Search Documents

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Z Chang, S A. Mrozek

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Antamina, Peru is the largest Cu-Zn skarn deposit in the world. Skarn mineralisation is focused around a multiphase Miocene intrusive complex comprising at least eight distinct phases identified by cross-cutting relationships, including truncated veins, xenoliths and chilled margins. Skarn alteration and mineralisation, as observed in drill core, remain open at depths exceeding 2.2 vertical kilometres.Porphyry intrusions occur as four major phases with subphases (from oldest to youngest): P1 (a, b), P2 (a, b), P3 (a, b) and two dykes of uncertain timing named Oscarina-1 and Oscarina-2. P1a is a hornblende-biotite quartz diorite porphyry with pervasive K-alteration, local endoskarn and 30–40 per cent sheeted quartz veins, all of which obscure original igneous textures. P1b dacite porphyry is a minor unit with <10 per cent phenocrysts and <3 per cent quartz veins. P1b cuts P1a; P2 dykes cut both units. P2a porphyritic biotite quartz monzonite contains K-feldspar megacrysts up to 4 cm long, local K-alteration and 2–80 per cent quartz stockwork veins. P2b biotite monzonite porphyry contains approximately 50 per cent phenocrysts and typically <10 per cent quartz veins. P3a (brown groundmass porphyry) and P3b (coarse phenocryst porphyry) are minor in volume and extent, and both cut P2 bodies. Oscarina dykes comprise two separate but parallel bodies. Oscarina-1 is a feldspar-phyric rhyolite porphyry, while Oscarina-2 is an intensely chloritised andesite porphyry. Oscarina-1 has a U-Pb (laser ablation inductively coupled mass spectrometry (LA-ICP-MS)) age of 10.1 ± 0.1 Ma, whereas P2 U-Pb zircon ages (LA-ICP-MS) range from 10.0 ± 0.2 Ma to 9.9 ± 0.3 Ma.All the intrusive phases contain quartz veins, with P1a and P2a having the most intensive K-alteration and most abundant quartz veins ± endoskarns. Each phase may have contributed to mineralisation at the right depths and within favourable wall rocks (ie marble) during uplift of the Antamina structural block. Therefore, a model of multiple intrusions during continuous uplift explains the vertically extensive (>2.2 km) skarn and mineralisation at Antamina.CITATION:Mrozek, S A, Chang, Z and Meinert, L D, 2015. A model for the intrusive sequence and Cu-Zn skarn formation at the Antamina deposit, Peru , in Proceedings PACRIM 2015 Congress, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K A. Campbell, K A. Rodgers

The Plumduff sinter occurs at Whenuaroa, near Puhipuhi, approximately 30 km north of Whangarei. It is one of three residual sinters in the southern portion of a mid- to late-Pliocene geothermal system. The deposit consists of many large sinter breccia boulders, including rudrocks (coarse breccias), scattered around the flanks and summit of the small conical hill of Plumduff. Three types of sinter breccia occur: (i) rudrocks consisting of large, angular to sub-angular clasts of layered sinter up to 0.8 m across, as well as smaller clasts of sinter (20 - 100 mm dia), and fragments of stromatolitic structures; all clasts are supported in a matrix of microcrystalline, transparent to translucent to milky quartz; (ii) fragments of layered angular to irregularly mottled sinter of white to grey or bluish hue supported in a translucent to opaque silica matrix; (iii) smaller, matrix-supported breccias with clasts both partially surrounded and/or penetrated, by a clay-like weathering rind, and sinter conglomerates with rounded to oblate clasts. Three principal types of fabrics constitute the bulk of the sinter: (i) stromatolites, including columnar, palisade and filamentous networks, showing progressive silicification, in fenestral, tufted to clotted fabrics; (ii) peloids and pisoids; (iii) plant-rich facies in which various silicified plant species occur in a silica matrix. All fabrics have counterparts in hot spring deposits in the Taupo Volcanic Zone formed at temperatures from 75¦C to 35¦C. Also present is steam-condensate-produced alteration: kaolinite and alunite as well as boulders of quartz lattice texture. Cinnabar only occurs in sinter on the north and south central slopes of the hillside. No quartz veins or geyserite were recognised.

Jan 1, 2001

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

The profitability of gold placer mining operations is determined by more factors than many placer miners recognise until too late. This study is based upon field trips to examine the efficiency of mining and transportation of gravels to a wash plant by bulldozer and truck. At the examined open pit mining operations gravels were washed using water canons, derockers or scrubber trommels. The objective of this study was to determine the relationship between unit costs and power requirements for gravel mining and processing. The author conducted a number of time and motion studies at four open pit gold mines, including the Maly Patom Creek, the Nizhny Patom, the Taimendra Creek and the Kadali-Makit in the Bodaibo District, Irkutsk Region and collected and processed field data. As a part of the study significant correlations were determined and empiric regression equations derived between: power requirements (Ep) and unit cost (Cp) for gravel processing; and total power requirements (Et) and total unit cost (Ct) for gravel mining, transportation and processing. Based on the results of the study it was proposed to modify the current mining procedure methods and to replace water cannons at the Maly Patom Creek with a PPM-5 derocker. Introduction of the proposed technology resulted in 2004 in US$385 000 mining cost reduction at the Maly Patom Creek over a short-time Siberian mining season.

