Search Documents

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By S. C. Schaeker, A. W. Schlechten, A. H. Larson

PARRAVANO and Malquori' studied the equilibrium of H2S-Hz with molybdenum and its lowest sulfide which they believed to be MoS2. Mc Cabe' has shown that its composition is actually Mo2S3 and determined its dissociation pressure by means of Knud-sen effusion measurements. Stubbles and Richard- son3 have recently studied the equilibrium of gas mixtures of H2S-HZ with the two-phase solid mixtures of Mo-MozS3 and Mo2S3-MoS2. The latter investigators found that M02s3 deviated slightly from the stoichiometric composition, but they did not determine the homogeneous region of the disulfide phase. Morimoto and Kullerud, studied the Mo-S system by quenching, microscope, and X-ray methods and concluded that the disulfide is stoichiometric. The present investigation was concerned with the measurement of the sulfur vapor pressure variation with composition at 1100°C in the homogeneous region of "MoS2". These measurements were made by reacting: 1) molybdenum powder (99.97 pct Moj with sulfur vapor, and 2) MoS1.g9 (formed by reaction of Mo + H2S) with sulfur vapor in a quartz capsule. Conditions were controlled to form an equilibrated phase within the homogeneous region of the disulfide. The quartz capsule was sealed off initially under a vacuum and the residual gases were gettered by titanium powder contained in one end of the capsule. A mixture of Mo + S or MOS,., + S was in the other end. The section containing the titanium powder was heated for 24 hr at 700°C and then removed by flame sealing. The end of the capsule containing the charge was then heated to 1100°C. The other end of the capsule was maintained at a temperature which would produce the desired sulfur pressure in the capsule (liquid sulfur distilled from the charge mixture was retained in this end). After equilibration, the capsule was removed from the heating assembly and rapidly air-cooled. It is assumed that equality existed between the total sulfur pressures (PT) in the two ends of the capsule and not between the partial pressures of the different molecular species (S, SZ, Three separately controlled heating elements were used to maintain the proper temperature gradient over the length (approximately 12 in.) of the capsule. A thermocouple-Wheelco "Capacitrol" system was used for temperature control of the two end heating elements within 2"C. The center heating element was controlled directly by a " Power -stat". Separate controlling and measuring thermocouples were used for both end heating elements. Pt-Pt(l0 pct Rh) thermocouples were used for 1100°C and Chromel-Alumel thermocouples were used for lower-temperature control and measurement of the assembly. Silver foil was wrapped around the end of the capsule containing the liquid sulfur to insure a constant temperature zone. The thermal gradient over the entire length of the capsule was measured to: 1) ascertain that the length of the constant temperature zone of the liquid-sulfur end and the sulfide end was sufficient, and 2) ascertain that the liquid-sulfur zone was the zone of lowest temperature. The data obtained in this investigation are shown in Fig. 1 and Table I. The total sulfur pressure (PT) and p(S2) were calculated from the data of Braune et UZ.~ The compositions of the equilibrated disul-

Jan 1, 1964

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954

By A. F. Crawley

THIS paper describes part of a series of density measurements on low melting point metals being undertaken at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This program has received support from the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Examples of the type of work being done have already been given in earlier papers' , which deal with the densities of lead, tin, and some of their alloys. Densities were measured using a graphite pyc-nometer by a technique which has already been described." The cadmium and indium, supplied by the Consolidated Mining and Smelting Co. of Canada were of 99.999 pct purity. Density determinations on indium, as for lead and tin,1,2 were made under a vacuum of about 5 x 10-6 torr because the oxidation and vaporization characteristics of the metal do not create experimental difficulties. This contrasts markedly with cadmium which, even at the relatively low temperatures of our experiments, has a high vapor pressure and a strong oxidation potential. To suppress the harmful effects of these properties, determinations on cadmium were made with success under an atmosphere of argon, the technique having been previously established in this laboratory for measurements on zinc.3 The densities of cadmium and indium are listed in Table I and plotted in Figs. 1 and 2. From the graphs, it is readily observed that the densities of both metals vary linearly with temperature. This relationship expressed mathematically is of the form:

Jan 1, 1969

For the year ending February, 1917 PRESIDENT ................... L. D. RICKETTS,' NEW YORK, N. Y. . PAST PRESIDENTS BENJAMIN B. THAYER 1 NEW YORK, N. Y. ................. WILLIAM L. SAUNDER2, NEW YORK, N. Y. FIRST VICE-PRESIDENT ................ SIDNEY-J. JENNINGS,1 NEW YORK, N. Y. TREASURER ................ GEORGE C. STONE,l. NEW YORK, N. Y. . SECRETARY EMERITUS ................ ROSSITER W. RAYMOND, NEW YORK, N. Y . SECRETARY ............... BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 8, 1916

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 9, Article I, of the Bylaws of the Institute (see page 61 and following pages). During 1934, sundry amendments were made for the purpose of improving

Jan 1, 1939

By J. Gordon Parr, M. J. Bibby

In addition to the (bcc) - (cph) transformation at 882°C a second distinct change of slope has been observed on a titanium cooling curve between 905" and 960°C.1,4 Duwez,1 commenting on work by McQuillan,2-4 attributed this arrest to contamination of the specimen with oxygen—a possibility that existed even at the reduced pressure of 10-5 mm Hg at which the experiments were conducted.

