Search Documents

By Meredith Johnson

THE year 1924 saw little change in the production of oil and gas it either Pennsylvania or New York. In the early months of the year the price of Pennsylvania crude oil, $4.00 to $4.50 a barrel, was sufficiently high to cause operators to lay plans for rather extensive drilling opera-tions. But when, in August, the price dropped to $2.85 a barrel, there was no inducement for new work and drilling was curtailed. In spite of the curtailment, however, the combined production of the two states for the year showed a slight increase over 1923, the production being 8;859,000 bbl. in 1923, and 8,901,000 bbl.1 in 1924. The increased production was due entirely to. the continued development of flooding operations in the Bradford field, all other oilfields showing a decline for the year. TABLE 1. Production of Crude Oil in Pennsylvania and New York for the Last Ten Years a Production, Barrels Production, Barrels Year Year Pennsylvania I New York Pennsylvania I New York 1915 7,838,000 888,000 1920- 7,438,000 906,000 1916 7,593,000 874,000 1921 7,418,000 988,000 1917 7,733,000 880,000 1922 7,425,000 1;000,000 1918 7,408,000 809,000 1923 7,609,000 1,250,000 1919 8,137,000 851,000 1924 7,535,0006 1;366,0006 a U. S. Geological Survey figures. b Estimated. Much of the drilling in the southwestern part of Pennsylvania was done in search of gas. Natural gas in Pennsylvania is fast being recognized at its true worth and the increased prices allowed 'the gas companies for their product induced quite a bit of new work. The relative importance of natural gas compared with manufactured gas is shown in Table 2.2

Jan 3, 1925

By P. Stark, B. S. Lement

ACCORDING to Hanemann1 the hardness of retained austenite in a 1.7 pct C steel is increased by subsequent tempering. He reported that the hardness of this constituent increases only slightly on tempering to 300°F, rises more rapidly above this temperature, and attains the same value as the tempered martensite present in steel at approximately 480°F. The variation of hardness of both retained austenite and martensite with tempering temperature as obtained by Hanemann1 is shown in Fig. 1. Hanemann attributes the increase in hardness of the retained austenite essentially to continued formation of fine needles of martensite on tempering. Although he did not explain the actual mechanism involved, work hardening of retained austenite by the plastic deformation associated with such martensite formation appeared to be a possibility. Recently Lement, Averbach, and Cohen2 reported the existence of subgrains, about l000Å in diameter, in retained austenite and suggested that they may be delineated by a subboundary carbide. This raised the possibility that carbide precipitation might be responsible for the hardening reported by Hanemann. In view of these conflicting possibilities, an investigation" was carried out on a high purity, Fe-C alloy containing 1.7 pct C in order to clarify the nature of the phenomenon involved in the reported hardening of retained austenite. This investigation involved correlation of changes in microhardness and microstructure of the austenite as a result of tempering. Microhardness tests were made with a Tukon tester using a 25 gram load and a Vickers diamond. It was found that two groups of austenite hardness values were obtained after tempering at a series of temperatures up to 450°F, which was the highest temperature at which retained austenite regions could be identified microscopically. One group represents a high hardness level which in-

Jan 1, 1955

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By Edward Keller

Someone some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2 g. of copper) measured out for the electrolytic deposition; in the other method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 1, 1914

