation in the derelict gold open cut. Oxidation of the acid forming mullock still appears to be taking place even after being exposed to the atmosphere for at least 50 years, resulting in continued contamination of the slopes below the heaps with heavy metals. The concentrations of metals decreases with distance below the mullock heaps and also is confined to the ground surface the further away from the mullock, providing further evidence to support the theory that the mullock is the source of contamination. Despite this continuing contamination, its spread beyond the immediate mining area appears to have been limited because of the relatively dry climate, with only intermittent rainfall and stream flows. Irregular storm flows in the nearby creek could also have washed any contaminated soil some distance from the site and beyond the area investigated in this study. Remediation of the site and restoration of vegetation on the bare slopes will therefore depend on elimination of the source of acid and metals. Options for remediation, focussing on minimising cost by retaining the materials on or close to the site, are identified. The volume of the open cuts would appear to be close to that required for burial of the acid-forming mullock, thereby removing the source of surface contamination while keeping it above the groundwater table. However, implementation of this remediation plan will depend on the availability of funds to undertake the work through the New South Wales GovernmentÆs Derelict Mines Program.

Jan 1, 2003

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

This presentation addresses the sources and weighting of project risk in coarse gold deposits with relevance to experiences at the Ballarat mine and Castlemaine goldfield. With sample representation and reliability often a source of great error in the resource estimation of coarse gold deposits, it follows that this matter should be of greatest risk to a mining project - but is it? What are the costs and efforts required to best quantify the sampling error due to nuggetty effect? After all, the main problem in Victorian gold mining ventures in the current decade is not the amount of gold available, but defi ning which portion of it can be converted to Ore Reserves or more so profitable gold bars. The author postulates that greater risk to the project lies in the geological interpretation and matching resource spatial parameters to mining methods, than the degree of uncertainty related to grade due to nuggetty gold. Recent experience in the Victorian goldfi elds is that the investor market has already severely discounted Mineral Resources reported in accordance with The JORC Code - so if they don't believe in the capacity to upgrade the resource why should we? To this end, Castlemaine Goldfi elds Ltd at its Ballarat gold project does not intend to estimate its gold mineralisation for public release, instead choosing to focus on the geological interpretation and mine planning elements. So with coarse gold deposits, is your Mineral Resource reported with The JORC Code a glass half full or half empty? Our mining forefathers in Victoria had no predictive tools which could define resources to any degree and yet were successful. By over emphasis on the definition of mineral resources and particularly the sampling error, are we ignoring the basics of cost control, solid geological interpretations and maximum mining flexibility. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By Casley G. E, Pritchard J

A single slurry fed fluosolids roaster was chosen to replace six multiple hearth roasters in the Copper Smelter at Mount Isa as part of the overall program to increase production from 100 000 to 155 000 tonnes blister copper per annum. The paper describes factors influencing the choice of the unit, problems encountered during the commissioning and details of the present roaster operation.

Jan 1, 1974

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By B J. Monaghan, R J. Longbottom, S Prabowo, D Del Puerto, B Maisuria, C W. Bumby

The use of hydrogen as a reducing agent can substantially reduce carbon dioxide (CO2) emissions from the ironmaking process. Iron ore fines can be reduced in a fluidised bed (FB) using hydrogen (H2) at high temperatures (>800°C), although several studies have reported the sticking of particles which causes the bed to defluidise, effectively shutting down the process. Here, we report results from the reduction of New Zealand (NZ) titanomagnetite (TTM) ironsands in a small-scale laboratory FB (100 g) at temperatures between 800–1000°C using H2 flow rates up to 5 standard L/min. No sticking phenomena are observed under any of these conditions, which is attributed to the formation of a stable titanium-bearing oxide layer on each particle’s exterior, preventing iron-iron contact at the particle surfaces. Pre-oxidised NZ TTM ironsands have also been studied and shown not to stick. Interestingly, at lower reaction temperatures the reduction kinetics for pre-oxidised ironsands is faster than for as-received ironsands. This increased kinetic rate can be attributed to the preoxidation stage inducing micro-fractures that create a void for the hydrogen to diffuse into the inner regions of the particle. In addition, oxidation of TTM appears to segregate the particle into two distinct phases, a high Aluminium-Magnesium (Al-Mg) phase and a high Titanium (Ti) phase. The findings are important as increasing the operating temperature of the FB reactor results in a faster reaction rate and higher gas utilisation, making the process more economically attractive. Furthermore, oxidation of NZ TTM ironsands results in a faster reduction rate at lower temperatures (800°C– 900°C) opening the opportunity to reduce the reaction temperature which might be beneficial in a final commercial-scale process.

