Search Documents

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By C. Max Bauer

THE most important development in the petroleum industry in Montana, during 1924, was the bringing in of the Hepp well on May 12, by the Midwest Refining Co. This followed three years of active prospecting and drilling in the state by this company. The well is located 35 miles west of Billings, in Stillwater County, and makes a high-grade paraffin oil from the Dakota sand at a. depth of 3825 ft. After flowing for several months at the rate of 150 bbl. per day, the well has been shut in for lack of storage, awaiting further development in the field. TABLE 1. Production Cat Creek and Kevin-Sunburst Fields Month Kevin-Sunburst Pipe- Estimated Cat Creek Pipeline Estimated line Runs Fuel Oil Used Runs Fuel Used January 3,214 0 133,400 140 February 3,250 0 134,248 490 March 11,989 595 163,129 910 April 116,897 1,155 125,918 980 May 179,726 2,310 152,179 770 June 126,131 2,697 122,270 910 July 132,173 2,170 118,034 770 August 202,001 2,695 142,313 1,120 September 187,201 2,135 110,012 350 October 162,589 1,995 121,683 350 November 130,392 2,520 139,900 350 December 107,465 1,780 124,169 0 Total 1,363,028 20,052 1,581,255 .7,140 There are two producing oilfields in the state-the Cat Creek and the Kevin-Sunburst, which produced a total of 2,971,475 bbl. in 1924. The only other field of proved value is Soap Creek, which contains a heavy black oil and is shut in for lack of marketing facilities. Gas is produced for local use at Havre, Chinook, and Baker, and a carbon-black plant is located at Baker.

Jan 3, 1925

By C. K. Leith

WE face the postwar problem of the use of minerals as sanctions to control the armament and the re-armament of the Axis powers at the source, minerals being the raw material of armaments. That is the subject of today's discussion. It is one thing to talk about controlling minerals in the interest of rearmament, and it is another thing to put any such ideas into effect. A provision for min- eral sanctions-not by that name but under broader terms-was contained in Article 16 of the League of Nations, and an attempt was made to apply min- eral sanctions when Italy cut loose in Africa. That was a failure because the plan was badly thought out. They did not have the right minerals included in the list. Also, they did not have the machinery set up at all. Somebody said to the League of Nations: Let's apply the sanction, and it was assumed that that was all that was necessary. It turned out to be a rather sad perfor- mance. However, that certainly cannot be taken as an example of what will happen if a properly thought-out pro- gram is adopted.

Jan 1, 1944

By R. W. Freeman, L. L. Tavlarides

The experimental methods used in obtaining kinetic data for solvent extraction systems can affect the validity of the results The method of contacting the two liquids should allow for accurate determination of the surface area, hydrodynamics, and diffusional processes The appropriateness of the Liquid Jet Recycle Reactor is discussed and the modelling of the mass transfer and chelation reaction is presented The LJRR is used to investigate the chelation of copper by LIX65N in toluene from aqueous copper sulfate sulfuric acid solutions The ranges of experimental variables are Copper, 1 8-13.8 g-dm-3, sulfuric acid 0-1.6 g-dm-3, LIX65N, 0 1-1.0 mol-dm-3 Data on the initial rate of copper chelation at the interface is generated Nonlinear regression analysis shows that the following expression adequately describes the data within experimental error.

Jan 1, 1981

By D. A. Keyes

International Minerals & Chemical Corp. (Canada) Ltd. is presently exploiting by underground mining a potash-rich zone in the middle Devonian Prairie Evaporite formation near Esterhazy, Saskatchewan. Of the three main potash-bearing horizons denoted by Goudie as zones 1, 2 and 3 only the 1ower. two are present at Esterhazy and mining is confined to the lower or zone 1 horizon. The area in which the evaporites were deposited, although flanked on the west by a zone of geosynclinal deposition and tectonic activity, has been subjected to only very gentle epeirogenic activity. The sylvinite ore is coarsely crystalline and occurs in well-defined beds. The halite, sylvite and insoluble content of the ore bears a direct relationship to the lithological units, but the carnallite cuts across the beds. Local concentrations of salt produce blank spots in the ore horizon. Some of these appear to be salt-filled, post-ore channels and cracks while others have been formed by brines emanating upward from below the ore. INTRODUCTION International Minerals & Chemical Corporation (Canada) Ltd. is operating an underground potash mine near the town of Esterhazy in eastern Saskatchewan. The deposit was discovered by IMC in 1955. Subsequent drilling outlined extensive high-grade reserves, and in 1957 shaft sinking and plant construction began. Production from Yarbo No. 1 Shaft commenced in September, 1962 and quickly reached the initial capacity of one million tons of muriate product per year. Production is currently being expanded to 1.6 million tpy. The single mining level is 3140 ft below the surface at No. 1 Shaft. GENERAL GEOLOGY The Esterhazy district lies within the Interior Plains region of Canada and on the northeast rim of the Williston Basin (Fig. 1). Average dip of the rock formations in this area is about 40 ft per mile to the southwest. The potash ore occurs in the Prairie Evaporite formation of the Middle-Devonian Elk Point Group. The Prairie Evaporites are overlain by 3000 ft of Paleozoic shales and limestones and by Jurassic and Cretaceous sandstones and shales (Fig. 2).

