Search Documents

By L. M. Howe, J. Gordon Parr, E. Saarema

THE decreasing solid solubility limit at the titanium-rich end of the Ti-Cu constitutional diagram,' Fig. 1, suggests the possibility that titanium-rich alloys may be age-hardenable. However, results obtained by Holden et al. reproduced in Fig. 2 show that after quenching from 790°C the age-hardening of an alloy containing 1.7 pet Cu is very slight, while a 0.8 pet alloy decreases in hardness, during heat treatment at 400°C. It was believed possible that powder samples of alloys might show different results from the lump samples used by Holden et al., since small particles are often more sensitive to diffusion processes than larger samples. Consequently, a 1.9 pet (by weight) Cu alloy was made by the technique of levitation melting," checked for homogeneity, and filings of 48-65 Tyler screen size were cut from it for aging experiments. The filings were helium-quenched (by a technique described previously)' from 790°C, sealed in vacuo in silica tubes and aged at temperatures of 400°, 450°, and 500°C. Microscopic and X-ray examinations failed to reveal any structural changes during the aging process. This is not too surprising since early stages of precipitation do not usually manifest themselves in ways that are readily detectable by metallographic methods, and the extent of precipitation on overaging a 1.9 pet alloy is very small. However, hardness readings (taken on a Bergs-man micro hardness tester, using a 25 g load applied to a diamond indenter) do show a hardness peak at each aging temperature, Fig. 3. About a dozen readings were taken on each heat treated sample; the highest reading and the lowest reading were ignored and an average taken of the remaining values. In

Jan 1, 1957

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

By K. J. Kutz, F. A. Nice

Drilling of the second shaft at Texas Gulf Sulphur Co.'s Cane Creek potash operation southwest of Moab, Utah, is perhaps the largest undertaking ever made by private industry in the field of rotary shaft drilling. The new shaft, known as No. 2, is located within the plant area, about 400 ft northeast of the No. 1 shaft. This location within the pillar of the first shaft allowed utilization of a great deal of in- formation gained prior to and during sinking of the original No. 1 shaft, a conventionally sunk 22-ft diam shaft 2789 ft deep. The No. 2 shaft will be used for auxiliary transportation of men and supplies, and is steel lined with a 48-in. ID casing. The top 825 ft of the shaft is in predominantly red sandstone with interbedded shales. From 825 ft to 2800 ft, which is the top of the salt beds, the rock is mostly limestone with interbeds of anhydrite and shale.

Jan 9, 1968

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman' by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman' five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

By Cuppam Dasarathy

THE object of this note is to report briefly certain results of investigations on the Fe-In phase diagram. BISRA-high purity H-iron and 99.9 pct pure indium were used to prepare the alloys. The experimental techniques consisted of thermal analysis, optical metallography, and X-ray diffraction. A phase diagram based on the present results as well as those reported earlier by the author' is shown in Fig. 1. It is seen that the liquidus points fall on a smooth line which meets the monotectic isotherm at 1470°C. The liquidus extends up to 3.4 at. pct In. The phase boundary separating the two liquidus L1 and L2 is shown dotted. The experimental solidus meets the monotectic isotherm at -0.9 at. pct In. The 6/6 + L2 boundary drops steeply to the 6 + La/y + L2 boundary at -1350°C. In this region, it is impossible to detect satisfactory thermal arrests because of the steep phase boundary. The present diagram shows that indium lowers the temperature of the d/y transforma-tion and raises the temperature of the y/a transfor-mation. The y +d region is found to be very narrow. Indium gives rise to a restricted y field when alloyed with iron. The width of this field is between 0.4 and 0.5 at. pct In. Details of the alloys containing 40 and 50 at. pct In have already been reported by the author' and the transformation temperatures of these alloys are included in Fig. 1. It appeared from optical metallography and X-ray diffraction that the room temperature solubility of indium in a iron is less than 0.28 at. pct since alloys of 0.28 at. pct In and above, slow cooled to room temperature, contained dark etching second phase particles situated both in the matrix and grain boundaries of the a-grains, see Figs. 2 and 3. These particles were identified to be unalloyed indium by X-ray diffraction. The lattice parameter of the a phase reached a maximum of 2.8672A at the indium level of -0.28 at. pct. The present diagram, Fig. 1, is in substantial agreement with that of Stadelmaier and Fiedler' except for certain differences in detail. For example, they found the monotectic composition and temperature to be 7.0 at. pct In and 1443oC, respectively, while the present work indicates them to be 3.4 at. pct In and 1470°C. The 6 + L2/y + L2 transformation is indicated in the present work to occur at -1350°C, whereas Stadelmaier and Fiedler find this to occur at -1320°C. They also claim that the width of the y field is 0.2 at. pct In while the present work shows the width to be between 0.4 and 0.5 at. pct In. 1) Indium, when alloyed with iron, gives rise to a restricted y field, the width being >0.5 at. pct In.

