Search Documents

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3'4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal ('junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill' and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

By T. F. Petty

Oil and gas production in North Central Texas has been found in sands and limestones in the Cisco, Canyon, Strawn and Bend series of Pennsylvanian age and in lime of pre-Pennsylvanian age. Production ranges in depth below the surface from 150 to 4500 ft.; a few wells have been drilled to depths in excess of 5500 ft. and penetrated rocks of pre-Cambrian age. In Table 1, the average depth of the pools is shown. No mention, however, is made in this table of approximately 30,000 bbl. of oil produced in Callahan County from a pre-Pennsylvanian pay, presumably the Ellenberger, and an excess of 1,000,000 bbl. of oil produced from limestone, which has been identified as Silurian in the south part of Young County. This well is being produced at the present time. In Table 1 a great many pools of minor importance are listed, which are merely productive spots, and throughout the various producing counties there are numerous similar spots, which might be listed as pools. Their production, however, is listed in the county totals. In Table 2, the totals of the oil wells, gas wells, and dry holes drilled before Jan. 1,1935, include only wells on which records are available to the writer. In Brown, Callahan and Shackelford counties 2924 very shallow wells (150 to 600 ft. deep) have been drilled, on which the record is not available. Possibly there are other wells that were drilled before the district was adequately scouted. No classification as to the depths of this total of 30,644 wells is available at present. Initially, nearly all the oil wells of North Central Texas produced gas, and several areas producing dry gas have been partly developed. A number of casinghead gasoline plants strip the gasoline from the gas produced with the oil, and the manufacture of carbon black is an important industry in Stephens County. Dry and residue gas are marketed through systems serving the various towns of the district, San Angelo to the southwest and the cities of Forth Worth and Dallas to the east. Considerable gas is used in repressuring several pools, the most important of which are the Stover of Brown County and the Cook of Shackelford County. During the past year, 32 gas wells were completed, adding a

Jan 1, 1935

By F. X. Tartaron

The comparison of actual energy of comminution with theoretical surface energy presents a wide gap. On the other hand, Solid State Theory presents a viewpoint that places actual energy of breakage in understandable relationship with the theoretical strength of materials. Therefore the physical background of comminution theory favors Kick's Law. A11 discussions of comminution theory appear farfetched when comparison is made of the actual energy of crushing with the energy input called for by thermodynamic theory. Quoting Taggart:' "The work required to crush halite was of the general order of 0.10 kg cm per sq cm of new surface produced (based on air percolation) whereas the theoretical energy of this new surface, based on thermodynamic calculation by a number of investigators is 1 x 10'4 kg cm per sq cm or the work expended was 1000 times the new surface energy — an indicated crushing efficiency of 0.10 pct." It is frustrating to probe into comminution theory with the prospect that the energy one is measuring is 99.9 pct waste energy. Do the laws of comminution deal with energy consumed by mineral breakage or with waste heat energy? There seems to be something wrong. Solid State Theory may provide the answer. The following statement is particularly apt to the situation: "The fundamental fact about metals and indeed all materials, is that they are much weaker than they should be. By this, we mean that if the stress required to cause a given plane of atoms to slip past a neighboring plane is calculated from basic atomic and Solid State Theory, the resulting number is some 1000 times too large to be accounted for by errors in approximations or assumptions. We know now that this is due to dislocations, and we even have a fair understanding of the details of the process by which dislocations make a crystal weak. An intriguing possibility which suggests itself, results from the discovery of very minute metallic crystals which are apparently free of dislocations and which have a strength approaching the ideal value for a perfect crystal." Here we have an extraordinary reversal of the situation. The actual energy for breakage is only one-thousandth the theoretical instead of 1000 times as given by Taggart. But the theoretical energy presented by Solid State Theory is the binding energy between atoms (or ions) in a crystal lattice. This is the kind of energy envisaged by Kick's law. The surface energy or the other hand corresponds to Rittinger's law. Comparison of theoretical with actual, on the basis of surface or on the basis of Rittinger's law, seems to present an absurdity; yet Rittinger's law is confirmed by an impressive array of experimental evidence. Comparison of theoretical and actual on the basis of Solid State Theory or, in other words, on the basis of Kick's law seems reasonable; yet there is not a scrap of evidence to verify Kick's law. The situation appears paradoxical, but the developments in the next section of this paper show that the paradox is a hint to a strange turn of events. ENERGY-WEIGHT FRACTION FUNCTION charles3 has presented a final equation showing the relation of energy consumed in comminution to size of product n{-1) a-n + 1 E is energy, C is proportionality constant, a and n are constants and k is the coarsest size in the ground product (size modulus). In the course of study of a large amount of experimental evidence, Charles discovered that in the general case, a-n + 1 approximated zero. For some reason, a and n differed only by unity. But if a—n + 1 = 0 within experimental error, then it is obvious that Eq. 1 states that it requires an infinite amount of energy to grind any sample to any size. This is a case where nature gives an absurd answer to a man-made mathematical equation, hence something is wrong with the equation. An adjustment must be made to fit the equation with experience. TO reveal the nature of the adjustment, the differential equation preceding the second integration in Charles' group of equations is given When Charles integrated the quantity xa-n it was almost impossible for him to realize that he was dealing with a special case of integration and that

