Search Documents

By C. E. Lundin, M. Hansen, D. J. McPherson

PRIOR work on the Zr-Cu phase diagram by Alli-bone and Sykes,' Pogodin, Shumova, and KUGU cheva,' and Raub and EngeL3 as confined largely to copper-rich alloys. The investigations of Raub and Engel were the most recent and seemingly the most complete of these. Alloys from 0 to 68.3 pct Zr were studied principally by thermal analysis and microscopic examination. These authors reported an inter metallic compound ZrCu, (1116°C melting point) and two eutectics, one at 86.3 pct Cu (977°C mp) and the other at 49 pct Cu (877°C mp). The solubility of zirconium in copper was reported to be less than 0.1 pct at 940°C. The zirconium melting stock consisted of Westing-house "Grade 3" iodide crystal bar (nominally 99.8 pct pure). It was treated by sand blasting and pickling (HF-HNO, solution) to remove the surface film of corrosion product, resulting from grade designation tests. The crystal bar was cold rolled to strip, lightly pickled again, and cut into pieces approximately 1/32 in. thick and 1/4 in. square. These were cleaned in acetone, dried, and stored for charging. The high-purity copper (spectrographic grade) was supplied by the American Smelting and Refining Co. with a nominal purity of 99.99 pct. These copper rods were rolled to strip, cut into squares the same size as the zirconium platelets, cleaned in acetone, dried, and stored. Equipment and Procedures The equipment used for melting and annealing the zirconium binary alloys and for the determination of solidus curves has been described in connection with previous work on the Ti-Si system' and in recent papers in this series describing the studies on eight binary zirconium systems.5-' Techniques employed for preparing and processing the alloys were also similar to those used in the above references. Ingots of 20 g were melted under a protective atmosphere of helium on water-cooled copper blocks in a nonconsumable electrode (tungsten) arc furnace. The ingots were homogenized and cold-worked prior to isothermal annealing to aid in the attainment of equilibrium. The specimens were heat-treated in Vycor bulbs sealed in vacuo or under argon, depending on the temperature of the anneal. Quenching was accomplished by breaking the Vycor bulbs under cold water. Temperature control was within ±3OC of reported temperatures. Thermal analysis was primarily relied on to determine eutectic levels, peritectic levels, and compound melting points. The induction furnace incipient melting technique was also used but did not provide the accuracy obtained by thermal analysis in this system, which involves much lower solidus temperatures than the other zirconium systems. A special technique for the determination of characteristic temperatures was employed in the case of several intermediate phases and their eutectics which displayed very small differences in melting temperatures. Specimens were sealed in Vycor bulbs and annealed at a series of very accurately controlled temperatures. Metallographic examination was then employed to reveal incipient melting. Furnaces and techniques in general were described previously.' The echant used was 20 pct HF plus 20 pct HNO3 in glycerine unless otherwise stated. Results and Discussion The chemical analyses of the majority of alloys prepared for the determination of phase relationships in this system are given in Table I and a brief summary of the equilibrium anneals employed is given in Table 11. In a preliminary program, alloys containing 1, 4, and 7 pct Cu were annealed for three different times at each of the temperatures 700°, 800°, and 900°C. No change in the relative amounts of phases present was detected after 350, 150, and 75 hr at the above temperatures, respectively. The times listed in Table II were accordingly chosen as a result of these preliminary tests. Zirconium-rich alloys containing from 0.1 to 10 pct CU were reduced by cold pressing from 58 to 8 pct, depending upon thk alloy content, homogenized for 7 hr at 900°C, and then reduced 80 to 13 pct by cold rolling, again depending upon copper content. Other alloys were studied in the cast, or cast and annealed conditions. The contracted scope of investigation for this system included the range 0 to 50 atomic pct Cu. This approximate region is shown in Fig. 1. Due to evidence of phase relationships departing considerably from those proposed by Raub and Engel" in the 50 to 100 atomic pct range, the investigation was extended to cover this composition area rather thoroughly also. Fig. 2 is a drawing of the entire diagram. The labeling of some phase fields was omitted in Fig. 2 for the sake of clarity. An expanded view of the zirconium-rich region, with the experimental points necessary for its construction, is given in Fig. 3. The generally accepted value of Vogel and Tonn8 or the allotropic transformation a + 862' ±5OC, was employed in the construction of these diagrams. A careful study revealed that the "Grade 3" crystal bar used in this investigation actually transforms over the approximate range 850" to 870°C, due to impurities. It must be expected that this two-phase field in unalloyed zirconium will cause some departures from binary ideality in the very dilute alloys. Zirconium-rich Alloys: The a + ß transformation temperature is decreased from 862" to about 822°C by increasing amounts of copper. Thus, a eutectoid reaction, fi ß a+ Zr,Cu, occurs at a composition of about 1.6 pct Cu. The eutectoid level was determined to lie between the alloy series annealed at 815" and 830°C. The placement of this eutectoid temperature