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By William L. Russell

A new instrument for measuring bulk and grain vol-urnes is described, and compared in accuracy with two modifications of Nutting's method, All three methods are reasonably fast, and in all three the probable error in the determinations of bulk volume can be kept down to about 0.1 to 0.2 per cent. INTRODUCTION The new pycnometer described in this paper is designed to give speed without sacrificing accuracy. Some time ago Russell1 described a somewhat similar appa-ratus; however, the instrument described in the present paper is more accurate. Nutting' designed the pycnom-eter shown in Fig. 1 (A and B), and Pirson3 has shown points like those of Fig. 1-D. The procedure described in this paper for using Nutting's pycnometer has been modified from that used by Nutting. CHOICE OF LIQUIDS The best liquids for measuring grain volumes are hydrocarbons or chlorinated hydrocarbons which evaporate slowly. Trimethylbenzene or mesitylene, triethylben-zene, carbon tetrachloride, and tertalin have been used for this purpose. Any of these liquids or mercury may be used for measuring bulk volume. PREVENTING ERRORS DUE TO INVASION OF LIQUID Errors due to the invasion of the porous, permeable bulk samples by the liquid of measurement may be prevented or greatly reduced by using mercury, by applying an impervious coating, or by soaking the bulk samples in the liquid of measurement until bubbles cease issuing from them. Errors are produced only by the invasion of the samples which occurs between movement when the samples are weighed in air and the moment the weight of liquid displaced by the sample in the pycnometer is determined. No error is produced by varying degrees of filling of the pore space of the samples by the liquid of measurement. The excess liquid should be wiped from the samples immediately before the weight in air W1, is determined, and they should be placed in the pycnometers immediately. OPERATION OF NEW INSTRUMENT The new pycnometer is shown in Fig. 2. It consists of two glass parts which fit together at a ground glass joint. The spaces J and D are connected by fine glass tubes E, and the space J must be larger than the space D by at least the volume of the largest sample to be tested. The projections H afford a grip for twisting when the two parts tend to stick together. The position of the sample in mercury is shown by I, and in other liquids by M. F is a permanent mark on the glass, and G is a tem-Some marker. In order to determine the position at which G should be placed, invert the instrument so that A is at the bottom, and fill space D. Place the cub K

Jan 1, 1958

By George A. Roberts, Robert F. Mehl

WHEN austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.1 This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced,4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ae1.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. EFFECT OF INHOMOGENEITIES ON REACTIONS NEAR Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously;1,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional quantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a "fine-grained steel." These steels can be compared at the same grain size by heating C to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By L. Adler

Analysis of a mine roof can be based on fixed-end beam behavior. The author here analyzes the effects of zero restraint at deflecting beam supports. Formulae are given for determining permissible support deflections. Analysis of a mine roof in a bedded deposit usually follows the assumption that the behavior of the roof is analogous to a beam with both ends fixed. Yet it is recognized that the end restraint itself varies with the thickness of cover, so that at shallow depth the restraint is minimum, and at great depth, maximum.' Consequently, an analysis on the basis of fixed ends or full restraint represents only one extreme in the possible range of conditions. Since the actual amount of restraint is difficult to ascertain, a more rational approach is to consider the two extreme cases of end restraint. Such situations regarding uncertainty of the restraining effects of supports are not uncommon in structural analysis, and are handled in a like manner.' Since previous studies9)4 have dealt with full restraint, this paper will analyze the effects of zero restraint at deflecting beam supports. In such a case a mine roof with several intermediate supports becomes analogous to a uniformly loaded continuous beam on simple supports, as shown in Fig. 1A. Such a structure is statically indeterminate to a degree equal to the number of intermediate supports, n. Therefore, with the three equilibrium equations, n additional equations are needed. A number of methods exist to analyze this problem, but The Theorem of Three Moments is Simplest. The continuous beam is divided at each support into a sequence of simply supported single span beams, with the unknown end moments, as appears in Fig. 1B. Continuity requires that the common ends of adjacent beams have the same slope (Fig. 1C). eiB= B(i+l)~= ei(i+l)and MiB= Mti+I)A= Mi(i+i). [1I A Glossary of all terms is given in Table I. Furthermore, if we first consider that the supports do not deflect, the slope at a support is the sum of the slopes due to each of the individual loads shown in Fig. 2, yielding:

Jan 1, 1961

By James Douglas

In discussing the waste upon which hinges, or is supposed to hinge, so largely the preservation of our national resources, the conclusions reached would be more reliable if actual experience were consulted, and fewer deductions were drawn from general statements, which are often the product of the imagination. It cannot be questioned that the value of by-products has .not been sufficiently appreciated by us, and that our tardiness in recovering the useful ingredients of the escaping gas of our coke-ovens is one of the most glaring instances of shortcoming in that direction. And yet even for that sin there is some palliation in the immature condition of affiliated industries. I presume that it is admitted, without argument, that, except under very exceptional conditions, all the elements cannot be recovered from most of the ores or natural products which we treat. While it is a shame that the by-products from our coke-ovens should be dissipated, Edward W. Parker's report to the U. S. Geological Survey for 19061 supplies a fairly good excuse in justification of this appalling waste. He says (pp. 773 to 774.): " What has been already commented on in previous reports about the slowness of manufacturers to change from the better known but wasteful beehive practice to the by-product recovery method of coke manufacture is particularly emphasized in the statistics presented in this chapter. For it would appear from the table following that the construction of by-product ovens had about come to a standstill, especially when the records for the preceding five years are taken into consideration. At the close of 1901, when there were only 1,165 by-product ovens completed in the United States, there were 1,533 in course of construction, 498 of which were completed during the following year. At the close of 1902, 1,346 retort ovens were building, 293 of which were added to the completed plants in 1903. At the close of 1903, 1,335 new ovens were building and 954 of these