Sep 18, 2023

By Stevak D, Plesingerova B, Ellias K, Tkacova K

This paper presents information on the processing of minerals by decrepitation that can be an integral part of their mineral dressing. In the case of carbonates, processing by decrepitation is a special operation that has its objective as concentration of the oxide. Selective fragmentation of magnesite brought about by decrepitation uses pseudomorphosis which was observed at thermal decomposition of carbonates. By decrepitation of magnesite high-grade MgO concentrates were obtained with MgO contents above 80 per cent. With the sideritic ores a very important phenomenon was observed consisting in the removal of quartz in the fragmented fine-grained product which favourably affect pelletisation of the fines. The selective concentration of the MgO product brought about by thermal decomposition of dolomite accompanied with decrepitation was negligible.

Jan 1, 1993

Teleoperation is one method by which an operator can remotely control and monitor a vehicle. The operator monitors the status and progress of the remote vehicle by watching the video transmitted from one or more cameras which are mounted on the vehicle. In the case of an LHD, it will be fitted with three cameras. For a twin-boom Jumbo, four cameras are mounted on the drill, three of which will have remote pan, tilt, 15x zoom, focus and lens cleaning controls. The advantage of teleoperation is that an operator can stand in the drive and send the remote vehicle around a corner, completely out of sight and still clearly see what is happening. This means that an LHD returns with a full bucket and a Jumbo can be operated from a safe distance. Standing in the drive teleoperating vehicles, exposes the operator to passing traffic including the remote vehicle. There are two solutions to this problem. One is to equip the operator with a Nautilus æBuddyÆ jacket which will help to protect them from all vehicles. The other is to move the operator into a safe room or area, away from the fumes, the noise and the traffic. In this comfortable, less stressful environment, the operator will be more productive and less likely to accidentally damage the vehicle. The operatorÆs æsafeÆ room does not have to be a formal control room, it can be any area which has AC or DC power available and is large enough to contain a chair and a 1.5 m x 0.75 m table. The æsafeÆ room can be on the surface or underground, it does not matter to the operation of the Nautilus Equipment. If the LHDÆs, trucks, locomotives, etc are automatically guided from origin to destination, the operator is free to operate several vehicles at a time, performing only those tasks which are too difficult for a computer to do by itself.

Jan 1, 1998

By M I. Pownceby, A Guiraud, S Purohit

Sticking and breakage of iron ore pellets during high temperature reduction can result in several operational challenges during shaft furnace ironmaking. With the shift to H2-based DRI processes and decreasing iron ore quality, this issue becomes more prominent. It is therefore important to understand how the iron ore chemistry and mineralogy affects the sticking and breakage of pellets inside the shaft furnace. This study provides a review of the mechanisms that lead to sticking and breakage of pellets inside the shaft furnace. The sticking index of pellets is related to the rate of metallic iron production as well as the precipitation morphology of product iron. Sticking of pellets is also enhanced by the formation of low-melting slag phases. The breakage of pellets inside the shaft furnace is often associated with the mechanical load of burden and pellet swelling, which is caused due to iron whisker or protruded iron formation. This paper investigates how the composition of iron ore, particularly the presence of different impurity oxides such as SiO2, Al2O3, MgO, CaO and alkali oxides in the pellets, influences the sticking and swelling indices. The effect of ore mineralogy on these adverse behaviours is also discussed.