Jan 1, 1954

By G. S. Hume

As predicted a year ago, owing to the discovery in 1936 of crude oil on the west flank of the south end of Tuner Valley in the eastern foothills of Alberta, 50 miles southwest of Calgary, and the drilling activity that resulted, the production of crude oil in Canada during 1937 showed a very substantial increase over the previous year. The production from other parts of Canada is relatively small and shows slight variations only from year to year. The production of crude oil in Canada and the production in Alberta, the main producing Province, is shown in Tables 1 and 2.

Jan 1, 1938

By Robert R. Britton

A study conducted at The Ohio State University sought to deter- mine whether explosives break rock primarily employing shock energy or energy stored as borehole gas pressure. The amount of broken material, calculated borehole pressure, and measured stress waves are compared as decoupling ratios (borehole diameter/explosive charge diameter) increased from 1 to 3 and all other variables remained constant. Breakage and calculated borehole pressure displayed a decrease as the decoupling ratio increased while the shock energy remained constant. The strong implication is that borehole gas pressure is the primarary force in breaking rock with explosives.

Jan 1, 1984

By G. T. Hahn

On the basis of the recommendation of Lovell, Vogel, and Wernick,&apos; Fry&apos;s reagent*2 was recently c) if decoration of the dislocations by carbon or nitrogen atoms is a factor in the etch pitting. Experiments were performed with samples of a commercial 1020 steel, a vacuum-melted iron (C - 10 to 15 ppm, 0 - 20 to 50 ppm, N < 2 ppm), both annealed 4 hr at 1100°C, and a zone-refined iron (C - 3 to 5 ppm, 0 - 10 ppm, N < 1 ppm ) in the as-cast condition. Saomple surfaces were prepared by grinding to 600A grit and electropolishing. Initially, effects of etching the steel with modifications of the basic Fry composition were examined. It was found that increasing the alcohol or HC1 concentratior~ retarded dislocation pitting; reducing the acid content promoted secondary pitting. Cooling the reagent and the sample did not improve the quality of the etch pits. Best results were obtained with freshly prepared reagent modified by increasing the CuC12 content to 15 g. This composition was used in subsequent experiments. Annealed samples were etched 10 to 15 sec; cold-worked samples —2 to 5 sec.

Jan 1, 1962

By Ossi E. Palasvirta

The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant* and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawin4 batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure1 was employed, wherein the pulp falls freely through the depolarizing coil.

Jan 5, 1958

By Raymond Dugdale, Fathi Habashi

There has been a recent interest in studying the action of anhydrous sulfur trioxide on ores to convert the metal values into a water-soluble form as a substitute for leaching by sulfuric acid. For example, Svenke1 converted the small amounts of uranium in slate ash into a water-soluble form by treating the material with SO, at about 600°C. Chao and Sun found that a variety of aluminum-bearing minerals could be sulfatized by SO, in the temperature range 400° to 600°C usually in the presence of a catalyst such as sodium sulfate. Kruse3 patented a process for beryllium recovery from the low grade ore in Utah by first reacting it with SO, at 560° to 750°C then leaching the product with water. In the present report, the action of SO, was examined in the temperature region 100°-300°C which was not investigated by those workers. Experimental Tests were conducted on a beryllium ore sample from Utah, the analysis of which is given in Table 1. It corresponds closely to a saponite ore type as given by Crocker et al. It was in powder form 45% passing a 400

Jan 1, 1973

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar&apos;) when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By W. T. Burns

Attempts were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles. The average composition of the furnace charges was as follows: Per Cent. Peer Cent. Copper. Precipitate,..........7.5.3 40 to 80 Purification cathodes,.....1.9 92 Refinery slag (oxide slag),.. 10.1 50 to 60 Electrolytic cathodes,... 2.1 99.9 Precipitate anode scrap,.... 3.1 99.0 Scrap copper,.........7.5 99.2 100.0 The slag from this furnace amounted to 46 per cent. of the total amount charged and was of the following average composition: Per Cent. Cu..............16.86 SiO2.............34.7 FeO.............18.8 A12O3.............13.0 CaO.............9.4 MgO.............2.7 S............... 0.47 As..............0.11 Sb...............0.006 Ag, oz per ton.....0.18

