Search Documents

AlFred JamEs," London, Eug.:—I thank you, gentlemen, for Sour kind invitation to address you. It is a very great pleasure for me to be here at your annual meeting, and, although I have been a member since 1894, this is the first opportunity I have

Jan 1, 1909

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By T. P. Floridis

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

PUBLIC hearings began before the Committee for Reciprocity Information on May 24, 1950, for the purpose of unearthing data and opinion that will be helpful in the forthcoming reciprocal tariff and other trade-barrier negotiations at Torquay, England, on September 28th of this year. The conference this fall will constitute the "third round" of tariff negotiations under the General Agreement on Tariffs and Trade concluded at Geneva in 1947. The United States plans to negotiate with 17 other countries on possible tariff modifications on various articles all the way from baby carriages and bottle caps to lead and zinc-bearing ores. On May 31, June 1 and June 2, spokesmen appeared before the Committee for Reciprocity Information on behalf of the domestic lead and zinc mining industries. Producers of these metals protested the inclusion of paragraphs 391 (lead-bearing ores, dust and mattes), 392 (lead bullion, lead in pigs and bars, and scrap lead), 393 (zinc-bearing ores of all kinds), and 394 (zinc in blocks, pigs or slabs, and zinc dust) of the Tariff Act of 1930, as amended in the list of articles to be considered for possible tariff concessions at Torquay. It was pointed out that although operating costs have more than doubled since 1939 tariffs on these metals were actually higher in that year than at present. This, coupled with the detrimental effects of the recent series of devaluations, has sounded the death knell for a substantial number of domestic lead and zinc mines-a most undesirable development in the face of the ominous international situation, according to these spokesmen. It was urged that higher rather than lower tariff rates are needed on these metals. The opinion was expressed that it was inconsistent to foster a high living standard in our western areas and then, once it is attained, to undermine that condition by minimizing the protection that was partly responsible for it. The main theme of some arguments implied that although every effort should be made to close the "dollar gap" abroad, serious consideration must be given the methods employed lest our national security position be jeopardized in the process. The House Committee on Foreign Affairs completed hearings on H. J. Res. 236, to provide for United States membership and participation in the International Trade Organization. Hearings began on April 19th and ran for over five weeks. Many witnesses from industry and government presented voluminous testimony, which will not be available for public distribution for several weeks. However, it is no secret that the most controversial provisions of the Draft Charter of the ITO are: (1) Article 17 (Chapter IV on Commercial Policy) which would obligate members to negotiate for the reduction of tariffs and the elimination of trade preferences; (2) Article 20 which would prohibit the use of quantitative restrictions for protective purposes; (3) Article 16 which promulgates rules to implement the principle of non-discrimination in international trade; and (4) provisions permitting the use of protective measures for promoting economic development, particularly in backward areas, even though such provisions are inconsistent with those of the three articles cited above. United States membership in the International Trade Organization is essential to the successful operation of that body in view of this country's position as the economic giant in the present international trade pattern. Many countries are reluctant to take any action toward the ratification of the charter until it is known what course America will pursue. However desirable or undesirable the ideal of free multilateral trade may be it is unlikely that this Government's participation in the ITO will materialize soon. Advices in Washington indicate that H. J. Res. 236 will not be enacted during the present session of Congress. The legislative pattern designed to secure Congressional approval of the ITO is similar to that of the St. Lawrence Seaway project. The Seaway project was pending in treaty form for several years before the Foreign Relations Committee of the Senate and when the Administration decided to incorporate this project into bill form it was found that, while it passed the House promptly, the Senate decided to pigeonhole it because of the obvious intent to circumvent the constitutional prerogative of the Senate to advise and consent to the ratification of treaties. The ITO bill may be slated for a similar fate. It is deemed essential by western Senators and Congressmen that the present session of Congress enact some form of mining legislation before its adjournment, now set for July 31st. These legislators from prominent ore-producing states do not desire to return to their home areas in the fall emptyhanded. Aside from that, it is entirely superfluous to reiterate the necessity for maintaining a healthy domestic mining industry as a bulwark against a sharp rise in the temperature of the "cold war". Now that S. 2105 has failed a new bill is taking shape in the Senate Interior and Insular Affairs Committee. It is similar in language to H. R. 8221 (to encourage the conservation and development of the mineral resources of the United States) reported by the House Public Lands Committee on May 3, 1950, but so far has failed to receive approval of the House Committee on Rules. There are some qualified observers in high circles in Washington as well as in the mining industry who favor a tax incentive program to stimulate investment in mining enterprises, as opposed to a conservation and exploration program. The Bureau of Mines and the Treasury Department have undertaken a joint study to determine the need for modification of the tax laws as they apply to mining. The study is scheduled for completion before the end of the year, and appears to be supplementary to the investigation initiated by the National Minerals Advisory Council which culminated in the submittal of recommendations to the Secretary of the Interior in December 1949. The "cold war" is largely responsible for the increased demand for metals. Stock-pile purchases and heavy industrial demand due to military needs distort markets and disrupt normal price trends. Such activity has an unhealthy influence on metal production, luring some producers into a state of dependency on the continuation of this condition. When stock-pile objectives are met sometime in the future purchases must then come to a halt unless international "fireworks" are touched off. It can only be hoped that technological improvements and further mechanization of mines coupled with the stimulus of a rising population will offset the anticipated drop in industrial demand and cessation of stockpile purchases when the international crisis abates.