Jan 1, 1970

By Harry Udin

IN 1948, the writer and his associates determined the surface tension of solid copper by balancing the force of surface tension in a very fine wire against an external load.' At that time we, in common with other early workers, assumed that grain boundary energy in a pure metal is very small in comparison to the energy of an external surface. Accordingly, we neglected the internal surface energy of the coarse-grained specimens. Since that time, experimental evidence has accumulated showing that grain boundary energy, far from being small, is generally about one-third of the energy of an external surface.2-4 This is sufficient to introduce a significant error into our determination. The differential equation governing equilibrium is: wdl - yds, + y*ds2 [I] rather than wdl = yds as originally written. w is the balancing force in dynes, 1 the length of the specimen, sl the external and s2, the internal surface area, y the copper/ copper vapor surface tension, and y* the grain boundary tension. Fortunately, we had made for another purpose a careful study of the size and shape of the grains, and found that the boundaries, with rare exceptions, traversed the specimens and were perpendicular to the wire axis. For this case, eq 1 leads to w = rry -(n) r2y* [2] where r is the wire radius and (n is the number of grains per unit length. A count of some twenty 5-mil wires indicated that - n became 80 & 10 after a short anneal near the melting point, and remained nearly constant for as long as 96 hr at temperature. An assumption of y* = 1/3y leads to a defining eauation for r: [31 The term in the brackets may be considered a correction factor applied to eq 11 of ref. 1. Upon applying this factor, the surface tension of solid copper at its melting point is found to be 1650 & 100 dynes per cm, rather than 1370 as previously reported.' The new temperature coefficient is —0.55 dynes per cm per "C. Grain boundary energy is more significant than surface energy to the physical metallurgist. It is evident from eq 2 that a series of experiments with wires of different grain size can lead to an evaluation of y*. The details of such an experiment are being worked out now. References 1 H. Udin, A. J. Shaler, and J. Wulff: The Surface Tension of Solid Copper. Trans. AIME, 185, 186-190; Journal of Metals (Feb. 1949) TP 25303. 2 G. L. C. Bailey and H. C. Watkins: Surface Energies in the System Solid Copper-Molten Lead. Proceedings Physical Society. (London) (1950) 36B, 350. 3 L. H. VanVlack: Inter granular Energy of Iron and Some Iron Alloys. Ph.D. Dissertation, Univ. of Chicago, Sept. 1950. 4 . P. Greenough: Grain Boundary Energies in Silver. R.A.E. Report, No. Met. 52. (May 1950) Fan-borough, Hants, England.

Jan 1, 1952

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By Howard E. Parkinson, John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry's needs. The Bureau programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine communications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved mine communications systems. In May 1975 the U.S. Bureau of Mines (USBM) conducted a mine communications technology meeting to provide a brief overview of the USBM communications technology developments in the past 5 yr. This meeting lasted for 1 1/2 days. Therefore, I have elected to narrow this paper to a brief review of recent underground mine communication developments. The following will be discussed: 1) Ultra-high frequency (UHF) radio for fan hole drill operators;

