Search Documents

By W. L. Austin

The only essential difference among the three methods of collecting the precious metals from their low-grade ores by fusion is comprised in the nature of the vehicle in which those metals are concentrated. If lead- or coppper-ores are used, the processes are respectively lead- or copper-smelting; but when the sulphide of iron forms the matrix in which the gold and silver are collected, the process is known as pyritic smelting. The latter method presents rarely any advantages when lead- or copper-ores are available at rates which permit profitable treatment. Pyritic silver-smelting, defined by Percy as " the smelting of silver-ores, which are either free from lead or do not contain it in sufficient quantity to collect the silver, in conjunction with pyrites, in order to produce a regulus in which the silver may be concentrated," is not, as the name would imply, confined to ores of this metal alone, but embraces auriferous silver-ores, or even gold-ores simple. This method of collecting the precious metals from lowgrade dry ores, employed at Freiberg by Barthel Kohler in 1585, does not appear, up to the present, to have been introduced into this country on a working scale. And yet the possibility of getting rid in a single operation of all the earthy or siliceous gangue of a lowgrade ore and concentrating the precious metals in a matte without loss of lead (which includes gold and silver) by slagging, or volatilization, at the same time producing a highly siliceous slag, very nearly if not quite as clean as is usual in lead-smelting, certainly commends itself. In some parts of the country, owing to the com-

Jan 1, 1888

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

By R. Lingle, E. Hardin, M. Board, H. Pratt, W. Ubbes, M. Voegele, N. Barton

A 2 m. cube of jointed, Pre Cambrian biotite gneiss was subjected to uniaxial and biaxial loading at ambient and elevated temperature. The effects of different boundary conditions on the following rockmass properties were investigated: deformation modulus, joint stiffness, dynamic modulus, coefficient of thermal expansion, thermal diffusivity and conductivity, and joint permeability. Test conditions ranged between 0 and 6.9 MPa uniaxial and biaxial load, and 12° to 74°C mean block temperature. The tests were performed as part of the Office of Nuclear Waste Isolation program for evaluating site charterization test methods for measuring the hydro-thermal-mechanical properties of rock masses. The fracture flow experiments discussed in this paper were described in detail in a similar paper given to this symposium in 1981 (Voegele, 1981). DEFORMATION MODULUS Horizontal deformation measurements oriented parallel to the loading direction were made at the block surface. Several instrument types were employed: surface short-rod extensometers, bonded strain gauges, vibrating wire strain gauges and the Whittemore caliper strain gauge. Two vertical and two slant borehole extensometers measured vertical displacement. Loading history, especially during uniaxial loading, was critical to interpretation of observed deformation and fracture flow data. This important tendency has been observed in other large-scale laboratory (Bandis, 1980) and field tests (Pratt, et al., 1977). Excavation of the block resulted in minimal disturbance to the intrinsic condition of the sample. Even so, permanent, unrecovered "set" was imparted to the block beginning with the first low-stress biaxial load cycle to 3.45 MPa (Table 1). Unloading

Jan 1, 1982

Elected Died 1895 ABBOTT, AI ATTHUR 1908 1882 ABBOTT, ARTHUR V 1906 1905 ABE, MASAYOSHI 1909 1903 ADAMS, CHARLES C. 1905 1906 ADAMS, JOHN C. 1913 1905 ADAMS, WILLAMS 1909 1903 ADAMS, W. EDWARDS 1910 1884 ADDY, MATTHEW 1896 1906 AFFLECK, WILLIAM A. 1911 1889 AKERS, WILLIAMS A. 1906 1905 ALABASTER, RUPPERT C. 1911 1899 ALBERGER, LOUIS R. 1911 1894 ALLEN R B 1896 1905 ALLEN, R. SCOTT 1906 1886 ALLISON, ROBERT 1916 1874 AMIOT, H. 1892 1886 AMSLER, CARL 1894 1898 ANDRSON, JOHN W 1905 1895 ÅNGSTROM, CARL 1901 1887 ARCHBALD, JAMES 1910 1900 ARLETT, GEORGE H 1906 1895 ARMSTRONG, JOHN F 1898 1905 ARNOLDS, LEO F. 1917 1882 ARNOLDS, HUGO 1886 1875 ASHBURNER, CHARLES A 1889 1872 ASIIBURNER, WILLIAM 1887 1883 ATKINS, C M , JR 1885

Jan 1, 1923

By H. F. Yancey

Various criteria for evaluating the performance of coal washeries are discussed critically, with particular reference to ideas developed at the First International Conference on Coal Preparation held in Paris in June 1950. Criteria that relate only to the sharpness with which a cleaning unit separates coal from impurity are compared with those that reflect loss of coal or quality of products.