Jan 1, 1967

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934

By Hans Lundberq

WHEN geophysical methods were first employed in the search for ore deposits and oil accumulations, it was hoped that they would provide a direct means of locating such concentrations. Magnetized needles were used long ago in prospecting for magnetic iron ore, and soon after the discovery of galvanism in about 1790 attempts were made to find concentrations of valuable minerals electrically. Evidence indicating that the early geophyeical instruments were regarded merely as improved divining or dowsing rods is to be seen in the names "mineral finders," "ore finders," etc., that were applied to them. Today, appellations of this kind raise serious doubts in informed minds as to the intelligence and integrity of individuals advocating the use of such euphemistically named methods or instruments, for experience and research have shown that, geophysical, it is never a question of directly locating a given mineral but merely of delimiting its possible occurrence.

Jan 1, 1939

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-' indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s's of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,' from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By Paul T. Allsman

1.1-1. Current Status. The history of surface mining is essentially that of mining coal, copper, and iron ores, and the nonmetallic minerals--clays, gypsum, phosphate rock, sand, gravel, and stone. Table 1.1-1 is a comparison of the estimated world production of crude metallic and nonmetallic ores and coal with that of the United States for 1964, in short tons. It includes an estimate of the quantity produced by surface mining methods. Two-thirds of the 8.8 billion tons are mined from surface, ranging from a third of the coal, half the metallic ores, and nearly all clays, stone, sand, and gravel. In the United States, production by surface methods parallels that of the world with two major exceptions: 74% of copper ore and 90% of usable iron ore are mined from the surface, whereas outside the country less than 40% of copper ore and only 50% of usable iron ore are mined from the surface. In surface mining of both metallic ores and coal, much waste is stripped, but in mining nonmetallics the ratio between waste and ore is small. Assuming that the stripping ratio for surface mining in the United States will apply equally to world production, it is estimated on a weighted basis that over 21 billion tons of waste, or a total of nearly 27 billion short tons of material, are mined annually in the world by surface methods. Data are not available to confirm the assumption for waste stripping outside the U.S., but the estimate expresses an order of magnitude that is worth noting. Table 1.1-2 shows the materials-crude ore, coal, and waste-mined by surface methods and the relation to total mined by both surface and under- ground methods in the United States during 1964. Eighty-two percent of all crude metallic and nonmetallic ores and coal was mined from the sur- face, including 82% of metallic, 96% of nonmetallic ores, and 35% of coal. Copper and iron ore comprise 83% of the metallic ores mined from the surface, and clays, gypsum, phosphate rock, sand, gravel, and stone

