Search Documents

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function' used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail' and the results are simple and generally applicable. 'The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy's law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

By Maxwell Adams

Considerable interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemisia tridentata, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of ,small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment. The stock wood, bark and branches contain no oil, the distribution of the oil being limited to the leaves and young shoots. There is a seasonal variation in the amount of oil contained. Samples collected on different dates gave the following amount of oil: May 1, 0.42 per cent.; May 27, 0.6 per cent.; June 30, 0.72 per cent.; Aug. 1, 0.9 per cent.; Sept. 10, 1.0 per cent. The increase appears fairly constant from early spring, when the leaves first appear, until light frosts occur in the autumn. When the plant is air-dried there is some loss of oil, as the following data will show: Two 100-lb. samples were collected at the same time. One was distilled when green; the other was air dried for

Jan 1, 1917

By Leon O. Hart

The nickel-chromium alloys of importance are those containing iron and those free from iron. The most important alloys containing iron, with regard to high tonnage, are the nickel-chromium steels. Straight nickel steel was introduced about the year 1889, but it was not until 1895, when it was found that the addition of chromium greatly increased the strength and resistance to shock, that nickel-chromium steels came into use. The three types of nickel-chromium steels developed at this time were: Type 1, containing 3.,50 per cent. nickel and 1.50 per cent. chromium; type 2, containing 2.00 per cent. nickel and 1.00 per cent. chromium; and type 3, containing 1.50 per cent. nickel and 0.50 per cent. chromium.

Jan 1, 1921

By R. Kossowsky

BRIDGMAN has listed five possible transitions in bismuth at 25°C which were observed as volume changes. He was unable however to detect the last three transitions by electrical-resistivity changes. Kennedy and LaMori have verified the pressures at the Bi 1-11 and Bi 11-111 transitions. They suggested however that the 125-kbar transition previously reported by Bundy3 actually corresponds to the 90,000 kg per sq cm transition observed by Bridgman.1 Jura4 reported a well-defined drop in resistivity at 92 kbar obtained by a four-lead method. The Bi 111-IV and Bi IV-V transitions have not been reported in any of the above-mentioned references.'-' Bundy3 observed a small dent in the low-temperature boundary of the Bi Vll region which is consistent with the presence of a 111-IV boundary. Zeitlin and Bray-man5 were the only ones to report small but well-defined drops in resistance of bismuth at 44.0 and 63.8 kbar, corresponding to Bridgman's 111-IV and IV-V transitions, respectively. High-purity (99.99 pct) 0.020-in.-diam 0.5-in.-long bismuth wire was used to calibrate the Uniram tetra-hedral high-pressure apparatus used in the present work. The bismuth phase changes at 25°C were correlated with changes in electrical resistance as a function of pressure. The output of a sensitive bridge constructed of carbon resistors and kept at a constant temperature of ±°C during the measurements was fed to the Y axis of a MoseleyX-Y recorder and the X axis was used for time scans. Specimens were pressurized using a hydraulic press with maximum capacity of 200,000 lb. Load was applied in increments of 2000 lb and held for about 3 min. The resistance was recorded at the end of this time period. Good contact was established below 20,000 lb. Typical recorder charts are reproduced in Figs. 1 and 2 which show that resistance fluctuations were practically nil during each time scan. Well-defined discontinuities in resistance were observed at 58,000 and 82,000 lb, Fig. 1. Two small but definite "blips" are noticed at 92,000 and 122,000 lb, Fig. 2. At 156,000 lb another drop is observed which

Jan 1, 1967

INTRODUCTION The regional characteristics of porphyry copper deposits in South America southward from Pantanos and Pegadorcito, Columbia, will be summarized. The age of formation of deposits spans the period from the Permian to the present. Where possible, the general characteristics and the individual structural features of the deposits are integrated into the plate tectonic model. Individual deposits cited in this chapter, located in Fig. 1, are the best known and most fully described, and form the Andean copper belt (Peterson, 1958). Smaller porphyry copper deposits fall both east and west of the line of large, high grade deposits (e.g., Chuquicamata and Toquepala) that make up the spine of this belt. Most of those smaller deposits (e.g., Mi Vida [Koukharsky and Mirre, 19761) are omitted from Fig. 1 and Tables 1 and 2, however. Neither the Andean orogen nor the individual deposits within it are as well de- scribed in the literature as are their counter- parts in the Cordilleran orogen of North America. Therefore, generalizations relying on regional geologic mapping, geophysics, and isotopic geochemistry lack details pertinent to this type of deposit in the Cordilleran orogen. The South American porphyry copper province has been described by Hollister ( 1974) to include most of the Andean orogen excepting the tin province of Bolivia. Porphyry copper deposits have not been commonly found within the tin belt, although copper-tin (e.g., San Rafael, Peru) and copper-tungsten (e.g., Llamuco, Chile) de- posits are known. James (1971) shows the depth to the Moho to be appreciably greater where the tin belt exists, but disclaims any genetic significance from the coincident appearance of the tin-tungsten province and the inhibition of porphyry copper development where the sialic crust thickens. Dates on tin mineralization in this belt (Clark and Farrar, 1973) are similar to some dates for porphyry copper mineralization known else- where in the Andean orogen. It seems that some mechanism is needed to explain the geographic separation of porphyry copper- molybdenum and simultaneous tin-tungsten- molybdenum metallization within the same tectonic system and appearing at similar distances from the trench. The thickened crust of the tin belt is one of the few known differences. Tables 1 and 2 list some of the most important porphyry copper deposits explored to date, but do not include Antaminas, Peru. or a number of other large skarn deposits