Jan 6, 1951

By N. M. Langdon

Spokane Meeting, September, 1909.) THE following corrections to the paper of Mr. Langdon (Bulletin No. 34, October, 1909, pp. 919 to 940), received after the publication of the paper in the Bulletin, will be incorporated in the paper as finally published in the forthcoming Vol. XL. of the Transactions, but are here presented for the information of members:' Page. 921. Table I., furnace M2, item 11. For " 8801 " read "0.8801." 922. Table II., furnace C, item 2, under gas. For " 0.011 C " read " 0.011 0." Furnace G, item 13, under gas. For " 5.074 air " read " 3.074 air." Item 15, 114.269 " should be " 4.289." Furnace H, item 2, under iron. For " 0.04 " read ".0.01." 923. Table II., furnace J, item 1, under iron. For " 0.95 " read " 0.93." Furnace N2, item 6, under gas. For " 0.66 CO," read 0.066 C02." 924. Table III., furnace C, item 17. For " 379 " read " 397." 927. Table IV., furnace C, item 4. For " 0.0124 " read 0.0424." Furnace G, item 15.. For " 4,060 " read " 4,066." 928. Line 2. Items 19 and 20 of heat-supply, should be items 20 and 21. 930. Line 3. Expunge remainder of paragraph after the word " supplied," and substitute the following : "As compared with the fusion-zone, the loss by radiation n C was 25.5 per cent. of the total (2,278 units) supplied to that zone, while in D it was 22.5 per cent. of the total heat (1,824 units) supplied to that zone. Finally, as compared with the reduction-zone, C lost by radiation 36.8. per cent. of the 1,580 units supplied to that zone,

May 1, 1910

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Jan 1, 1908

By Owen S. Roberts

During the design phases of a conveyor system, the question arises regarding the type of drive required for each application. The paper shows that the correct drive for any particular application is the one that satisfies the criteria established for that application in the most economical manner consistent with such considerations as site location, availability of spare parts, area environmental conditions, power supplies available, etc. Following discussions of various mechanical arrangements for the drives, motor types and their characteristics are considered along with the control means of modifying these characteristics to satisfy individual requirements. These characteristics are all illustrated graphically. After selecting the motor and its starter, control accessories and interlocking arrangements as applied to material handling systems are discussed.

Jan 1, 1973

By Robert Forsyth

IN working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remark- able when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

Jan 1, 1876

Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'3S) Min. Engr., Dir., Bu¬ reau of Mines. Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch, Morenci. Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Ten¬nessee Coal Iron & R.R.. Co., 1542 Brown -Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Command¬ing, Officer, Pittsburgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D., (M'32) Alin. Engr.. Div. of Cor¬porations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur, Ga. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co., Led., Vatnkoula, Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Bans. Abernathy, Jack H., (M'40) Peer. Engr., c/o Superior Oil Corp., National Bank of Tulsa Bldg., Tulsa, Okla. Aborn, Robert H., (M'10) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'39) Peer. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles, Calif. Abramowitz, William L., (J'40) Chem., Industrial Inventions, Inc., 103 Foster Se., Peabody, Mass.

Jan 1, 1942

By Lawrence W. Teufel

An anelastic strain recovery technique is presented as a method of determining the directions and ratio of the maximum and minimum horizontal in-situ stresses from oriented cores from deep wells. Predictions of hydraulic fracture azimuth inferred from principal stress directions determined from both elastic and time-dependent (anelastic) strain relaxation measurements of volcanic tuff are consistent with the observed orientations of hydraulic fractures produced in simulation and mineback experiments, underground at the Nevada Test Site. In addition, anelastic strain recovery measurements on oriented cores of shale and sandstone from well depths of about 1680 meters show consistent relaxation directions of the principal horizontal strains and have enabled a prediction of the principal horizontal stress directions and hydraulic fracture azimuth.