Jan 1, 1978

By G. T. Smith, R. C. Moyer

Cadmium, along with other impurities such as lead, gallium, germanium and indium, is characteristically found associated with zinc ores, the average ratio of zinc to cadmium being about 200 to 1. The increasing demand for cadmium has led most zinc producers to develop a means for its recovery. The separation and recovery of this byproduct constitutes an important development in the metallurgical field. Zinc sulphide concentrates, principally from domestic sources, are processed at Donora Zinc Works and they assay approximately 60 pct zinc, 30 pct sulphur, 0.37 pct cadmium, and 0.8 pct lead. Concentrates are roasted to convert zinc sulphide to zinc oxide. Sulphur evolved as sulphur dioxide is used to manufacture 60º Baume sulphuric acid by the lead chamber process. The roasted calcine is sintered to remove the remaining sulphur and volatile impurities. Fume from the sintering machines is collected by Cottrell pre-cipitators and sent to the Cadmium Department for cadmium removal. The sintered product, a crude zinc oxide, is then mixed with coke and salt and charged into horizontal retorts for reduction to zinc metal. Furnace residues are then passed through a Waelz kiln which recovers practically all of the remaining zinc as an oxide. This oxide is collected by Cottrell precipi-tators and returned to the sintering plant for further processing. The following discussion covers operating procedure, and equipment used in the Cadmium Department for the manufacture of cadmium and its byproducts. (See attached Flow Sheet, Fig 1.) The production of cadmium may be divided into several steps, each of which will be discussed separately. These steps are as follows: 1. Raw Materials—Sinter Plant Cottrell dust, acid sludge and sulphuric acid. 2. Sulphating—Separation of lead. 3. Purification—Separation of impurities other than zinc. 4. Precipitation—Separation of cadmium from zinc. 5. Briquetting—Preparation of sponge for charging to furnace. 6. Smelting—Distillation of cadmium metal. 7. Remelting—Casting into commercial shapes. 8. Recovery of Rare Metals—Separation of germanium, gallium and indium. Raw Materials The raw material, or Sinter Plant Cottrell dust, from which the cadmium is manufactured, is recovered by Cottrell units collecting fume from two Dwight-Lloyd sintering machines. An average analysis of this dust is 36 pct zinc, 1.5 pct sulphur, 17 pct lead, and 5.5 pct cadmium, with associated elements in smaller amounts. A lesser tonnage of material removed from the sintering machine fans, and called fan cleanings, is also treated for cadmium. It is lower grade material and analyzes approximately 41 pct zinc, 1.2 pct sulphur, 14 pct lead, and 4 pct cadmium. Cottrell dust and fan cleanings are delivered to the Cadmium Department by monorail crane in bell-bottomed dump buckets. Acid sludge and 60" Bauine sulphuric acid are received from the Acid Department. The acid sludge is a mixture of lead sulphate, sulphuric acid and zinc sulphate, and is recovered mainly from the floors of the acid chambers or storage tanks. The acid sludge is delivered to the Cadmium Plant in a lead lined bucket. The 60º Baume sulphuric acid is delivered through a lead pipe to a lead lined storage tank. Sulphating Four well ventilated lead lined sulphating tanks, 8 1/2 ft in diam by 12 ft deep, are used. These are steel tanks lined with 20 lb lead on the bottom and 16 lb lead on the ides, equipped with Hastelloy side agitators. 15 hp motors drive 24 in. propellers at 450 rpm. There are water connections to stuffing boxes to keep sludge from entering the bearings. The tanks are covered with removable wooden lids and are connected to marine plywood

Jan 1, 1950

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By John W. Bell

The aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½-ft. Huntington mill was used.

Jan 1, 1918

By R. T. Hukki

This paper presents a preliminary analysis of the fundamental relationship between the net energy used and the respective product size throughout the entire range of sizes covered by crushing and grinding, and an attempt to find a sensible correlation between the existing theories. Walker, Lewis, McAdams, and Gilliland' have given the following differential equation of a general form for comminution: dE = -C§ [1] where E is the net energy required per unit weight in a certain process of comminution; x is the factor indicating the fineness of the product; n is the exponent indicating the order of the process, and C is a constant related with the material, units chosen, etc. H exponent n in the above equation is replaced by numerical figures 2, 1, and 1 1/2, the integrated form of the general equation leads to the well known fundamental theories represented by the law of von Rittinger,' law of Kick, and the third theory of comminution by Bond, respectively. The total net energies (E) from infinite feed size to a product of size x are as follows: The net energy required in a certain process of comminution is proportional to the new surface developed according to the law of von Rittinger, to the weight or size of the bodies treated according to the law of Kick, and to the length of the new cracks formed which initiate breakage according to the theory and explanation by Bond. On a logarithmic paper, where particle size is presented on the abscissa and energy consumption on the ordinate (see Fig. 21, all three relationships are represented by straight lines. The slope m of the line according to the law of von Rittinger is equal to -1.0; of Kick, 0; and of Bond, -0.5. Experimental evidence in favor of the law of Rittinger has been presented, e.g., by Gross and zimmerley5 on quartz crushed in a drop weight crusher and evaluated for surface by the method of dissolution, by Dean on magnetite crushed by a similar method and evaluated for surface by the determination of coersive force, by piret7 and co-workers on a group of minerals crushed again by a similar method as well as by compression and evaluated for surface by permeability and gas adsorption methods, and by schellinger8 on a group of minerals ground in a calorimetric ball mill and evaluated for surface by gas adsorption. Experimental evidence in favor of the law of Kick seems to be scant in the field of comminution. On the other hand, in the field of mechanical engineering Kick's law seems to be of fundamental nature in processes such as cutting, pressing, shaping, and rolling of metallic substances. Experimental evidence in favor of the third theory has been provided by Bond." To a large extent, data are based on the vast amount of grindability tests performed in the laboratories of Allis-Chalmers Manufacturing Co. In addition to the devoted proponents of one or the other of the basic theories listed above, certain investigators have indicated that one of the theories might be applied for a certain range of sizes, while another theory might be used for other sizes. In a discussion of a paper by Bond," Dobie" presented a statement at the International Mineral Dressing Congress in London (1952) indicating that 1) for large particles, the law of Kick was approximately correct; 2) for finer particles, von Rittinger's suggestion was nearer to the truth; and 3) Bond's new