Jan 1, 1978

By Vernon Taylor

CANADA'S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada's total. In the British Empire, Canada's production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad's production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world's total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company's No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

By H. C. Fiedler

X HE development of the cube-on edge secondary re-crystallization texture in Si-Fe strip requires that normal grain growth be restrained. It has been shown that the degree of restraint and hence the completeness of secondary recrystallization depends upon the size and number of second-phase particles, which in turn is dependent upon the prior processing history.1y2 The purpose of this note is to show that, for heats in which manganese sulfide particles are providing the restraint to grain growth, the choice of hot rolling temperature depends upon the manganese content. The making and processing of the heats to the final gage of 0.012 in. has been described.3 The compositions are given in Table I. Apparent in Fig. 1 is the decrease in the ability of strips hot-rolled from 1175°C to undergo secondary recrystallization as the manganese content increases. It has been shown that 1175°C is below the solubility temperature of 0.014 pet S in even the 0.038 pct Mn alloy: and the observed behavior is attributed to an increasing fraction of the sulfur forming large manganese sulfide particles at the heating temperature for hot rolling. This fraction of the sulfur is thus unavailable to subsequently form the small, uniformly dispersed particles which are needed to restrain normal grain growth. Since the sulfur is completely in solution at 1325°C,3 strips from all three alloys show strong secondary recrystallization behavior when hot-rolled from that temperature.

Jan 1, 1969

Stripping of the Exotica open-pit mine, which is proceeding at about 120,000 tpd, is dwarfed by its proximity to the 500-million-ton Chuquicamata tailing pile. The excavating work is being carried on smoothly and efficiently and, as of the end of October, accounts for the removal of 77 million tons of total material of which some 200,000 tons is stockpiled ore. Diamond drilling has outlined an orebody 5900 ft long and 3400 ft wide containing an estimated 153 million tons of ore at 1.35% recoverable copper based on 80 % extraction.

Jan 11, 1969

By A. J. Erickson, W. W. Atkinson

Concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine, are not fundamentally new, but represents expansion of earlier ideas. The basic philosophy is that a high quality geologic data base is necessary and should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed, as well as a mu1tiple overlay system for recording data gathered in surface mapping.

Jan 1, 1984

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

By Alan D. Hoagland

The Flat Gap mine, are important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolonmite and accessory pyrite. There is local minor galena and very rare barite and fluorite.

Jan 10, 1962

By Philip N. Adler, Harold Margolin

Univariant equilibria between the Ibcc, IIhcp, and UIfee phases of thallium have been determined and indicate a triple point at 110°C and 37 kbars. Calculated II —I transformation curves are compared with the experimental. Transformation volumes and/or enthalpies are calculated and enthalpies are compared with available data. ThE triple point of solid thallium has been reported by Bridgman as 153°C and 38 kbar.' More recently, Jayaraman et at.2 have reported the triple point as near 115°C and 39 kbars. Meyerhoff and Smith,3 assuming the elevated-pressure modification of thallium is fcc, as Kaufman suggested,4 and that it is continuous with the room-temperature fcc phase in the Tl-In system, have used pressure data up to 5 kbars to predict the triple point at 162°C and 35.8 kbars. Piermarini and weir5 have indeed found the elevated-pressure phase to be fcc. The effect of variations of pressure and temperature in the IIhCp — Ibcc transformation in thallium have also been reported by werner6 and more recently by Ponyatovskii.7 The work reported here is part of an investigation of the effects of temperature and pressure on the Tl-In system. I) EXPERIMENTAL PROCEDURE The onset and progress of transformation were determined by changes in resistance. A commercially available tetrahedral-type pressure apparatus was used. Specimens of 0.060 in. diam, representing 0.63 pct of the cell volume, were encased in AgCl and mounted in pyrophyllite, as shown schematically in Fig. 1. It can be seen that the specimen is in series with the graphite furnace. Resistance changes of 0.1 pct could be detected with a Kelvin bridge. Resistance of the sample was of the order of 1 milliohm. Other pertinent details in regard to calibration and cell-assembly design are given elsewhere.' Temperature calibration of the cell was carried out in two ways as a function of input wattage. Through a hole drilled in the graphite furnace, a chromel-alumel thermocouple was inserted into the AgCl to a point 0.010 in. from the sample, with the