Sep 18, 2023

The purpose of this paper is to look at the costs of tailings disposal, and in particular the comparative costs of different disposal methods in different situations. Costs are often the hidden design parameter. We know that they are important but sometimes feel that it is not very respectable to talk about them in public. It is better from a public relations point of view for it to appear that the decision-making process is driven by environmental factors or best practice rather than looking for the cheapest option. But this presumes that the two are mutually exclusive and this need not be so. These issues are discussed later in the paper. It is also commonplace for the scale of the mining operation to change with time, typically involving increased throughput rates and total tonnage. New ideas in tailings disposal make their appearance. The regulatory attitude can change. Having made a decision about the disposal method at the time of original feasibility study and design it is easy to suppose that the mine is æstuck with itÆ. But that also need not necessarily be so. Careful costing of options may reveal that a switch in method could be cheaper in the long run. The designer will often tend to think in terms of initial earthworks and site development costs. Aspects of power consumption, labour, and periodic campaigns to move tailings pipelines and carry out embankment raises are either overlooked or not given the same emphasis. This can distort the evaluation process. It is productive to think in terms of dollars or cents per tonne as a basis of comparison, not just the total sums. Tailings disposal can cost from as little as 10 - 20 ó/t to over $1.00/t which is a big range. There may be good and unavoidable reasons for the high figure but there would need to be to justify being so far over the industry average. At the same time, mining and processing costs, at least for gold, are around $15 - 20/t. Viewed from this perspective tailings disposal will always be a relatively small component of the annual budget.

Jan 1, 2000

By P J. Terbrugge

The concept of vertical pit mining has been developed as an alternative mining method for the exploitation from surface of small, vertical or near-vertical, massive orebodies down to depths of some 200 m, where ore extraction from conventional open pit excavations is rendered uneconomic due to high associated waste:ore mining ratio. Systematic lateral support maintains vertical pit sides, thereby minimising waste mining volumes. Stability analysis techniques have been developed for design of this lateral support, with the support quantum, primarily comprising long cable anchors, dependent upon country rock strength characteristics and pit configuration. Where the cost of support is less than the cost of the comparable conventional pit waste excavation, vertical pit mining becomes an economically viable alternative, additionally providing the benefit of reduced environmental impact and rehabilitation requirements for the mining area. The technique has been successfully applied for the mining of a chrome deposit in Zimbabwe to an 80 m depth, believed to be unique in the world, and a full feasibilty study for a 3000 m2 diamond pipe has been carried out for mining to 200 m depth.

Jan 1, 2000

By M Johnson, M Horrigan

The scope of this report is to examine the aforementioned hypothesis by performing a detailed analytical comparison of a P&H electric rope shovel to an O&K diesel powered hydraulic excavator. In order to complement the integrity of the concluding results, two different size categories will be analysed in order to demonstrate that the findings can be extrapolated and applied to all the machinesÆ size classes. These two size classes are categorised by their bucket sizes and they are in the range of 43 - 58 cubic metres and 23 - 26 cubic metres. It should be noted that electric powered hydraulic excavators will not be considered in this report. In order to compare the electric and hydraulic types, the machine variants that will be analysed are commercial cost-effectiveness and operational flexibility. Although operational flexibility can be an ambiguous characteristic, a clear and thorough definition describing its exact meaning has been included. In order to simplify this study, all the data collected for this comparison have been for overburden removal, eliminating the variation that occurs with the movements of the shovel when selectively mining in the ore deposit. Thus, it ensures that all the data that is compared stems from a common origin for all the shovels. In other words the information will be compared when digging in the same material, loading into the same sized haul trucks, and when possible, with the same operators. Theoretical data received form the respective manufacturers, and actual data obtained from Mount Whaleback, was used for this comparison. This leads to the final comparison, where the operational flexibility and the cost-effectiveness are evaluated, with respect to their individual importance, ultimately influencing the final recommendation.

Jan 1, 2002

In 1939 Dr Neil George gave us the statement: Safety is a state of mind by which men are constantly made aware of the possibility of injury at all times. Is this statement still relevant? Have we been able to capture the essence of Dr GeorgeÆs statement in our current safety management systems and have we been able to capture the lessons from the past? Drawing upon 25 years of experience in the mining industry we explore what was done in the past, how this related to Dr GeorgeÆs statement and how the industry has progressed to the current safety management systems. We review the safety management system used by Roche Mining and demonstrate how it has improved safety outcomes for Roche. We then look to the future û are there new challenges? Are the current management systems equipped to cater for these new challenges and deliver continued improvement in safety outcomes? There will always be a desire to improve the industryÆs safety outcomes and so how are future generations going to achieve the improvement in safety outcomes?

Jan 1, 2007

The Key Issues - An Overview Minerals industry needs Mining companies want technologies which are ò cost-effective, ò high likelihood of delivery (ie transfer existing technologies from other industries), ò highly useable, ò an evolutionary rather than revolutionary approach, and ò to be developed in partnership with the mine, supply groups and researchers, For example, `soft' systems for information collection to better manage the mining process rather than mechanical systems.

Jan 1, 1997

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994