Jan 1, 1963

By G. F. Bolling

HE high mobility of grain boundaries in zone-refined metals has been particularly demonstrated for lead above 150°C in grain growth studies1 and in the extensive work by Aust and Rutter.1 In these investigations, no elaborate precautions were taken to eliminate oxygen from the zone-refined lead; however the alteration of creep characteristics by oxygen concentrations of less than 5 x 10 -5 wt pet

Jan 1, 1962

By E. C. Burke

IN view of rather widespread use of calcium as an alloying addition to magnesium alloys, it is rather surprising to find that, although the general features of the Mg-Ca equilibrium diagram are known with a fair degree of certainty,' ," considerable ambiguity concerning the solid solubility of calcium in magnesium exists. By using the disappearing phase technique in a metallographic study, Haughton' found that 0.6 pct Ca was soluble at 300°C and 1.8 pct was soluble at 516°C, the eutectic temperature

Jan 1, 1956

By A. D. K. Laird, John A. Putnam

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By John A. Putnam, A. D. K. Laird

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By W. F. McDermott

This is the dawning of the computer age in process control. As 1968 drew to a close, many plants had computer installations which were being used for logging, monitoring and reporting. Today, computer usage is given serious consideration before the construction of any major minerals processing plant. Unitized automatic control of individual processes is abundant. Many plants are considering closing these control loops, i.e., allowing the computer to direct the operation of the controllers (Digital Analog Control-DAC). The next step is to make the computer itself the controller (Direct Digital Control-DDC)1 Perhaps the most important future use of computers will be in controlling interrelated operations and control units. Progress along these lines depends on the steadily improving capabilities in the field of mathematical modeling.

Jan 1, 1970

State Mine Experiment Station, College of Engineering, University of Alabama, University, Ala Copies of two bulletins issued by the Mine Experiment Station may be had by writing to the Director of the School of Mmes at the above address: Bulletin 1, Coal losses in Alabama, 2, A specific gravity study of Alabama coals The Cooperative work of the Mine Experiment Station with the Southern Experiment Station of the U S Bureau of Mmes is covered by Bulletins of the U S Bureau of Mines

Jan 1, 1933

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

The rate of scale fot'~I~ti0n on tantalum held in H20-Hz-Ar gns mixtures at temperatures between 840" and 1250°C is related to gas composition and ternpevature. It is found that water vapor partial pressure determines the oxidation rate at a given temperature and that the oxygen potential as fixed by the water vapor to hydrogen ratio Ins no significant effect on the oxidation rate. The Ta205 scale formed during oxidation is composed of an inner lattice-dijf~ision barrier and an outer layer of- cracked/porous oxide 1 HE oxidation of tantalum at temperatures less than 800°C is characterized by solution of oxygen into the metal,'-' the formation and growth of suboxides into the metal,')2~10-15 and the delayed nucleation of the highest oxide, Above 800°C, Ta205 is found to nucleate rapidly10, 11, 15, 16 except at low oxygen pressures:15 however, there is uncertainty regarding which does not retard the oxidation process. For each gas con~position and temperature investigated, the oxidatioz rate becomes constant after a short adjustment period. It is shozm that a constant oxidation rate nzay pre~?ail even though the tlzickness of the inner lattice-dijjitsion layer of Ta205 is clanging. TFze initial czcrz!ature of the typical 'Paralinear" oxidation curve may result froprz causes other than an increasing thickness of tlze inner protective layer. the detailed mechanisms of the high-temperature oxidation. Peterson, Fassell, and wadsworth17 observed linear oxidation behavior for tantalum in oxygen at temperatures between 600" and 1000°C. They reported that equilibrium adsorption of 0, occurs on a surface prior to the rate-deter mining step of the reaction. Cowgill and stringer1' confirmed the observations of Peterson and his coworkers. They stated that the rate-determining step of the reaction could be either the incorporation of adsorbed oxygen into the anion lattice or the dissociation of 0, at the gas-oxide interface. The relative rates of the two surface reactions were proposed to be dependent upon the reaction temperature and the oxygen pressure. stringerlo subsequently reported that the reaction surface is located somewhere