Jan 1, 1962

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.1 It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to be drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the ?' phase," CuA12." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in ?' lying parallel to this plane are roughly similar to those opposite it in the matrix.' The formation of ?', however, is preceded by the formation of a transition lattice ?', which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly perfect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.4-8 Particles of ?' may be recognized microscopically and form a well-defined Widmanstätten figure.* The ?' lattice is recognized by the occurrence of diffraction lines on powder photograms or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6.7,1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a few hundred atoms in diameter, probably of the composition of "CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact merely ?' in a high state of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett's "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By William G. Christy

EFFORTS at smoke abatement date back to the year 1273 in England when a law was passed prohibiting the use of "sea cole." The law was not enforced, so King Edward I, 33 years later, appointed a commission "to enquire of all such who burnt sea cole in the city or parts adjoining, and to punish them for first offense with great fines and ransomes, and for the second offense to demolish their furnaces." Many other commissions have since been named to investigate the smoke problem in England, but it still persists in many British cities. In the United States the movement to abate the smoke nuisance started in certain Middle Western cities, and has made considerable progress. Until recently, the coal-producing industry co-operated little in smoke¬abatement programs, taking the attitude that smoke elimination is the dealer's or user's responsibility; and the dealers, in turn placed the responsibility entirely on the user.

Jan 1, 1942

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By E. Stamboliadis

Dithiophosphates are reaction products of phosphorous pentasulfide with various organic compounds such as phenols, alcohols, mercaptans, dioalcohols, amines, and nitrides. The products with alcohols are commercially known as "aerofloats" and these are investigated in this presentation. It appears that the formation of insoluble metal dithio phosphates is responsible for their collecting properties with minerals." In this aspect they are very similar to xanthates.3 The solubility of metal dithiophosphates depends on the number of carbon atoms in the organic chain of the corresponding alcohol. An empirical mathematical model is presented here. It allows one to predict the number of carbon atoms necessary to ensure that a certain metal dithiophosphate will form at a selected pH value of the water solution. The Nature of Dithiophosphates Dithiophosphoric acid is the product of the reaction of phosphorus pentasulfide with an alcohol, as shown in the following equation: [P2S3 + 4 ROH - 2 (RO)2 PS2H + H2S (1)] where R stands for a hydrocarbon chain. The acid so produced can be neutralized by a base to produce the corresponding salt as shown in the following: [(RO), PS2H + NH- (RO)2 PS, NH,. (2)] In this aspect dithiophosphates are similar to xanthates, the only difference being the substitution of the tetravalent carbon atom in the xanthate polar group by a pentavalent phosphorus atom in the dithiophosphate group. This difference implies at least two characteristics: (1) that there are two hydrocarbon chains associated with the polar group so that an increase in the number of carbons of the single chain is expected to have a pronounced effect on the flotation properties, and (2) that the bond between the sulfur and the central atom is stronger than in the xanthate group. This probably leads to a decrease in both the polarizability of the electronic cloud of the sulfur and the interaction with cations.3 However, what is lost in the dithiophosphates by having a weak polar group can be gained by an increase in the number of carbons as will be seen later. Taking into account the size of the atoms involved in a dithiophosphate molecule, as listed in Table 1, It is possible to draw an approximate diagram of its structure as shown in [Fig. 1]. It is assumed here that the length of the single hydrocarbon chain is equal to that of the corresponding alcohol. Preparation and Purification Acid dithiophosphates can be prepared, as previously mentioned, in accordance with Eq. 1. The rate of this reaction is too slow at room temperature and can be improved by increasing the temperature to about 60° or 80°C7 or by evacuating the system. In our investigation evacuation was performed by a water aspiration pump. The dithiophosphoric acid so produced is liquid and dissolves in the alcohol. At the end of the reaction the product is filtered from the remaining P2S3; and dissolved in petroleum ether. By blowing anhydrous ammonia gas into the ether phase the ammonium salt forms as a white precipitate and can be sepa-