Jan 1, 1982

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President's Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921

PAUL D. FOOTE AND T. R. HARRISON, Washington, D. C. (written discussion *).-There are several methods for measuring the internal resistance of a battery, the line resistance in a circuit containing an e.m.f., or the true value of this e.m.f. The writers, however, were the first to em-ploy a simple principle whereby the total resistance of the circuit is ad-justed to a preassigned value for which the scale of the millivoltmeter is graduated, the only e.m.f. employed being that of the source measured. One of the simplest forms of these instruments is described on page 2842, September Bulletin. In papers now in the press we have described some twenty modifications of this simple design but all operating upon the same fundamentally new principle. The instrument devised by Mr. . Porter is of this general type but, unlike the designs we have recom-mended, is open to serious objections.

Jan 12, 1919

By Tong Guangxu

INTRODUCTION Throughout the world, the caving mining methods of ore-draw under the overlying waste rock are sublevel caving in Sweden, block caving in U.S.A. and forced block caving and sublevel caving with sill-pillar in U.S.S.R. These caving methods are of high efficiency, low cost and large production (especially the block caving method) when compared to opencast mining. From the ore production of all under- ground mines, the largest annual production of underground metalliferous mines in the world is caving methods. The sublevel caving in Kiruna Iron Mine of Sweden has reached annual ore production over 20 million tons in 1974. The block caving in Climax Molybdenum Mine and San Manuel Copper Mine of U.S.A. both have produced about 40 thou- sand tons of ore per day in 1971. At the same time, the productivity of Kiruna was 12 thousand tons of ore per man-year, Climax 42.8 tons (48.3 short tons) per man-shift and San Manuel 29.01 tons (32.1 short tons) per man-shift. The main feature of this group of mining methods is the underground extraction of ore from beneath overlying caveable waste rock. Since the loss and dilution of ore are inherent (sometimes to a great extent), the control of ore-draw in these methods as com- pared with other methods is very important. Consequently, concerned Universities and Research Institutes have devoted great amounts of research on ore-draw theory and control management which has provided positive results to mine production, and has apparently promoted the development of the caving methods. During 1979 in China, metalliferous underground mines accounted for 15.22% of the total iron ore produced, while also accounting for 56% of total non-ferrous production. According to the mining methods, sub level caving in the principal underground iron mines counted for about 56.74% of total principal underground iron mine production, but only about 1% of total non-ferrous underground mine production. Relative to forced block caving and sublevel caving with sill pillar, the Chinese non-ferrous under- ground mines estimated about 35% of total non-ferrous underground mine production from these two methods, mainly from the latter. From the trend of development of underground metalliferous mines in China, the percentage of production in caving will be increased in the future, especially in block caving and forced block caving which have already been given great attention in the mining circle. In these types of mining methods the ore is drawn from the stope under a large area of overlying waste rock, which complicates the basic regulation and control of ore-draw, but provides lower loss and dilution than sublevel caving. Because of these reasons, the Kiruna Iron Mine in Sweden is intending to change its sublevel caving by testing a sublevel shrinkage caving method and considering a large area of ore-draw beneath the stope as an advantage. Therefore, the basic regulation and control management of ore-draw under a large area, as practiced in China, will be discussed in this paper. BASIC REGULATION OF ORE- DRAW FROM CAVING STOPE The aim of studying ore-draw under a large area of overlying waste rock is to se- cure a planned draw schedule that guarantees a certain plane of interface between ore and waste rock, and controls the change of its shape in spatial position for reducing ore loss and dilution during the draw process. Presently, the ellipsoid theory is comparatively near the actual attitude of ore-draw from the cave. 1. Ore Drawn Out from Single Drawpoint Laboratory testing and practical experience all show that after a certain amount of ore has been drawn out from a drawpoint, its original shape in the stope before drawing is more or less similar to an ellipsoid, hence the name "draw ellipsoid." This draw ellipsoid is cut at the bottom by a horizontal plane corresponding to the raise of the drawpoint, and its volume can be calculated by the following formula:

Jan 1, 1981

By J. C. Bierlein, R. A. Dodd

Endurance strengths at 10' cycles, fatigue-hardening rates, and endurance strength/0.2 pct proof stress ratios have been determined jbr a range of Cu(Ni), Cu(Si), and S.R.0. Cu(Au) solid solutions. Some douht is cast on simple cross slip models of fatigue hardening in view of opposite composition dependencies of hardening displayed by Cu(Si) and Cu(Au). The temperature dependencies of hardening also are the opposite of predictions made on the basis of a cross slip model. A correlation apparently exists between the fatigue strength/0.2 Pc~ proof s1.re.s~ ratios and rates of fatigue hardening. An increase in PS/PS due to alloying or temperature change is accompanied by a decrease in hardening rate, and vice versa. In recent years there has been much interest in the determination of the dislocation structure of fatigued metals and alloys. The accumulated evidence, e.g., Refs. 1 to 5, suggests that the structure may be dependent on the stacking fault energy, 7, of the fatigued metal in the same way that fatigue hardening rates have also been shown to apparently depend on u .6' 7 The above research followed the various earlier theories relating crack nucleation to ease of cross slip, e.g., Refs. 8 to 131 so "ggesting that y may indeed be the parameter of principal significance in all facets of the fatigue process. However, comparatively little attention has been paid to correlating engineering fatigue data with observations of the above type. Certainly, it would be useful if potential engineering fatigue performance could be assessed from a knowledge of easily determined alloy properties, and the present research originated from this standpoint. TO investigate the widest Possible range of 7 would require the use of two solvent bases, e.g., aluminum and copper, but a reasonable coverage can be provided by copper-based solutions alone. Therefore, it was decided to work with Cu(Ni) and Cu(Si) solid solutions, the approximate stackillg fault energies of which are given in Table I. The y range extends from low, Cu(7.5 at- Pet Si), to moderately high in Cu(2-5 at. ~ct ~i) and two of the Cu(Ni) alloys. The values listed in Table I should be regarded as qualitative only, being derived as follows. Dillamore and smallman14 quote a value of 85 i 30 erg.cm-2 for the stacking fault energy of pure copper, based on an earlier value due to Howie and swannl5 corrected by Brown's formula.'' Since the ratios (alloy)h(pure copper) have been reported17,18 for Cu(Ni) alloys containing up to 30 pct Ni, approximate ) values for these alloys can be computed, and a rough estimate of 7 for Cu(50 at. pct Ni) obtained by extrapolation. The relatively low y value obtained in this way for Cu(50 at. pct Ni) coincides with the observation of Nakajima19 that the stacking fault probability is a maximum at this composition. Likewise, the y values for the three ~u(~i) alloys are estimates based on values given by Swann and Nuttingo corrected on the basis Of Brown's estimate that the true 7 values are probably 2.3 times greater than those originally computed. In addition to the above alloys it was decided to investigate short-range ordered (s.R.O.) CU(AU) alloys containing up to 25 at. pct Au. This last alloy has been shown to have a well-defined planar arrangement of dislocations when deformed,21,22 probably due to cross slip being restricted by the S.R.O. Engineering fatigue data was to be represented by the determination of endurance strengths, and these were to be correlated with fatigue hardening and mechanical property data. EXPERIMENTAL I, order to study the desired properties and property changes, the following alloys were prepared: Cu(2.5 at. pct Si), Cu(5.0 at. pct Si), Cu(7.5 at. pct Si), Cu(5.0 at. pct Ni), Cu(25.0 at. pct Nil, Cu(50.0 at. pct Ni), Cu(5.0 at. pct AU), Cu(15.0 at. pct AU), Cu(25.0 at. pct AU). The copper and gold were zone-refined, while the silicon was semiconductor grade. The nickel was of 99.95 p,t. purity.* All alloys were induction-melted in a *Kindly supplied by the International Nickel co. helium atmosphere, appropriate precautions being taken to avoid segregation in the Cu-Au series. Rod stock was obtained by rolling and swag,ng. A few Bridgman single crystals were grown for fatigue-hardening studies, but most material was machined into polycrystalline fatigue speciments of the design shown in Fig. 1, and into polycrystalline tensile and fatigue-hardening specimens of simple cylindrical design. All specimens except Cu(Au) were annealed; the latter were quenched from above T, to produce short-range order. A few of the quenched alloys were examined for long-range order by step-scanning over

Jan 1, 1969

New Products Equipment

Jan 6, 1953

D. C. JACKLING, the father of the porphyry coppers, has been honored for his pioneering in that field. There is another facet to Mr. Jackling's activities, one which now may prove an even greater monument than the big coppers-the story of his venture in taconite beneficiation. The essence of his porphyry development was mass handling of material. Not alone mining on a large scale, which was done on the Mesabi Range at the turn of the century, but the integration on a previously unknown scope of mining, milling, concentration, and in many cases, of final reduction to metal at the site. This was mass production applied to mining, treatment of a very low grade source material, previously considered submarginal.

Jan 1, 1954

Jan 11, 1951