Jan 1, 1968

By J. M. Dahl, R. J. Warrick, O. K. Riegger, H. Van Vlack

A liquid which is rich in oxygen (and silicon) develops at steel rolling temperatures in resulfurized and plain-carbon steels. This liquid fluxes solid manganese sulfide. The composition of the liquid and the resulting microstructures vary with the manganese/silicon/oxygen ratios in the steel. The observations and conclusions zuhich are presented are used 1) to suggest a mechanism for MnS deformation in resulfurized steels, and 2) to rationulize hot-shortness anomalies between plain-carbon and resulfurized steels. 1 HIS is a summary of the dependence of sulfide inclusion microstructures upon steel composition, and an interpretation of the behavior of sulfide inclusions at steel-rolling temperatures. Sulfide inclusions are known to have several metallurgical effects upon steel. Their effects upon hot-shortness are best appreciated. Although hot-shortness is well known, it is questionable whether its mechanism is fully understood because there are several anomalies in our interpretation. For example, why should not high sulfur contents produce extensive hot-shortness in free-machining steels ? A second metallurgical consequence of sulfide inclusions appears because sulfide inclusions improve machinability. Furthermore, globular inclu- sions are to be desired over elongated inclusions. To date, we know that lower silicon contents (< 0.010 pct) favor the globular sulfides, but we do not know why this interrelationship between silicon content and inclusion shape exists. Finally, the evidence is strong that the surface quality of a hot-rolled steel is particularly sensitive to the sulfur content. SUMMARY OF PREVIOUS WORK The role of sulfur in hot-shortness was first suggested during the past century. It is uncertain who was the first to conclude that sulfur was less deleterious in the presence of manganese, and that manganese altered the sulfide phase from a liquid FeS to a solid MnS at steel-rolling temperatures. However, Urban and chipman&apos; emphasized that liquid FeS may accumulate as an interdendritic film during solidification. More recently, Keh and Van lack&apos; showed that the intergranular liquid does not completely surround the metal grains at all rolling temperatures. Rather, a small finite dihedral angle exists when geometric equilibration is attained at

Jan 1, 1962

By Lester C. Uren

With the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world&apos;s petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described. Essential Parts of Oil-well Plungeb Pump The pump commonly used in lifting oil from wells in American practice is of the simple displacement type, in which a plunger equipped with a working, or traveling, valoe is given a vertical reciprocating motion in a stationary working barrel. The latter is suspended from the surface by tubing, submerged in the well fluid, and is equipped at its lower end with a stationary standing valve; Figs. 1 and 2 illustrate two common types of oil-well pumps. The simple cup-leather packed plunger of Pig. 1 has its counterpart in the long, hollow, cylindrical, polished steel plunger of Fig. 2; otherwise the two types are identical in the form and arrangement of their essential parts. Fig. 2 shows the additional feature of a "garbutt

Jan 1, 1927

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

By S. J. Kidder

Application of shrinkage stoping methods, without filling, in the mining of large silver-gold orebodies in the Mogollon district, where the ore is hard and wall rocks stand well without timbering and where veins make little water. Vertical and inclined shafts in use with both surface and underground hoisting stations. Storage pockets used on main hoisting levels, with electric signals and telephones for communication. Power is generated by De La Vergne engines having a total sea-level rating of 1540 hp. On account of the remote location of the camp, transportation is an important item of expense, amounting in 1922 to $0.641 per ton of ore milled or $0.265 per ton-mile on all freight hauled. THE Mogollon mining district is in the southwestern part of New Mexico near the southern end of the Mogollon range, from which the district takes its name. The town of Mogollon is but 37 1/2 mi. in an air line northeast of Clifton, Ariz. The air-line distance from Silver City is 52 1/2 mi. and from Tyrone, 57 mi. Supplies are transported by motor truck from Silver City. The distance by road is 75 mi., half of which is an improved highway of modern construction. Transportation has always - been a large item of expense in carrying on operations in the district. Valuable ore is said to have been discovered in the Mogollon Mountains as early as 1870 but the first regular prospecting was carried on in 1875, by James C. Cooney, a sergeant from Fort Bayard. His discovery of rich silver-copper ores in the region of Mineral Creek led to the establishment of the Camp of Cooney. Remote from any settlements where there was a semblance of law and order, and harassed by the Apaches, development was slow and nearly 10 years elapsed before the village of Mogollon was established on Silver Creek. Prospecting in this section of the district had disclosed the outcrops of several promising veins containing silver-gold ores. Among the early claims located were the Last Chance, Top and Confidence, on what has proved to be the most productive vein in the district.

Jan 3, 1924

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960