Jan 1, 1968

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956

By R. Schuhmann

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) In his excellent paper, Dr. Schuhmann has proposed a mechanism for conlrninution which can be utilized to explain a number of phenomena which have been observed in the size reduction of solids. The difference between the product obtained from a ball mill and from a rod mill can readily be explained by Dr. Schuhmann's hypothesis. Consider that the size distribution of the product from each comminution event is given by y; - 100 (x/ki) (1) where Yi is the cumulative percent finer than size x, ki is the size modulus, and is the distribution modulus for the single comminution event. The total product from a cornminution operation will be the summation of the products from all of the individual cornrninution events. If the size moduli from the various comminution events range from kl to kn , the size distribution of the total product will be a straight line on a log-log plot only to a particle size equal to k ,. Considering 100 volurnes of feed, the value of y for x equal to kl is Riven by where y is the cumulative percent finer than size kj, z is the number of comminution events of kind i, and vi is the volume of each particle crushed. y=z1 qv1+z2 qv2 (k1/k2) +.............zn qvn (k1/kn) (3) F or particle sizes greater than k1 7 e. 6. x = k3, the value of y will be given by k3 A y = z1 qv1 + z2bv2 + Z3uV3 + zn zn qvn (k3/kn)(4) Only when x is equal to k, will y equal 100. 'Thus, the total product from a comminution operation will be a straight line on a log-log plot strictly up to a particle size equal to kl and above that size the line will curve so that y will equal 100 for the coarsest particle or k, (see Fig. 1). The actual shape of the size of distribution curve will depend upon the relative number of conmninution events of different kinds. In the case of ball milling, the ratio kn/kl may be pite large and there will be considerable deviation at the coarse sizes in a Schuhmann plot. kIowever, the grinding action in a rod mill is such that fine particles are protected from the rods by the coarse particles. Consequently, kn/kl will be quite small and the product from a rod mill will give a straight line Schuhmann plot almost to y equal 100%. In his paper, Dr. Schuhmann also has presented a very straightforward definition of grindability derived from the basic energy equation E = Ak-a (5) where E is the energy required to comminute a material to a size modulus of k and A is a constant. According to Dr. Schuhmann, the grindability of a material is the volume of material comminuted finer than unit size per unit of energy expended, this being 1/A. For comparison of grindabilities at any size two numbers are required, both = and 1/A, and anyone tabulating grindabilities should give both of these numbers. Concerning the experimental determination of grindabilities, if the material being comminuted possesses distinct cleavage, the energy re quired for comminution is given by E = Ak-(a-y) (6) where y is small number less than = . Because of cleavage, less energy will be required for comminution. To be certain that cleavage does not affect the gindability of the material being tested, it is suggested that the method used by Dr. Charles for determining grindability be used to ascertain if the deviation exponent y is zero or finite. R. Schuhmann, Jr. (Author's Reply) Dr. Fuerstenau's interesting comparison of rod milling and ball milling

Jan 1, 1961

By Shiou-Chuan Sun

Most previous work on sedimentation of coal1 and mineral2,3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer,4 shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-division line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions.

Jan 1, 1959

By F. Habashi

Conclusive evidence is given showing that the dissolution of gold in cyanide solution follows mainly the over-all equation A similar equation can also be written for the dissolution of silver. Theoretical derivation of the velocity equation for this reaction has been obtained, which describes quantitatively the experimental facts. The equation is as follows: where [CN-] and [O2] = the concentrations (in moles/ml) of cyanide and dissolved oxygen, respectively. DcN- and Do2 = the diffusion coefficients of cyanide and dissolved oxygen; 1.83 x 10-5 and 2.76 x 10-5 cm2 sec-1, respectively. A = the surface area of the metal in contact with the aqueous phase, in cm S = the thickness of the boundary layer; varies between 2 and 9 x 10-3 cm, depending on the speed and method of agitation. Rate being expressed in g. equiv. sec-1. INTRODUCTION During recent years a number of papers have been published on the kinetics of dissolution of gold and silver in cyanide solution.1,6 The authors agree that the rate of dissolution is diffusion-controlled, but disagree regarding the mechanism of the reaction. Some authors'-3 support the Bodlander equations: The apparently conflicting results, when critically reviewed, are concordant and lead to the conclusion that the proper equation for the dissolution reaction should be only Eq. 1. This conclusion is based on the following facts: 1) For every 2.2 equivalents of metal dissolved one mole O2 was consumed. 2) For every 1 equivalent of metal dissolved, 2 moles of cyanide were consumed.' 3) Hydrogen peroxide is formed during the dissolution of gold or silver, and for every 2.2 equivalents of metal dissolved, one mole H2O2 was produced.1,2 The fact that Kudryk and Kellogg4 did not detect H2O2 during the dissolution of gold should not throw doubt on the many affirmative reports of other investigators. Lund2 has shown that depending on the crystalline nature of the silver surface, (e.g. method of etching the sample) H2O2 may undergo catalytic decomposition heterogeneously according to: Further Kudryk and Kellogg4 carried out their experiments in the presence of 0.5% KC1 to achieve a greater electrolytic conductivity, and Matsudaira7 has shown that H2O2 is catalytically decomposed (homogeneously) in the presence of C1- ion in alkaline solution. 4) Experiments carried out by Boonstra8 and Lund2 showed that the dissolution of gold and silver respectively in KCN + H2O2 in the absence of oxygen was a slow process. Thus the reaction takes place to a minor extent only. Further kinetic studies showed that: 1) The rate of dissolution depends on the surface area of the metal in contact with the liquid phase, thus indicating that the process of dissolution is a heterogeneous process. 2) The rate of dissolution depends on the speed of stirring,5,6 thus indicating that the process is controlled by a physical phenomenon.