Jan 1, 1961

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By F. C. Holden, R. D. Buchheit

In the course of studies made on the Ti-Cu alloy system,' particles identified visually as TiH were encountered unexpectedly in a specimen of high-purity Ti-0.8Cu alloy. The particles did not appear immediately after preparation, but following-storage in a dessicator for several days. Since the alloy had been vacuum annealed to a low hydrogen concentration (19 ppm by vacuum-fusion analysis), the appearance of the TiH particles was suspected as a surface contamination effect. A specimen of a Ti-0.8Cu alloy had been annealed 2 hr at 790°C and water quenched, to produce the single-phase equiaxed a structure. The metallo-graphic sample was ground through 600X paper, rough-polished on a high-speed wheel with a mixture of alumina and chromic acid, awLhish-polished on a slow-speed wheel. Disturbed metal layers were removed from the final surface by alternately etching with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution and polishing on the slow-speed wheel with fine alumina. The final surface was swab-etched with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution, rinsed in tap water, and dried in a stream of filtered air. The micro-structure, shown in Fig. 1, was composed of equiaxed a grains without any trace of second phase. After storage in a dessicator for 3 days, the appearance of small particles in the structure became evident (see Fig. 2). After 7 days of storage, the particles were more distinct, and in some grains, began to appear as elongated particles. The specimen then was etched a second time (without repolishing) to produce the structure shown in Fig. 4. On the basis of micro- structural observation, the line markings were identified as TiH; attempts to obtain diffraction patterns from the surface for positive identification were not successful. That the structure is a surface effect was demonstrated by grinding with 240X paper to remove the surface layer. The surface then was ground, polished, and etched using the procedures described previously. The same observations were made: the freshly prepared surface was devoid of any second phase, whereas the particles again appeared after several days storage. The same effect has been observed in other a-stabilized titanium alloys, including a high-purity Ti-0.20 alloy containing only 16 ppm H by analysis. The effect has not yet been observed in unalloyed titanium, nor does its appearance appear to be consistent with any particular alloy system. From these observations, it is concluded that certain a-titanium alloys are susceptible to the formation of titanium hydride at the surface of metallo-graphic specimens. The hydrogen probably is diffused into the surface from a residual film of etchant decomposition products. Estimates of the hydrogen

Jan 1, 1961

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By M. H. Richman, L. M. Markowitz

MUCH of the available information on which the heat treatments of a particular steel are based is found in the isothermal-transformation diagram. Such is the case despite the fact that the usual thermal treatments involve continuous transformations, i.e., transformations which occur on cooling, rather than isothermal transformations. This rather unusual practice is continued because of the abundance of published isothermal-transformation diagrams1, 2 which are relatively easy to determine experimentally as compared to continuous-transformation diagrams.3, 4 However, this can easily lead to the production of improper micro-structures and may not allow full advantage to be taken of the inherent hardenability of a steel. A mathematical method of estimating the continuous-transformation diagram from the available isothermal data was developed by Grange and Kiefer;5 but, due to the mathematical approximations required in the calculations, the computation of continuous-transformation diagrams has been limited to individual cases and no large-scale compilation of these diagrams is available. With the present availability of high-speed digital computers, the problem of time-consuming approximations may be minimized and continuous-transformation diagrams may be constructed with the insertion of isothermal data into a basic program. It is the purpose of this report to announce the availability of such a program and compare the computed and experimental continuous-transformation diagrams for two different steels. Let us first review the method of Grange and Kiefer5 and then compare the results of the machine calculations with the experimentally determined diagrams. In order to apply this method, one requires the isothermal-transformation diagram and a set of curves representing cooling at constant rates. A section of an isothermal-transformation diagram is shown in Fig. 1 together with a cooling curve of M0F per sec. The cooling curve is constructed to start from the A1 (eutectoid) temperature if the transformation product is the eutectoid microconstituent (i.e., pearlite or bainite), from the A3 temperature if the product is primary ferrite, or from the 4, if it is proeutec-toid cementite. The cooling curve in Fig. 1 intersects the curve representing the start of isothermal transformation at a point A' corresponding to a temperature TX and a time fX. An arbitrary lower temperature To (on the

Jan 1, 1968