Jan 7, 1950

By L. D. Jaffe

THE data recently published1-" on heat treatment of titanium alloys have not been readily systematized into an overall picture. When the ß titanium phase transforms isothermally at low temperatures, the hardness follows a typical age-hardening pattern, going through a peak as schematized by the "hardness" vs "time of isothermal transformation" coordinates of Fig. 1. As the temperature is raised, the peak will decrease in height and occur at shorter times; slowing must however take place as the /3 transus is approached. The brittle microconstituent in the region of peak hardness has been termed /3'. Its structure is still undetermined but it is clearly a transition stage from soft /3 to the £ + a that is found at the right of the peak. On continuous cooling, high cooling rates correspond to short times on Fig. 1; abscissa labeling has been added accordingly. Extremely rapid cooling will retain soft /3; very slow cooling will precipitate soft a; intermediate rates give hard 8'. Increasing distance from the water-quenched end of a Jominy hardenability bar corresponds to slower cooling (right on Fig. I), but the range of cooling rates covered by a Jominy bar is only a small portion of that shown in the figure. The p-stabilizing alloying elements retard the transformation process, moving the material to the left on Fig. 1. A lean alloy is harder water-quenched (P') than air-cooled (/3 +a); a rich alloy is harder air-cooled (/3') than water-quenched (/3). Examples of the position of various compositions with respect to the curve, based on limited data in the literature, are given at the top of the figure. Oxygen and carbon accelerate the transformation process, moving the material to the right on Fig. 1. If an alloy quenched quickly enough to retain soft /3 is reheated below the £ transus (tempered), it ages, going through a hardness maximum as time increases (moving right on Fig. 1). Material which after cooling from the /3 range lies on or right of the hardness peak, will move still further right on tempering, and so soften. Since the rate of the tempering (aging) reaction increases with temperature, the figure also may be used to represent the variation in properties with tempering temperature, at short tempering times. The simple picture given here neglects martensite transformation, as well as differences between decomposition products of /3 formed by direct isothermal transformation and those formed by quenching and tempering. It may nevertheless be of use as a guide for practical heat treatment and for further research.