Jan 1, 1964

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By Arthur Gibson

Synopsis.-A new feature in coal mining, where the coal is to be conveyed from a high to a lower elevation and the topography of the country is such as to preclude surface haulage. The distance from the mine to the tipple inn this instance is about 3,000 ft. and the difference in elevation between the terminals 321 ft., of which 225 ft. occurs in the first 1,300 ft. from the loading terminal. A mine car was designed especially for this plant consisting of two tramway buckets on one pair of trucks, the buckets being lifted from the truck, attached to the train line automatically, and conveyed to the tipple. THROUGHOUT eastern Utah, in the Book Cliff range and the Wasatch plateau, the coal-bearing measures are admirably exposed, in the bold and for the most part bare escarpments. The geology is simple, the rocks being almost flat, or at the most dipping not more than 10 per cent. The coal beds occur in a formation, or group of strata, consisting of sandstone and shale, 600 to 800 ft. thick, which has been correlated with the Mesaverde formation of the Cretaceous. Above this occurs about 2,000 ft. of alternate layers of buff-colored sandstone and shale. Below the coal lie the Colorado shales, which are estimated to be about 1,500 ft. thick, below which are the red rocks of the Jura-Trias. As a rule the coal beds all clip in a northerly direction and under the high mountain. The canyons opening out into what is known as Castle valley all cut the coal beds, and the beds rising in the direction of the valley are found frequently high up on the escarpment, often as much as 1,000 ft. above the valley. The surface features of the region have an economic bearing on the availability of the coal. The valleys and gulches in the Colorado shale extend out from the coal areas across the edge of the plain, so that it is impracticable to build transportation lines parallel with the boundaries of the field within several miles of the coal land. It will be necessary, therefore, to build branch lines up to the coal lands from points on the Denver & Rio Grande Railroad traversing Castle valley.

Jan 10, 1914

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950

By D. W. Loughridge

INTRODUCTION Raising capital in the 1990s is a timely subject. However, many of us thought why should raising capital in the 1990s prove to be unlike it was in the 19805, the 1970s, the 1%0s, or earlier? There are a lot of creative people in banking and in corporate treasury departments. New tools and techniques are continuing to emerge, many of which are discussed in other papers in this book. While we have new financing tools at our disposal, the underlying issue has not changed. Projects and investments must be judged on their own merits. If they cannot be justified by conventional financial analysis, they should not be built. If they can be justified, it is likely that the financing will be available. The challenges faced in raising capital in this decade will persist to the next. The issues of the 1980s -- currency fluctuation, disruptive merger and acquisition activity, commodity price volatility, political risk, and debt crisis -- will all persist in an increasingly international business environment. I will focus on the financing we have just completed for the Escondida Copper Project in Chile. The Escondida financing is structured along the classic project financing model developed in the late 1970s, but it deals with issues of the 1980s and the 1990s. The financing was intriguing, not just because of the technical issues involved, but also the challenge of reaching an agreement in a large and diverse group. Escondida had the one essential feature that made its financing possible. It was commercially very attractive. It would produce at low cost a commodity (copper concentrates) that direct consumers felt would be in tight supply. The project had the direct support not only of its sponsors, but also its customers, and, very importantly, its host government. The non- recourse financing of Escondida would not have been possible without the support of these parties, and without the robust economics that made this effort worthwhile. The issue was more complicated. Operations in all parts of the world entail some political exposure. This project is in Chile, where there was a constitutional requirement that a plebescite be held when the project would be in its early stages. This plebescite would determine the fate of a 15 year old military dictatorship. The project is copper, a commodity generally deemed to be in surplus. Copper has a history of price volatility (whose price has varied from $.58 to $1.53 per pound over the past two years). It is politically sensitive, not only in Chile, but in the United States, Canada and other developed countries. The project is international, with all the problems of dealing with a variety of currencies, a variety of cultures, and a variety of laws and commercial practices. The project is also large and capital intensive, with a total cost of U.S. $1.1 billion. ESCONDIDA PROJECT Escondida, the largest known copper ore body in the world, was discovered in March of 1981, by Utah International in a joint venture with Getty Oil Company. In 1984, both Utah and Getty were involved in ownership changes, Utah being acquired by BHP. A later restructuring of the ownership of Escondida resulted in BHP, as manager, carrying a 60% interest, Rio Tinto-Zinc Corporation (RTZ) 30%, and a consortium of Japanese companies led by Mitsubishi Corporation with 10%. The Japanese consortium is incorporated as JECO (Japan Escondida Corporation). This ownership structure, which spread ownership around the world, was the first tangible step toward managing both the commercial and political risk associated with the project.

Jan 1, 1990