Jan 1, 1914

By Martin S. Maier, H. R. Nelson

THE diffusion of metals plays an important role in many metallurgical processes, 1,2 as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystallization and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved.1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms-self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radio-activity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes-lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-10 and bismuth10 using natural radioactive isotopes, and of gold11 and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited on one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc, 14-16 silver,17 and copper.18 The second method was used for the work described in this paper. MATERIALS The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by 1/8 in. thick. Samples of high-purity copper described by Phillips and Skinner19 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth&apos;s crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D&apos;Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By M. H. Cullender

The performance characteristics 01 gas wells producing from formations which fail to stabilize within a relatively short period of time are obscured by the interrelation of the coefficient (C) and the slope "n" of the conventional back-pressure curve q = C(P2 f- p2s)n An empirical method is presented whereby the characteristic or true slope (11) of the back-pressure curve may be determined for a particular gas well. For those gas wells which do not stabilize within a relatively short period of time, the coefficient (C) is considered as a variable with respect to time and as a constant only with respect to a specific time. Thus, the back-presrure performance of such a well is presented as a series of parallel curve5, each curve representing the performance of the well at the end of a given time interval. Through use of the method presented, a simple presture gradient is developed and maintained within the drainage area around a producing gas well during the test period in order that the variation of the coefficient (C) with respect to time does not obscure the true value of the lope. INTRODUCTION The back-pressure method of testing gas wells as set forth by Schellhardt and Rawlins1 is dependent upon the requirement that a series of flow rates and corresponding pressure data be obtained under stabilized conditions. These data arc then plotted on logarithmic coordinates of flow rate (Q) vs difference in squared pressures (P2f — P2s) in order to determine the constants (C) and (n) for Equation 1. With respect to this method of presenting the performance characteristics of a gas well, it should be pointed out that although Equation 1 is an empirical relationship, the form of the equation was justified to a considerable extent by an independent development by Muskat and Botset.2 This development was theoretical in nature; however, certain assumptions with respect to the type of flow existing (viscous vs non-viscous) were madc which may or may not be correct. As the use of the method presented by Schellhardt and Rawlins spread through the industry, it became evident that the method of testing was applicable for those wells which approached stabilized prbducing conditions within a relatively short period of time. Performance characteristics could not be determined by this method, however, for wells which approached stabilized protlucing conditions slowly over a considerable period of time. This characteristic of "slow stabilization" has generally been associated with gas wells producing frorn reservoirs of low permeability. As the demand for natural gas continued to grow through the years, a great number of wells were completed in reservoirs of low permeability which exhibited "slow stabiliz:~tion" characteristics. Consequently, the problem of determining the true performancc characteristics of these wells became more apparent. It is with this problem in mind that the isochronal performance method of determining the flow characteristics of gas wells is presented.

Jan 1, 1956

By Fred H. Poettmann, A. L. Benham

correlation of waters and identification of mixtures of two and three waters is important in secondary recovery evaluation studies and studies involving underground movement of waters. The importance of such studies suggests the need for a method to correlate a great number of water analyses to accurately identify and improve the understanding of mixtures of waters. Geochemical analyses of waters furnish a quantitative measure of each of the ions present in a water. Table L shows a portion of the data on many oilfield water analysis report forms in use today. Under "parts per million" are listed the quantitative amounts of each ion in milligrams per liter. Following the work of Stabler&apos; and Palmer", some laboratories have reported additional data to indicate the reaction capacity, or reacting value of each ion. Table I lists data under two subheads for the "reacting value". Under the first subhead, the reacting value is reported in gram equivalents per million, hereinafter called equivalents per million. This value is determined by multiplying milligrams per liter of the ion by a factor equal to the reciprocal of the equivalent weight of the ion. Under the second subhead (per cent) is listed the percentage of each ion based on the total equivalents per million. Sodium is not usually an analyzed value in routine analyses, but is determined by the difference between total negative equivalent per million values and the sum of all of positive ion values for which analyses were made. This difference is reported as sodium, hereafter labelled "sodium". On this basis, the subtotals of the equivalent per million and per cent reacting values of the positive and negative ions are equal. CORRELATION OF WATER ANALYSES DATA Previously reported methods for correlating oilfield waters have used part of the data in Table 1, and can be classified into two categories. Correlation by Chemical Character Correlation methods using the chemical character of waters, as represented by the per cent reacting values of the ionic constituents, have been used by Palmer2 and Tickell. These methods have the limitation of neglecting the ionic concentration of the waters. This limitation can be serious in areas where waters have the same chemical character, but differ in concentration. Correlation by Concentration of the Ionic Constituents The Reistle&apos; and the Stiff methods use the ionic concentration in parts per million and equivalents per million. These methods are effective in differentiating waters of similar chemical character and varying concentration, as in the highly saline waters of the Mid-Continent area. These methods have the disadvantage that they correlate waters by comparing many graphs of individual water analyses to determine the similarity to, or the variance from "type" waters. PROPOSED METHOD OF CORRELATING WATER ANALYSES DATA Correlation graphs presented in Fig. 1 represent water analyses data as points to facilitate the correlation of waters. The graph on the left of Fig. 1 is a plot of per cent reacting value of magnesium vs calcium. The right