Jan 1, 1955

By F. D. Rosi

IT was recently shown1 that slip bands can be observed in bent germanium crystals after deformation, by means of etch pits along the slip traces. It is the purpose of this note to show how chemical etch pits can also be usedto examine the appear- ance of slip bands in silicon, as well as other deformation markings. A 30 ohm-cm, p-type single crystal bar, 2x1/4x1/8 in., was plastically bent at approximately 1200°C in a vacuum of 1x10-5 mm Hg. The axis of the crystal was coincident with a <III> direction, and the surface normal to the axis of bending was within 4" of a (110) plane. Prior to the deformation, the (110) surface was mechanically polished with

Jan 1, 1958

By R. E. Frounfelker, W. M. Hirthe

INVESTIGATORS in the areas of plasticity, crystal growth, and stress analysis have a need for crys-tallographic data such as the interplanar angles. This information is utilized in the form of a stereo-graphic projection from which orientation determinations can be made. Calculations of mechanical properties, such as the critical resolved shear stress, require values for the angles between directions as well as the interplanar angles. Only a limited amount of this data is available for tetragonal crystals. The equations for these angles are relatively simple but because of the large numbers of angles involved and the infinite number of structures that could be investigated, it was decided to program these calculations on a high speed digital computer. The angle, 8, between two crystal planes (h1 k1 l1)

Jan 1, 1962

The failure of finely-divided sulfide particles to respond to flotation has resulted in a significant loss of our natural resources. As mentioned by Professor Arbiter, the overall recovery of copper from porphyry copper ores is generally between 80 and 85 percent. The recovery of copper sulfides from these ores is about 90 percent, the difference in these recoveries being due to failure of oxide copper minerals to respond to flotation. The 10-percent loss of sulfide copper has not been studied. Losses are known to be in the fractions finer than 74 microns, but the sizes that are not responding to flotation have not been established. In the case of molybdenite, however, it is known that particles finer than about five microns are not recovered. Work in other systems, notably the hematite-quartz system, has shown that good flotation of very fine particles from natural ores is possible (1, 2). The size distribution of one ore that was researched is given in Table 1, and as shown, approximately 50 percent of the ore was finer than 10 microns. Flotation experiments were conducted with this ore, which contained 45 percent iron, utilizing octyl hydroxamate as collector and without any desliming (1). The results of these experiments are presented in Table 2. From the standpoint of mechanisms of collector adsorption, similarities exist between those occurring in the hydroxamate-hematite system and many xanthate-sulfide systems. .This is, multilayers of ferric hydroxamate are present on hematite under flotation conditions (1,3).

Jan 1, 1979

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By J. D. Mooney, D. L. Darnell

The accompanying chart has been drawn for the convenicncc of engineers as&apos; a means of quickly determining the correct number of plies of conveyor belts operating under specific conditions. The calculations are based on the average safe strength (factor of safety, 15) of the various standard rubber conveyor belts. The calculations assume maximum loading conditions; that is, the belt is considered as carrying the greatest load that it will handle without spillage at ordinary belt speeds. This not only produces the most economical operating conditions, but also the maximum tension in the belt. The chart is a graphical representation of the formula: Where, p = kg W(L + 10H) p = the correct number of plies k = a constant, depending on the type of drive g = the weight &apos;in pounds per cubic foot of material handled W = the width of the belt in inches L = the length of the belt in feet (approximately twice the center distance). H = the difference in elevation between the head and tail pulleys, in feet. For a simple drive, with a bare pulley, k = ----1 For a simple drive, with a rubber-lagged pulley, k = --- 1 For a, tandem drivej with bare pulleys, k = 1/375.000 For a tandem drive, with rubber-lagged pulleys, k = ---1 The chart is drawn for a simple drive, with a bare pulley (k — =e)1 ; therefore, the number of plies obtained from the chart should be multi- &apos; plied by the factor 0.83 or 5/6 for simple, lagged drive; the factor 0.67 or 2/3 for tandem, bare; and the factor 0.55 or 11/20, for tandem, lagged. The formula p = kgW(L + 10H) has been developed mathematically