Jan 1, 1910

By A. R. Troiano, R. F. Hehemann

The influence of partial decomposition to high temperature bainite on reaction kinetics at a lower temperature has been studied in two alloy steels. Reaction at the lower temperature is retarded by the prior treatment, and the extent of decomposition may be reduced. Interpretation of these results is based on a mechanism involving a limitation in the nucleation and growth of bainite plates. OF the major transformations in steel, the characteristics and general behavior of the bainite reaction are probably the least understood and appreciated. Limitations of space preclude a critical evaluation of the present status of the bainite transformation in this presentation; however, such a treatment will shortly appear elsewhere. Only the salient features pertinent to the present investigation will be introduced briefly here. Although the reaction curve for the formation of bainite is similar to that for a nucleation and growth process, other kinetic features are more in keeping with the martensitic mode of transformation. A definite temperature exists above which austenite will not transform to bainite.1-5 his temperature, which has been designated B., is determined by the composition of the austenite. Unlike other nucleation and growth processes, the amount of austenite transformed to .bainite is a function of reaction temperature. The extent of decomposition increases from 0 at H. to 100 pct at some lower temperature.' , This lower temperature will be designated B1 and appears to be relatively insensitive to austenite composition.% 5 The similarity in the effect of reaction temperature on the bainite and martensite transformations serves to emphasize the close connection between these two decomposition processes. Austenite decomposition in the bainite range proceeds without partition of the alloying elements.8-11 Partition of carbon has been proposed" primarily on the basis that partial transformation to bainite lowers M, and increases the amount of austenite retained at room temperature. Carbon enrichment resuslting from such partition has been employed to explain the influence of reaction temperature on the extent of decomposition.'" It should be noted, however, that no enrichment has been detected experimentally in high carbon steels.1,14,15 Lattice-parameter measurements of retained austenite in steels containing 0.3 to 0.4 pct C have indicated carbon enrichment, 3,10-18 although the split indicative of a high carbon martensite has not been reported. Carbon enrichment, if it does occur, must be highly localized around the bainite plates. Therefore, carbon enrichment does not account for the influence of temperature on the progress of the bainite reaction."' Thermal history is known to influence the martensite transformation through stabilization.20,21 No similar phenomenon in the bainite transformation has been reported. Materials and Procedure Two triple-alloy steels were chosen for this investigation. Their compositions were as given in Table I. These steels were chosen because the pearlite reaction did not interfere with the bainite reaction. Steel K was received in the cast condition and forged from 2 in. square bars to 1/2 x1 3/4 in. plates. The 4340 was received as 11/4 in. hot-rolled rounds. Both steels were homogenized in vacuum for one week at 2300°F in order to minimize segregation. A quenching dilatometer similar to that described by Flinn, Cook, and Fellows" was employed for the kinetic measurements. Dimensional changes were detected by a differential transformer coupled with a high speed recorder. The dilatometer was mounted so that it could be transferred to any one of three furnaces: a nitrogen-atmosphere austenitiz-ing furnace and two salt-bath furnaces for isothermal transformation. Dilatometer specimens were 1/32 x 1/4x 1/2 in. with a gage length of 1.4 in. All specimens were nickel plated in order to minimize decarburization during austenitizing. The austenitiz-ing conditions consisted of 10 min at the temperatures given above. Austenitizing temperatures were controlled to 210°F and transformation temperatures to ±3ºF. The precision of the dimensional measurements was estimated to be ± 5 x105 in. per in. Results and Discussion Isothermal Transformation: The characteristics of the isothermal bainite reaction will be described