By M. A. Torcaso, P. Raimondi

The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil. A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sor The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston-like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. INTRODUCTION A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two-phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would be represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil. called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition. of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important.

Jan 1, 1965

By C. G. Dunn, F. W. Daniels, M. J. Bolton

J. P. Nielsen—The data that Dr. Dunn and his associates have been obtaining are welcome checks on the theoretical aspects of grain boundary energies. With reference to the comments on the validity of the inter-facial tension concept, I should like to say that I have been having considerable difficulty myself in untangling the confusion between "interfacial tension" and "interfacial energy." The confusion however resolved itself for me when I learned that "interfacial tension" for solids, or at least crystals, is used with two distinct meanings. One meaning12. &apos; "hat is implied for "interfacial tension" is the work necessary to produce or increase the surface of the solid in question by a unit area, temperature and pressure held constant. This comes from the somewhat surprising but simple fact that surface tension and surface energy in the case of liquids are identical quantities. This synonymity has carried over to crystals, where it should be kept in mind that the tension connotation has meaning only by analogy with liquids and that no real stresses are being referred to. The only reason that there is apparently a set of stresses acting at a grain boundary junction is the optical illusion that liquid interfaces are being observed for the grain boundaries. The other meaning3,14,15 for the term has to do with actual states of stress in the surface of a material as would be measured by a system of forces applied to the surface to equate the surface stress state with that in the body of the crystal. J. B. Hess—Since the authors have proposed that the surface tension concept should be discarded in order to deal with the general case of interface energies in solids, their attention should be called to a recent paper by Gurney." The latter has shown, from a thermodynamic argument, that surface tension is a valid concept in solids. In fact, Gurney has rejected the idea that surface tensions are merely mathematical fiction and, instead, has given an interpretation of their physical reality. Finally, he has concluded that, as long as appreciable atomic migration takes place, specific surface energies and surface tensions must be equivalent in solids as well as in liquids. Accordingly, the authors&apos; eqs 2 and 3 can be written with equal accuracy in terms of interface tensions, simply by replacing each E,! with its numerically and dimension-ally equivalent Interfacial tension ?,,. If the interfacial tensions (or specific energies) are independent of interfacial orientation, as is true in liquids, then the general equations that define the geometry at equilibrium of the common junction of three interfaces reduce to eq 1. However, neglect of the effect of boundary orientation is never completely justified theoretically&apos; in dealing with crystalline solids; hence, use of eq 1 in such cases must always be considered as an approximation, though clearly a reasonable one for many purposes.1,2 At the same time, one should not be surprised that the assumption that interface tensions in solids are free from orientation