Jan 1, 1916

By H. J. Levinstein, W. H. Robinson

A method of chemically polishing silver for metal-lographic examination has been developed. The samples are prepared by polishing on 0, 2/0, and 3/0 paper. They are then polished on 600 micro-cut paper, followed by a final mechanical polish on a cloth containing 5µ diamond paste. The samples are then chemically polished in a solution of 100 cc of saturated chromic acid and 5 cc of a 5 pct HC1 solution. The chemical polishing is performed by swabbing with a cotton ball saturated with the solution. During the chemical polishing, the sample is rinsed frequently in running water. Polishing in this manner for 5 min is sufficient to remove the strained material from the previous polishing operations. The amount of material removed is approximately 4µ/min. The surface obtained is flat and free of pits. Fig. 1 is an interference micrograph of a silver surface polished by this technique. If the solution employed is of improper HC1 content, an interference color film will form on the sample. This film can be removed either by swabbing with a cotton ball saturated with ortho-

Jan 1, 1962

By Evan Evans

HOME-TOWN boy makes good in a i1 big way in the home &apos; town, expresses concisely the accomplishments of Evan Evans. Born in Coaldale, Pa., in 1895, within sight of the mine head-frames and cleaning plants dotting the Panther Creek Valley, his whole life has been intimately associated with the strip and underground mines of this valley. One of the world&apos;s largest mineral deposits exists in the confines of the Panther Creek Valley and mining has been in progress for 125 years. Despite this long period of mining activity, two thirds of the coal in the valley yet remains to be mined. The Lehigh Navigation Coal Co. is the operating company.

Jan 1, 1947

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport&apos;s operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport&apos;s operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By R. W. Vander Laan

Conneaut has a long and illustrious history as a major Great Lakes port for coal and iron ore. The first dock was built in 1892 for unloading iron ore from the Mesabi Range for shipment to the Pittsburgh steel mills via the Shenango & Lake Erie Railroad, later to become the Bessemer & Lake Erie Railroad. The Pittsburgh & Conneaut Dock Company was incorporated in 1893. The world&apos;s first Hulett automatic ore unloader was constructed at Conneaut in 1899. Steam operated, it was the model for the giant electric Huletts used today, named after its inventor, George Hulett, who was a Conneaut resident.

Jan 3, 1974

By L. G. Austin, R. R. Klimpel

This communication points out that serious errors exist in some current treatments of the random fracture of solids, including the prior treatments by Klimpel and Austin, Gilvarry, and Gaudin and Meloy. The problem considered in all of these papers is: what cumulative weight versus size distribution is expected for the fragments produced by fracture of a particle? The basic assumption made is that fracture surfaces propagate in random directions from weak flaws in the solid (these weak flaws being activated to fracture by applied stress), with the activated weak flaws distributed at random spatially within the solid. The previous treatments considered fracture in three dimensions, and all use similar physical models, although the mathematical techniques were somewhat different. We first noticed that these treatments were in error when we attempted to reduce the equations developed to the simple case of fracture of a one-dimensional particle, e.g. a long, thin fiber which breaks along its length. For this simple case, it is readily shown that the assumption of random fracture leads to the expression P(V) = (r/Vo) (1-V/Vo) r-1 dV (1) is the probability of occurrence of a fragment of length within the range V to V + dV; V being length dimension, from r random fractures passing through an original size of Vo to produce r + 1 fragments. This equation agreed with the one-dimensional form of an equivalent equation in the original Klimpel-Austin treatment. However, in this treatment it was then stated that, "The fractional weight below size V is [ ]

Jan 8, 1968

By M. E. Lombardi

Discussion of the paper of AI. E. LOMBARDI, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 2109 to 2114. C. D. KEEN, Shreveport, La.-Did Mr. Lombardi include in his figures the purchase price of the property? M. E. LOMBARDI, Berkeley, Cal.-No. C. D. KEEN.-Suppose I pay $1,000 per acre for it, and in four or five years it is worked out. M. E. LOMBARDI.-That is a question of depreciation and must be added to my figures. MARK L. REQUA, San Francisco, Cal.-You say it cost $35,000 to $40,000 a year to maintain 1,000-bbl. per day production? M. E. LOMBARDI.-Yes, 1,000 bbl: a day would cost $40,000 a year to maintain.

Jan 12, 1915