Jan 1, 2007

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

Regions with extensive reserves of brown coal but with inadequate deposits of hard coal provide a particularly suitable field for the application of brown coal petrology.In fact, this discipline is indispensable where brown coal is to form the basis for high-quality products of upgrading. Both chemical and physical analyses are required in addition to the techniques employed in coal petrology, but it is the macropetrographic and the microscopic investigations that are of decisive and specific importance.Foremost among the methods of upgrading brown coal is briquetting. From the raw materials aspect the biochemical rank of coal (i.e. the type of deposit) and the coal variety (i.e. the lithotype) exert a marked influence on briquette strength. These are also the significant factors in the suitability of a brown coal for high temperature carbonization; here the demands on coal quality are even more exacting if adequately sintered and therefore high-strength lump chars are to be obtained. The principle applies also to the char from low temperature carbonization. There are close relationships between the tar yield and the remission of the coal.The reflectivity measurement therefore provides a rapid method for evaluating the suitability of a brown coal for low temperature carbonization. Similar correlations have been established between the content of extraction bitumen (raw montan wax) and the remission. Petrological investigations show that the quality of the coal bitumen is a function of the type of deposit and of the lithotype.

Jan 1, 1968

By Wilson G. L, Lord J. H

A detailed analysis of faulting indicatcs that blocks of "greenstone" have been thrust beneath the southern end of the Mt. Isa orebodies.This "greenstone" basement is considered to be a major structural control in the localization of these orebodies.INTRODUCTIONThis paper is based on exploration carried out by Mining Corporation (Aust.) N.L. from 1956 to 1960 in the area immediately south of Mt. Isa, Queensland. During this period over 20,000 ft of diamond drilling was completed together with costeaning and geochemical exploration.Early in 1959, it became apparent that diamond drill information could not be correlated with the current geological concepts of this area and a detailed geological appraisal became necessary. In all, sixty square miles were mapped at a scale of 1 in. to 500 ft, using enlarged aerial photographs. All drill core was logged and sections re-interpreted.Professor K. C. Dunham of the University of Durham consulted on this project and contributed through valuable discussion. Dr. A. Day of the University of Sydney carried out a gravity survey in February 1960 and Dr. H. Wilshire of the same University undertook microscopic examination of rocks from the area. Certain sections of the area were investigated geochemically by Mr. K. K. Hughes of New Consolidated Gold Fields (Asia) Pty. Limited in 1960.In outlining a theory of ore genesis in the area the writers have drawn heavily on the invaluable data published by many previous workers on the Mt. Isa field, in particular...

Jan 1, 1963

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Driver R. C, Moelle K. H R

This paper is dedicated to the memory of our friend Peter McKenzie who contributed much to the knowledge of the New South Wales Coalfields.ABSTRACTA fossil river system was recently mapped over parts of the Southern Coalfield, N.S.W. This river system occurs in the roof strata of the Bulli Seam. Sandstone of a fluvial nature was deposited in its course. The sandstone exhibits strong sedimentary vectorial properties and has a marked influence on strata-control in colliery workings.The sedimentary features analysed indicate an approximate S200W flow direction. Petrological studies reveal a clastic, well-cemented sedimentologically and structurally anistropic rock type. Washouts have been found and isopach maps of both sandstone and underlying roof-strata have been compiled. Relevant measurements were carried out in existing colliery workings and on bore cores.Optical determinations of feldspars revealed the presence of plagiocIase feldspars with few exceptions. Most of the feldspars are altered to clay minerals. It was found that a geographical trend exists in the distribution of feldspars, with more basic plagioclase in the northern part of the field.The source area of the fluvial sandstone lies to the north of the Southern Coalfield.Petrofabric analyses were done on several specimens of the fluvial sandstone. In the vicinity of major disturbances, penetrative fabrics were discovered.Calcites (e, 0112), micas (001), and quartz (crystalIo graphic c) show preferred orientations.

Jan 1, 1967

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

Cook Colliery currently mines in the Argo Seam, beneath old workings in an overlying seam. The Argo seam is up to 4.8 m thick and a continuous haulage system behind an ABM25 is used to develop first workings. Current partial secondary extraction utilises floor stripping and pocketing or sumping first working pillars on retreat. The following paper summarises this recent secondary extraction experience, particularly from a geotechnical perspective, but also considering production and ventilation issues. Outcomes and learnings are presented for mining in this challenging and close multi-seam environment. The sealed castor seam workings are within 20 m, and vary from unmined areas to large first working pillars, to partial extraction panels and full extraction panels. High stress remnant pillars and goaf-edges are notable mining considerations. The mining environment is further complicated by faulting, thrust zones and weak laminated roof.

Nov 25, 2010