Jan 1, 1951

By John P. Huger

me phase diagram for the system Ag-Si has been established by thermal analysis. The diagram is a simple eutectic type with a eutectic at 3.0 pct Si and 840°C. From the liquidus curve and with the aid of regular solution theory, the thermodynamic properties of the liquid Ag-Si system at 1420 °C have been determined. Silicon exhibits positive deviations from Raoultain behavior at all compositions, while silver exhibits both positive and negative deviations. MEASUREMENTS of silicon activities in liquid iron alloys by means of distribution studies between the immiscible liquids silver and iron have been reported by Chipman, Fulton, Gokcen, and caskey.&apos; The applicability of this technique is dependent, however, on the accuracy of the silicon activity values in the Ag-Si alloys, particularly in the dilute silicon region. Darken and Gurry2 have shown that log ?si/(1-xSi)2 is approximately linear with composition, but uncertainty exists in the extrapolation to dilute solutions. Their calculations are based on the old Ag-Si phase diagram of Arrivaut3 and any variation in the position of the liquidus curves will strongly influence the extrapolation. The purpose of this study is to redetermine the Ag-Si phase diagram and calculate the associated thermodynamic properties. EXPERIMENTAL The Ag-Si phase diagram was determined by thermal analysis of liquid alloys. The alloys were contained in a 35 mm alumina crucible under a protective stream of purified argon. The crucible was placed inside a 64 mm alumina tube fitted with a gas-tight, water-cooled, copper head. The tube and assembly were heated in a manually controlled globar furnace. The temperature was measured with a Pt, Pt + 10 pct Rh thermocouple in a high-temperature porcelain protection tube. The thermocouple calibration4 was checked against the melting point of pure silver at the start and during the course of the experiments, and against both gold and silver at the completion of the experiments. The alloys were prepared from granular silver analyzing 99.95 pct Ag and powdered silicon analyzing 99.88 pct Si and 0.026 pct Fe. Approximately 150 g of alloy were used for each run. The composition of the alloy was determined by withdrawing samples of the liquid alloy with a vycor tube-aspirator bulb device. Analysis of solidified samples agreed, for alloys containing less than 23 pct Si, within ±0.3 pct Si of the calculated composition. Duplicate samples showed a variance within 50.05 pct Si of the mean analysis. The alloy was heated to 100&apos; to 20pC above the estimated liquidus temperature and then the furnace was adjusted to give an average cooling rate of 2" to 7°C per min. A cooling curve was obtained by taking potentiometer readings at 15-sec intervals. Several analyses were made by recording the thermocouple output on a high-speed, Stip-chart recorder, with the exception of run NO. 11, a minimum of two thermal analyses were made for each alloy and the cooling curves then obtained duplicated the liquidus and eutectic temperatures to about 1°C. RESULTS The results of the thermal analysis are given in Table 1, and are represented as the Ag-Si phase dlagram, Fig. 1. The eutectic composition was found

Jan 1, 1963

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.&apos;" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.&apos;-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet&apos;s solution.&apos; Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs&apos; = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors&apos; reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By W. M. McKewan, R. G. Olsson

In order to improve the understanding of the iron oxide reduction mechanism, the rate of equal molar diffusion of hydrogen and water vapor was measured through disks of porous iron and alumina. The measuretneizts were made at atmospheric pressure at 800°, 900- , and 1000°C. It is shown tint the reduction of dense hematite pellets with hydrogen at these temperatures and at atmospheric pressure is to a great extent limited by gaseous diffusion between the bulk-gas phase and the iron-wustile interface. THE investigation of the reduction of iron oxides with hydrogen has been the subject of numerous papers. Although the effects of temperature, pressure, and gas composition on the rate of iron oxide reduction have been studied, the actual mechanism of the reduction process has not been definitely determined. As a means of improving the understanding of the mechanism, the rate of equal molar counterdiffusion of hydrogen and water vapor was measured through porous iron and porous alumina disks at reduction temperatures. The alumina was used as a basis of compari-son because its pore structure is homogeneous and independent of temperature. The porous iron was prepared by the reduction of dense hematite disks with hydrogen at the temperature of the subsequent diffusion experiment. The hematite disks were made from pellets that were identical to those used by McKewan1,2 in his study of iron oxide reduction with hydrogen. In these investigations the weight loss and rate of movement of the various interfaces were measured as a function of the reduction temperature and gas composition. With these reduction data and the presently reported diffusion data it is possible to determine the importance of H2-H2O transport between the bulk-gas phase and the Fe/FeO interface to the reduction of dense hematite. APPARATUS AND PROCEDURE A porous iron or alumina sample was held in the base plate of a sealed canister containing porous granular wustite, as illustrated schematically in Fig. 1. The canister was suspended from an automatic recording balance in a vertical tube furnace through which flowed hydrogen and water-vapor mixtures of known composition at atmospheric pressure (0.96 atm). Hydrogen from the gas stream diffused through the porous sample, reducing the wustite in the interior of the canister. The water vapor that was formed diffused back to the gas stream. The rate of diffusion was determined from the recorded weightloss data. The furnace, automatic balance, and gas-metering equipment have been described previously.2 The main body of the canister and the tubing extension were made of stainless steel while the base plate was made of high-purity iron. The main body of the canister was % in. in diam. It held approximately 6 g of porous granular wustite that was prepared by reducing 0.1- to 0.2-cm-diam specular hematite particles at 900°C with an H2-H2O mixture of a composition near the iron-wustite equilibrium value. The upper end of the 1/8-in.-diam tubing extension was sealed with a segment of plastic tubing and a tubing clamp. The temperature at the top of the furnace was sufficiently high so that no water vapor condensed inside the extension. In the experiments with porous iron, iron oxide samples were prepared from reagent-grade hematite that was pressed and sintered in a manner previously described.&apos; The resulting pellets had a density of 5.15 ± 0.05 g per cu cm. Each pellet was centerless-ground

Jan 1, 1967

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965