Jan 1, 1967

By R. C. Padfield

Experience over a 3-year period in Bethlehem Steel Corporation's plants has demonstrated the reliability of open-hearth roofs of bonded sprung-arch constructzon with burned basic brick. The design principles lor constructing these roofs include a minimum hot-strength requirement for the basic brick, expansion allowances that extend the full roof thickness, structural members to control arch contour, and a specified minimum roof rise. The greater stability of bonded roofs is explained in terms of the basic stress patterns of ring constrution and bonded construction. PRIOR to the development of successful sprung-arch roofs of basic brick, the majority of open-hearth furnaces in the United States were operated with sprung-arch roofs built of silica brick. Although many silica roofs used on open-hearth furnaces were ring-arch construction, Bethlehem Steel Corp. used bonded-arch construction because of its greater stability. In ring construction, each ring of brick is separately keyed and comprises an independent arch with the straight joints between rings traverse to the longitudinal axis of the furnace. In bonded construction, the bricks are laid in rows starting from the skewbacks so that the straight joints run parallel to the longitudinal axis of the furnace. Each brick in a given row is laid so that it spans the joint between two bricks in the row beneath it. Thus, the transverse joints across the arch are broken and the arch rings are thereby interlocked or bonded. When basic roofs were first being developed, the basic brick that were available had low hot strength. Such brick could not be safely used in sprung-arch construction without some means of suspending them. With the development of higher firing techniques by brick manufacturers and the recently introduced direct bonded bricks with high hot strength, the use of burned basic brick in sprung-arch roofs became feasible. The availability of high hot strength basic brick coupled with the potentially lower cost and proven stability of bonded construction prompted Bethlehem's Research Department to study the possibility of using basic brick in bonded roofs. With the full cooperation of plant ceramic engineers and open-hearth superintendents, particularly in 3 years of fur-nace trials, we developed the design criteria for bonded roofs and the corresponding property requirements for the basic brick that are discussed in this paper. DESIGN PRINCIPLES OF SPRUNG-ARCH BRICK ROOFS Stresses in Fixed Arches. A sprung-arch open-hearth furnace roof is generally built on rigidly held skewbacks. The constraint of the fixed support at each end adds a bending moment to the horizontal and vertical reactions at the ends of the arch. Fig. 11 shows the positive direction of forces acting on an arch fixed at both ends. Fixed arches can be analyzed when the members are continuous and have elastic properties. However, brick are inelastic, and arches built with individual brick segments cannot carry tensile stresses. Therefore, for practical solution of brick arches, empirical formulas have been derived from elastic theory that place design restrictions on arch dimensions to avoid development of tensile stresses. McDowell2 cites three main conditions for stability in sprung brick arches: 1) the thrust line of the arch should be maintained in the middle third of the thickness to avoid tensile stresses and resulting open joints in inner and outer curves of the arch; 2) the angle between the line of thrust at any joint and a line perpendicular to the joint must not exceed the angle of repose between brick; and 3) the maximum pressure at any point must not exceed the strength of the arch materials at furnace operating temperatures. The first and third conditions are particularly important in designing sprung-arch basic roofs because of the comparatively low hot strength of basic brick. According to McDowell's equation, if the thrust line is maintained within the middle third of the arch thickness, the unit pressure is obtained as follows: where p = unit pressure in psi, F, = resultant thrust normal to skewback in pounds per foot, t = arch thickness in inches, and z = distance in inches of thrust line from arch axis. When the resultant thrust normal to the skewback acts along the arch axis, z equals zero and unit pressure is simply the thrust divided by the cross-sectional area. If the thrust line moves to the limits of the middle third of the arch thickness, beyond which tensile forces would develop, z then equals one-sixth of the arch thickness and the unit pressure is double that when the thrust line is acting

Jan 1, 1968