Jan 1, 1977

By T. G. Richardson, F. M. Perkins

In the recent paper of Richardson and Perkins entitled "A Laboratory Investigation of the Effect of Rate on Recovery of Oil by Water Flooding,"' the authors found very little appzrent effect on oil recovery of having free gas saturation present prior to water flooding in unconsolidated sands. We agree that the effect in this particular system was small but do not feel that the data presented should be regarded as disproving work of others which has shown an appreciable effect. The authors do not make such a claim, but neither do they advance an explanation of the difference. In our experience the following factors must be carefully considered when studying the relation between residual oil saturation after water flooding and initial free gas saturation: (1) the magnitude of the inherent residual oil saturation, i.e., the residual oil saturation with no free gas; (2) the increase in oil-water viscosity ratio with pressure lowering if the gas saturation is obtained by solution gas drive; and (3) the oil shrinkage which occurs with pressure lowering and gas evolution. The system studied by Richardson and Perkins gave residual oil saturations as low as 20 per cent without free gas present, and one should perhaps not expect much further lowering. As an illustration of the magnitude of the effect when the residual oil saturation is inherently higher we submit the accompanying figure. These data were obtained on an unconsolidated sand under elevated pressure in a system similar to the one described by Richardson and Perkins. Gas saturation was established by gas drive before water flooding. The viscosity ratio was 600:1 under the conditions of the displacement. Here the gas was extremely effective in reducing residual oil saturation. This fact was also indicated by Kyte, et al.2 Their plots of residual oil saturation vs initial gas saturation show trends of greater free gas effect with higher oil viscosities. The pressure-dependent effects were not discussed by Richardson and Perkins. They should be separated from the free gas effect if the objective of the study is a correlation of residual oil saturation vs initial free gas saturation. The increase in oil viscosity when gas is released from solution tends to increase residual oil saturation. This effect is rather small in the viscosity range of kerosene. A Buckley-Leverett calculation, assuming an increase in viscosity ratio from 1.2 to 1.8, indicates an increase in residual oil saturation of about 1 per cent of pore volume. Thus, one would expect this system, if operated at constant viscosity ratio, to show a slightly greater free gas effect. As Dyes- as shown, oil shrinkage can offset the beneficial effect of free gas on waterflood oil recovery, if the gas saturation is established by depletion. Since