Jan 1, 1955

By Louis L. Stott

It is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halskes reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys. PRopeRties of Beryllium A comprehensive summary of the available data on the properties of beryllium is given in " Gmelius Handbuch der Anorganischen Chemie7." The metal is steel gray in color. A fractured surface exhibits a bright luster, which does not appear to change with long exposure to air, probably because of a thin, transparent protective oxide coating. The specific gravity is approximately 1.8. Although there is no recorded actual determination of Young's modulus of elasticity, it has been estimateds, according to Fessenden's law, to be 30,000 kg. per sq. mm., or about 30 per cent higher than steel. Beryllium appears to have an electrical conductivity approximately 1/12 that of copper. The physical constants as available in the literature are given in Table 1. One of the outstanding properties of beryllium is its great affinity for oxygen, nitrogen, sulfur and carbon. One gram of beryllium takes up 1.774 grams of oxygen and will liberate approximately 15.23 kilogram-calories in the combination. The metal apparently reacts with all known oxides at high temperatures; in fact, beryllium will alloy with thorium and zirconium if melted in crucibles of their oxides. The true physical properties of beryllium are still somewhat in doubt, since very small amounts of impurities appear to cause a large variation

Jan 1, 1936

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1919, to Nov. 10,1919. Carl A. Allen, Salt Lake City, Utah. W. G. Mitchell, Montreal, Canada. M. M. Altmayer, Paris. Henry S. Munroe, Litchfield, Conn. A. E. Bellis, Major Ord., Springfield J. S. Negru, New York, N. Y. Armory, Springfield, Mass. Edmund Newton, New York, N. Y. R. S. Botsford, New York, N. Y. A. W. Newberry, Cleveland, Ohio. Henry S. Burnholz, Monterrey, Mexico. C. C. O'Harra, Rapid City, S. D. D. E. A. Charlton, New York, N. Y. Fred S. Porter, Philadelphia, Pa. C. C. Colburn, Denver, Colo. Donald A. Powell, Columbus, Ohio. C. V. Corless, Coniston, Ontario. Thomas T. Read, Washington, D. C. I. N. Daily, Seattle, Wash., W. L. Remick, Chrome, N. J. E. V. Daveler, Butte, Mont: Hallet R. Robbins, San Francisco, Calif. John Davis, Fairbanks, Alaska.' Milnor Roberts, University Station, E. W. Engelmann, Salt Lake City, Utah. Seattle, Wash. M. E. Erdofy, New York N. Y. Thos. S. Roberts, Lakehurst Proving W. F. Ferrier, Toronto, Canada. Grounds, N. J. H. A. Fisher, Pittsburgh, Pa. George B. Rodgers, Dobbs Ferry, N. Y. Walter Fitch, Sr., Eureka, Utah. John C. Rogers, Copper Cliff, Ontario. C. D. Grier, New York, N. Y. Joseph L. Rosenmiller, Bethlehem, Pa. A. Hibbert, London. . C. J. Saville, Portland, New South Wales. John E. Hodge, Minneapolis, Minn. W. A. Scheuch, New Jersey. W. E. Hopper, Newark, N. J. S. B. Shutts, Lynchburg, Va. M. R. Hull, McGill, Nev. E. W. Smith, U. S. Army. A. W. Ibbett, Trinidad, B. W. I. S. J. Speak, London. A. O. Ihlseng, Joplin, Mo. John. B. Stewart, Santiago de Cuba, Sherwin F. Kelly, Lawrence, Kans. Cuba. R. G. Knickerbocker, Logansport, Ind. S. A. Taylor, Pittsburgh, Pa. .M. H. Kuryla, Eureka Colo. Karl Thomas,' New York, N. Y. F. G. Lasier, Detroit, Mich. F. L. Torres, Eureka, Nev. David Lasuer, Elizabeth, N. J. Henry Traphagen, Toledo, .Ohio: H. H. Lauer, Allentown, Pa. W. D. Van Doren, Ottawa, Canada. J. Whitney Lewis, Care First Nat'l Bank, J. A. Vernon, Newport, R. I. Tulsa Okla James Wilding, San Francisco, Calif. James W. Love, Knoxville, Tenn. D. J. Williams, Butte, Mont. Dorsey A. Lyon, Washington, D. C. Harry J. Wolf, New York, N. Y. M. E. Martiner, Boston, Mass.. Dwight E. Woodbridge, Duluth, Minn. Benj. L. Miller, Bethlehem, Pa. Percy E. Wrighn, Seattle, Wash. W. G. Miller, Toronto, Canada. F. Yamada, Tokyo, Japan.

Jan 12, 1919

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921