Jan 1, 1958

By T. E. Leontis

Several publications1-7 during the past few years have demonstrated the markedly greater effect of cerium, as compared to all other alloying elements, in enhancing the strength and creep resistance of magnesium at elevated temperature either with or without the presence of other elements. In the work reported in Ref. 1-6, the cerium was added in the form of Mischmetal, which contains all the rare earth elements in essentially the same proportions as they occur in monazite sand, the principal ore of these metals. Mellor and Ridley7 have presented the creep characteristics at 200°C of magnesium alloys prepared both with pure cerium and with Mischmetal. Up to the present time, however, no comprehensive study of the effect of the various component elements of Mischmetal on the properties of sand-cast magnesium has been made. This hiatus in magnesium technology undoubtedly is associated with the difficulty in obtaining the rare earth metals separately. This investigation provides such a survey, the object of which was to determine which of the elements present in Mischmetal contributes the greatest effect in developing high strength and high resistance to creep at elevated temperatures. Toward this end the compositional variation of these properties has been determined as a function of temperature in the following alloy systems: 1. Magnesium-Mischmetal 2. Magnesium-cerium-free Misch- metal 3. Magnesium-didymiuin 4. Magnesium-praseodymium- lanthanum 5. Magnesium-cerium 6. Magnesium-lanthanum This designation, based on the names of the metals as furnished by the producer, is used throughout the paper in order to avoid the complicated system of listing all the elements present in the more complex alloys. The composition of the metals and the alloys is discussed in detail below. Preparation of Alloys ALLOYING INGREDIENTS The chemical composition of each of the six alloying ingredients used to prepare the alloys reported in this paper is given in Table 1. In each case, the percent total rare earths, percent cerium, percent neodymium, percent praseodymium, and percent thorium were determined in addition to the listed impurities. The percent lanthanum was determined by difference from the total rare earth content and consequently includes the other elements (samarium, terbium, yttrium, etc.) present in Mischmetal. These additional elements, however, seldom amount to more than 1 to 2 pet of the total rare earth content of Mischmetal. The iron content of the Mischmetal is considerably lower than that of the other metals. This grade of Mischmetal is now readily available. The metals are listed in the order of decreasing complexity. Elimination of the cerium from Mischmetal results in what the trade calls "Cerium-free Mischmetal." Carrying the separation a step further by eliminating the lantha-

Jan 1, 1950

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962

By Harry Warren

THE Geology Department of the. University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two-fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals: The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type. ;-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-gold in native form. (2) Waneta variety-gold as telluride.

Jan 1, 1937

By F. M. Hamilton, H. F. Ameen

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

[Trans. No. Place Date Vol. Page 1, Wilkes-Barre, Pa.* .... May, &apos;71.. 1 3 2. Bethlehem, Pa Aug., &apos;71.. 1 10 3 Troy, N. Y Nov.,&apos;71.. 1 13 4. Philadelphia, Pa Feb., &apos;72.. 1 17 6. New York, N. Y •.... May, &apos;72.. 1 20 6. Pittsburgh, Pa..:.Oct., &apos;72.. 1 25 7. Boston, Mass Feb., &apos;73.. 1 28 8 Philadelphia, Pa.&apos; May, &apos;73.. 2 3 9. Easton, a Oct., &apos;73.. 2 7 10. New York, N. Y Feb., &apos;74.. 2 11 11. St. Louis, Mo.* May, &apos;74.. 3 3 12. Hazleton. Pa Oct.. &apos;74.. 38 13. New Haven, Conn Feb., &apos;75.. 3 15 14. Dover, N. J.&apos; May, &apos;75.. 4 3 16. Cleveland, 0 Oct., &apos;75.. 4 9] [ ]

Jan 1, 1925

By W. C. Lacy

A WIDE variety of metalliferous deposits in Peru shows a close and consistent relationship to intrusive and extrusive igneous rdcks. This relationship furnishes a clue to the comp(osition of ore-bearing fluids and to the timing in separation of these fluids from differentiation magma Conclusions presented here are based on ten years&apos; study of a large number of metalliferous deposits in Peru. The most important of these areas are shown in Fig. 1. The structural relationship of meta1 mineralization to the intrusive series and of the members of the series to each other can be illustrated by three examples: I The well described Cerro de Pasco (Ref. 1, p. 160) sulfide mass shown in Fig. 2 is localized along the &apos; eastern contact of an agglomerate-filled crater. Quartz-monzonite porphyry and related intrusive breccias, which in places border the pyrite mass On west, are replaced by the pyrite and cut by later transverse vein structures. Late unmineralized but

Jan 1, 1958